Elite Screens Manual SRM Pro Series User manual

Rev. 010710-JA www.elitescreens.com/[e-mail]
Manual SRM Pro Series
Premium Quality Manual Pull-Down Projection Screen
User’s Guide

Rev. 010710-JA 1
1. Mark the location of where the screen is to be installed for the pre-
drilled hole.
2. After marking the area and drilling the hole, insert the proper screw into the drilled hole and leave
about 1/8” of an inch from the wall to mount the screen.
3. Mount your screen from the keyhole located on back of screen’s left and right end cap.
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
Front view
A. Flush Wall Mounting
B. Ceiling Mounting (additional hardware required)
Optional installation using a chain to hang the screen from the ceiling.
1. You can also hang the screen on a ceiling by using a chain (not included) and hang it by the two d-rings
loops located on each end of the case.
Side view

Rev. 010710-JA 2
SCREEN OPERATION
Note: Always pull the screen down or let it up in a 90-degree vertical angle. Do not allow the screen to touch the
screen case when the screen goes up or comes down to avoid damaging the screen material.
1. Pull the screen down from the lanyard or from the handle only in a 90-degree angle. Do not attempt to pull the
screen down by the surface or touch the screen, as it will damage the screen and void the warranty.
Note: An internal auto-lock mechanism system will cause the screen to stop and lock on the position at
intervals.
2. If you want to the screen to retract back, simply pull the screen down more than 2 inches and retract the
screen back releasing it up gently. The screen is equipped with a SLOW RETRACT MECHANISM which
allows the screen to slowly retract without the need to hold on to the handle or lanyard. Simply release the
handle and the screen will retract by itself.
Note: Always release at a 90-degree angle. If ever the screen feels stuck, keep in mind that the screen’s
mechanism is new and needs to be brought up/down a few times to loosen up. If this happens, carefully
with a little force, yank the screen straight down to unlock the screen.
Note: Improperly bringing the screen up/down will damage the screen material or rolling system.

Rev. 010710-JA 3
Unit: mm
Models
Diagonal
Size /
Aspect
Ratio
Case
Length
(A)
Viewing
Width
(A1)
Screen
Width
(A2)
Weight
bar
Length
(A3)
Bottom
Edge
Distance
(B2)
Screen
Material
to Weight
Bar
Height
(B3)
Viewing
Height
(B1)
Screen
Overall
Height
(B)
End cap
Height
(B4)
End
cap
Width
(C)
Screen
material
distance
to wall
(C1)
M84VSR-Pro 84" (4:3) 1867.0 1707.0 1783.0 1863.0 62.0 1456.0 1280.0 1552.0 96 80 20
M100VSR-Pro 100" (4:3) 2192.0 2032.0 2108.0 2188.0 62.0 1700.0 1524.0 1796.0 96 80 20
M120VSR-Pro 120" (4:3) 2598.0 2438.0 2514.0 2594.0 62.0 2005.0 1829.0 2101.0 96 80 20
M84HSR-Pro 84" (16:9) 2014.0 1860.0 1936.0 2010.0 62.0 1222.0 1046.0 1318.0 96 80 20
M100HSR-Pro 100" (16:9) 2374.0 2214.0 2290.0 2370.0 62.0 1421.0 1245.0 1517.0 96 80 20
M120HSR-Pro 120" (16:9) 2816.0 2657.0 2733.0 2812.0 62.0 1670.0 1494.0 1766.0 96 80 20
Unit:inch
Models
Diagonal
Size /
Aspect
Ratio
Case
Length
(A)
Viewing
Width
(A1)
Screen
Width
(A2)
Weight
bar
Length
(A3)
Bottom
Edge
Distance
(B2)
Screen
Material
to Weight
Bar
Height
(B3)
Viewing
Height
(B1)
Screen
Overall
Height
(B)
End cap
Height
(B4)
End
cap
Width
(C)
Screen
material
distance
to wall
(C1)
M84VSR-Pro 84" (4:3) 73.5 67.2 70.2 73.3 2.4 57.3 50.4 61.1 3.8 3.1 0.8
M100VSR-Pro 100" (4:3) 86.3 80.0 83.0 86.1 2.4 66.9 60.0 70.7 3.8 3.1 0.8
M120VSR-Pro 120" (4:3) 102.3 96.0 99.0 102.1 2.4 78.9 72.0 82.7 3.8 3.1 0.8
M84HSR-Pro 84" (16:9) 79.3 73.2 76.2 79.1 2.4 48.1 41.2 51.9 3.8 3.1 0.8
M100HSR-Pro 100" (16:9) 93.5 87.2 90.2 93.3 2.4 55.9 49.0 59.7 3.8 3.1 0.8
M120HSR-Pro 120" (16:9) 110.9 104.6 107.6 110.7 2.4 65.7 58.8 69.5 3.8 3.1 0.8
*Measurement dimensions are intended as a reference only and subject to change without notice
Note: Data Error ±1"
Manual SRM Pro Series Dimensions Table
Clean matte white screen material with a soft cloth and mild soap with water. When not in
use, retract screen in its housing to keep the screen material surface clean.
Regardless of mounting method, the screen should be securely supported so that vibration or even abusive
pulling on the viewing surface will not cause the case to work loose or fall. The installer must insure that the
fasteners used are of adequate strength and suitable for the mounting surface chosen.

