Elite Screens QuickFold Q100V User manual

Folding Presentation Screen
QuickFold Series
Users Guide

Setup Procedure
The frame and supports are made of 1 3/8” aluminum tubing with an anodized finish. Please follow the instructions in
this package. With proper care, your QuickFold screen will provide many years of reliable service.
fig 2
Top
fig 1
Two Section Frame
(For presentation screens that are less than 120” in diagonal measurement)
1. Take the frame out of the case and remove its wrappings. Unfold the
main joints as shown in (fig 1).
2. Once the main joints are unfolded, make sure that the snap latches
“click” into the locked position. The frame should now be fully
elongated as in (fig2). *Note: The snap latches will automatically
lock when the joint is straightened. Press the snap latch button in
order to release the lock.
3. While holding the bottom of the frame in place, lift the top of the
frame to unfold the sides which will cause the snap latches lock
when fully extended. Secure the corner braces into the locked
position. The screen frame should now be fully opened as in (fig 3).
fig 3
Lock down the corners
Snap latch
Snap latch
Top

Three Section Frame
(For large presentation screens that are 120” or more in diagonal
measurement)
1. Take the frame out of the case and remove its
wrappings. Unfold the main joints making sure that
both the end and middle spans are in prefect alignment
as shown in (fig 4).
2. Make sure that the snap latches have locked the joints in
the frame so that it is at its full horizontal extension as
shown in (fig 5)
3. While holding the bottom of the frame in place, lift the
top of the frame to unfold the sides which will cause the
snap latches lock when fully extended. Secure the
corner braces into the locked position. The screen frame
should now be fully opened as in (fig 6).
fig 4
Top
fig 5
fig 6
Lock down the corners
Snap latch
Snap latch
Top

Standard T-Leg Support
1. Take the T-Leg out of the case and remove its wrappings.
Fold down the support legs as shown in (fig 7).
2. Secure the corner braces into the locked position as shown
in (fig 8)
3. Unfold the T-Leg’s main support until the snap latches
“click” into the locked position as in (fig 9).
fig 7
fig 8
Lock down the corners
fig 9
Snap latch

locking bolt
frame spacer
fig 12
fig 10
fig 11
Snap latch
AT-Leg (optional support buttress recommended for the
large screens with diagonal measurements of 150” and
over)
1. Take the AT-Leg buttress out of the case and remove its wrappings. Unfold the buttress as shown in (fig 10).
2. Snap latches will automatically lock in the center joint. Use the snap latch buttons to unlock the end joints as
shown in (fig 11).
3. Attach the AT-leg to the T-Leg by securing the locking bolts through the frame using the frame spacers
between the metal parts as shown in (fig 12) (*Note: It is important to always use the plastic frame spacers
between the pieces whenever connecting any of the aluminum surfaces such as T-bars to AT, SAT and Frame
components.)

lockingbolt
frame spacer
fig 15
fig 13
fig 14
SAT-Leg (optional added stability buttress recommended
for the large screens with diagonal measurements of 180”
and over)
1. Take the SAT-Leg out of the case and remove it wrappings as shown in (fig13).
2. Undo the snap locks to loosen and bend the joints for proper fitting as shown in (fig 14).
3. Attach the SAT-Legs by securing the locking bolts through the frame using the frame spacers between the metal
parts as shown in (fig 15)

A
lockingbolt
frame
leg
frame spacer
ttaching the Frame to its Supports
1. Always use at least two locking bolts through the T-Leg Support, the Spacer and into the Frame on each side.
2. Height can be adjusted in 8” increments up or down. Normal screen height is 44” from the bottom of the frame to
the floor.
3. Reverse this process to dismantle and pack away the screen.
snap latch button
Folding the Picture Surface for Packing
Please observe the following precautions before folding up the screen material.
1. Do not bring the viewing surface into contact with chemical solvents, sharp or abrasive objects, painted,
varnished or plastic finished items.(*See the cleaning instructions for exceptions to this)
2. Make certain that the screen is laid out on a dry, clean and flat surface.
Folding up the screen:
Lay out the screen with the viewing surface facing up and cover it with flat (not crumpled) tissue or packing paper that is
clean and unprinted. *Note: Do not ever use abrasive paper, newspaper or any printed material on your projection
screen.

