Elite Screens Kestrel Series User manual

11/29/2016 www.elitescreens.com 1
Kestrel Series
(Version 2)
Electric Floor Rising Projection Screen
USER’S GUIDE
IMPORTANT SAFETY NOTES
1. Please read th is manua l bef ore use an d f oll o w the p ro ce du re s spe c if ied :
a. Please retain this manual for future reference.
b. To avoid any damages to the screen, do not use any accessories or parts not recommended
by Elite Screens.
c. Handle the device carefully during transportation.
d. o not set up screen on uneven surfaces.
e. To prevent electrical shock or fire; never over load the power cord, and avoid contacting the
motorized components with liquids or foreign objects.
2. The tubular motor equipped in the electric creen feature an overheat protection en or.
If the creen i con ecutively brought up and down between 3-4 minute , the motor will
automatically hut-off to prevent the motor from u taining damage through overheating. If
the automatic hutoff i activated, plea e allow 30 minute cool down before re uming
operation.
3. The Ke trel Serie Screen i equipped with a trong ten ion cro - pring y tem. Plea e do not
attempt any unnece ary repair . It i at your own ri k to open the in ide cover or
di mantle/work on the creen. Individual modification to thi product are prohibited and will
void the u er’ warranty.
4. When using the screen, please
a. Avoid strong wind, rain, or electrical storms.
b. No direct sunshine (UV Radiation)or moisture.
c. Keep away from fire sources and high temperature devices.
d. Turn off the power before moving this product.
K
eep away from
ch
il
dren
Keep
hands clear
f
rom the
closing panels

11/29/2016 www.elitescreens.com 2
NOTE
• This equipment has been tested and found to comply with the limits for a Cla B digital device
pursuant to Part 15 of the FCC Guidelines.
• The products are designed to provide reasonable protection against harmful interference in
a residential/commercial installation and end user application and may radiate radio frequency
energy.
• However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. The power outlet should be close to the unit and easily accessible.
2. Re-orient or relocate the receiving antenna.
3. Increase the separation between the equipment and the receiver.
4. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Ke trel Acce orie :
Screen Operation:
Power: Connect the screen to the power supply and switch the power button on. Now it is ready for use.
Qty 1
Radio Frequency
Remote Control
Qty 1
Infrared
Remote Control
Qty
1
Micro USB
Charge Cable
ON
OFF

11/29/2016 www.elitescreens.com 3
Setup: Remove the IR Receiver from the housing on the left side of the Ke trel Floor Electric Screen as
shown in the pictures below.
About the Control Sy tem:
1. Manual Operation Switch: The left side of the screen's housing includes a UP/STOP/ OWN switch to
raise, lower and stop the screen without the use of the RF/IR remote. See image below for reference.
Please note, the screen power supply switch must be ON for use of this Manual Switch.
2.
RF (Radio Frequency) and IR (Infrared) Remote : The Kestrel Series screen includes both IR and
RF receivers that enable the consumer to use either the RF or the IR remote control. The RF remote is
best used when the screen is concealed or long distance control is required. The RF technology therefore
is more versatile as it doe not require line of sight to operate the screen.
The IR remote require a direct line of sight through the screen’s IR receiver.
Up / Stop / Down
IR
receiver

11/29/2016 www.elitescreens.com 4
About the RF/IR Remote Control :
The new remotes, included in this version of the Kestrel
Series, are touch sensitive remote controls. Please be sure
to place your finger directly in the center of the button when
attempting to control your screen. You will see a blue light
flash above the buttons when used properly.
Note: When operating your screen to open, the motor will automatically roll back and adjust to make sure
the fabric is properly tensioned as the screen raises to the suitable position.
Charging the RF/IR Remote Control:
Once charging is needed, plug the Micro USB Charge Cable into any USB power source and into the left
side of your RF or IR Remote Control. While charging, you will see a solid red light above the touch
sensitive buttons. For your convenience, you may use the remote while it charges.
Note: The red light may dim while charging.
Storing the creen:
Always store the screen flat horizontally. Never store the screen in a vertical position.
Screen Maintenance
1. Always close the screen when not in use
2. o not touch the screen surface
3. Keep away from direct sun and high/low temperatures
4. For indoor use only
5. Clean with soft water
6. o not drop/close screen consecutively for more than 3 minutes. This is to avoid overload protection
shut-off. If automatic shut-off occurs, please wait for 20-30 minutes to try again.
For local Elite Screens contact or Technical Support, please visit
www.elitescreens.com
Charge port UP
STOP
DOWN