Rev. 010710-JA 4
Two (2) year warranty parts and labor (as of June 2007) from defects in
workmanship from purchase date as follows (except for refurbished units as specified below):
Refurbished units carry a 90-day parts and labor warranty.
Demo units or open box items are AS IS items and do not carry a warranty.
Each party will be responsible for one way shipping during the warranty period. Elite Screens is not responsible for
applicable International tariffs such as broker fees and customs duties.
A RMA (Return Merchandise Authorization) number must be issued in order to process a replacement or to
authorize a return for warranty repair. Elite Screens will, at its sole option, replace or repair the defective unit with a
replacement *(see exceptions below) after the defective unit is received. Once the product is received, Elite Screens
will send out a replacement *unit to the customer by ground service (subject to inventory availability). Please do not
return any unauthorized items to Elite Screen, as they will be refused. The RMA number must be included on the
outside label of your shipping box. Our warehouse is not authorized to accept returns without an RMA number on
the shipping label. RMA numbers are valid for 45 days from the date of issue.
Missing Parts must be reported within the 7-day grace period. If reported after 7 days, customer will only be
responsible for shipping and handling fees. If reported after 30 days of receipt, customer is responsible for cost of
the parts and shipping & handling fees.
*A new or refurbished replacement will be sent out to the customer depending on the type of purchase (new or refurbished) or
based on stock availability.
Please visit link below for full warranty information
For Customer Service and Technical questions, please contact Elite Screens at:
Telephone: [phone]
Fax: [phone]
For Warranty and Service requests please fill out a RMA /Service Form at:
http://www.elitescreens.com/service_form.htm.
Please Visit this link for full Warranty information:
http://www.elitescreens.com/warranty_policy.htm
Warranty Policy

Rev. 010710-JA 5
REMEMBER TO REGISTER YOUR WARRANTY AT
WWW.ELITESCREENS.COM/REGISTER.HTM
US & Canada Tech Support & Warranty Claim
Please contact us at [e-mail] or call [phone] #3 Service
Europe Tech Support & Warranty Claim
Please contact us at [e-mail] or call [phone]
Asia Tech Support & Warranty Claim
Please contact us at [e-mail] or call [phone]
Taiwan Tech Support & Warranty Claim
Please contact us at [e-mail] or call [phone]
America:
Elite Screens Inc
16410 Manning Way
Cerritos, CA 90703 USA
Tel: [phone] (877-511-1211)
Fax: [phone]
[email protected]m
www.elitescreens.com
Europe:
Elite Screens Europe GmbH
Lübecker Straße 1
22087 Hamburg, Germany
Tel: [phone]
Fax: [phone]
[email protected]
www.elitescreens.eu
Elite Screens France S.A.S
11, Allée William Penn
92150 Suresnes, France
Tel: [phone]
Fax: [phone]
Latin America Contact:
[e-mail]
East Asia Contact:
[e-mail]
India Contact:
[e-mail]
Japan Contact:
[e-mail]
Asia:
Elite Screens China Corp.
Longxi Duimianling Industry Zone Longcheng
Longgang District,
ShenZhen GuangDong, China
Tel: [phone]
Fax: [phone]
[email protected]m.cn
www.elitescreens.com.cn
Taiwan:
Elite Screens Taiwan Co. Ltd.
No.38, Alley 22, Lane 66, Sec. 5
Nanjing E. Rd., Songshan District
Taipei City 105, Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
[email protected]m.tw
www.elitscreens.com.tw