1. With the viewing surface facing up, fold the fabric in half from top to bottom. When folding, make certain that
the viewing surface does not come into contact with the black binding, grommets or snap buttons. *Note: The
screens are shipped from production with tissue paper in the folds that should be retained for future use.
2. Make sure that the first folds never exceed 3 feet in width (fold again if necessary). Also make sure that there is
always clean packing paper in between the two surfaces.
3. Larger sized screens will need to be folded with more frequency than smaller screens. Follow the instructions
from step 1 as well.
4. Fold the material from top to bottom first then alternate in folding left to right until the material is of a sufficient
size that will fit into the leatherette case.
Note: Keep the screen material inside its case when not in use.
Failure to follow this precaution may eventually result in
staining or discoloration.
Cleaning
The screen surface can be cleaned as follows.
Use a clean white cloth (100% cotton preferred) and dampen it with clear water. Gently wipe in one direction and NOT
in a circular motion. Use another dry cloth to dry after each cleaning session. To remove a stubborn stain or sticky
surface, use denatured alcohol (methanol or methyl alcohol) in lieu of water.
Attaching the Screen once it is unpacked
1. Using the snap buttons to connect the Screen material with the case
2. Start at the top working in whatever direction is most comfortable to you
3. Stretch the corners if necessary to pair up the buttons with their corresponding snaps

Packing List
1. Frame 1 piece
2. Support (T) Legs 2 pieces
3. AT-Legs 2 pieces (optional depending on size)
4. SAT-Legs 2 pieces. (optional depending on size)
5. Screen Fabric 1-2 pieces
6. Locking Bolt 6-26 pieces
7. Frame Spacer 6-26 pieces
8. Manual 1 pieces
The following points should be noted to assure the sound performance and longevity of your
screen
1. Never use your hand to touch the screen surface.
2. Never scrabble on the screen with anything.
3. Don't touch the screen with hard or sharp objects.
4. Please use a clean cotton cloth or soft dust brush to remove any dust particles on the screen.
5. The screen material may be cleaned
Warranty Policy - Manual, Tripod, Pull-up Floor, and Fixed Frame Screens
*Warranty policy applies to claims made in the United States of America. Warranty issues outside of the US must go
through their international distributor.
•Two (2) year warranty parts and labor from purchase date as follows (except for refurbished units as specified
below):
•Refurbished units carry a 90-day parts and labor warranty.
•Demo units or open box items are AS IS items and do not carry a warranty.
•Elite Screens will cover ground shipping charges on warranty claims made within 7 days of receiving per our
DOA (Defective On Arrival) policy
•Each party will be responsible for one way shipping during the regular warranty period if the claim is made
after the 7 day DOAperiod.
•An RMA (Return Merchandise Authorization) number must be issued in order to process a replacement. Elite
Screens will either replace or repair the defective unit with a brand new replacement *(see exceptions below)
after the defective unit is received and/or confirmed defective. Once the product is received, Elite Screens will
send out a new *unit to the customer by ground service (subject to inventory availability).
•Missing Parts must be reported within the 7-days of receipt. If reported after 7 days, customer will only be
responsible for shipping and handling fees. If reported after 30 days of receipt, the customer is responsible for
cost of the parts and shipping & handling fees.
Please visit the link below for full warranty information
http://www.elitescreens.com/services.html
*Anew or refurbished replacement will be sent out to the customer depending on the type of purchase (new or refurbished) and is
based on stock availability. 安装幕布 分别将幕布四个角上的按扣扣在框架上，再依次扣上余下的按扣

TWO WAYS TO REGISTER YOUR WARRANTY WITH ELITE SCREENS INC.
A. On Line (Faster and Easier) www.elitescreens.com/register.html
B. Fill out & Fax to [phone],Attn: Customer Service Dept.
*Your Name: _______________________________________________________
Address: ____________________________________________________________
City/State/Zip ________________________________________________________
*Email Address: ______________________________________________________
*Phone: _____________________________________________________________
*Screen Model: _______________________________________________________
*Serial Number: _______________________________________________________
*Date of Purchase: _____________________________________________________
*Dealer / Reseller Purchased from (name of the reseller): _____________________
What is your Projector Model :____________________________________________
Application: ___ Home ___ Education ____ Corporation _____ Government
___ Others
How would you rate this screen? ___ Excellent ___ Good ___ Ok ___ Improvement needed
Comments:
Contact info:
If you have pictures of your screen you’d like to share with us, please
email your pictures to [email protected]
or call us at 877-511-1211
www.elitescreens.com
For any technical inquiries,
[e-mail]