Elite Screens OMS103HR User manual

042117DR www.elitescreens.com 1
Yard Master Series
Rear Projection Outdoor Movie Screen
User’s Guide (v. 2)
Note:
1. The Ring-Stakes, Curved-Stakes & Guy Rope should always be installed for Stability.
2. Use of this product is not recommended in gusty winds over 20mph.
Maintenance:
1. Soft cloth with mild soap &water may be used to clean the screen’s surface.
2. To prolong the lifespan of this product, store it in its carry case when not in use.
Parts checklist (Model: OMS103HR/OMS123HR)
A. Screen material x1 B. Steel tube x12-14 C. Fiber glass pole x4
D. Carrying bag x1 E. Guy-ropes x4 F. M6hex nuts x2
G. Curved stake x4
H. Ring stake x4
I. M6x43mm hex screw x2
J. Velcro band x24 K. Lock Pins (Spare parts) x 5
A. Main Support Metal Frame Assembly
1. Assemble the steel tube frame by connecting the letters on the ends of the tubes together as shown in the
picture. For example, A to A, B to B etc.
14 Top/Bottom sections - 15cm bands
10 Left/Right sections - 13cm bands

042117DR www.elitescreens.com 2
2. A and Jare attached and secured with the provided Hexagonal Screws (G). This will be the last step.
Step 2:Screen Material Frame Assembly (Fiber glass poles)
1. Join the Fiber Glass Pole to form a straight support rod as shown in the diagram below.
2. Repeat to complete the two horizontal rods. Keep the two vertical rods disconnected for the next steps.
Step 3: Attaching the screen material to the frame
1. Lay out the material on a clean, scratch-free area.
2. Insert the horizontal support rods into the top and bottom sleeves of the screen material.
Horizontal support rod
3. After the frame has been built, lay it on a clean
scratch-free area.
Horizontal support rod
Horizontal Support Rod x2

042117DR www.elitescreens.com 3
3. To insert the vertical support rods, fold the material in half (long ways)
at the middle opening. Insert both ends of the rod into each half of the
material as shown in Fig.1.
4. Keeping the frame laid flat, place and center the screen material (Elite Screens logo facing up) inside the metal
frame.
5. Attach the screen material by the exposed areas of the vertical and horizontal support rods onto the metal frame
wrapping the velcro bands around the rod and frame. Two people are recommended for the following steps.
Front of Screen material
While folded in half, match the connecting ends of the rod and slowly
lower and flatten the material to have the rod connect.
(Shown below in Fig. 2)
Repeat for other side.
Fig. 1
Fig. 2

042117DR www.elitescreens.com 4
1. With one person at the top of the
frame and the other at the bottom, begin
by attaching the material with the velcro
bands, starting at the 3 middle sections
keeping the material centered and evenly
tensioned.
2. Next, with one person at each side,
attach the left and right sides of the
material with the velcro bands, starting
with the 3 middle sections.
3. Leaving the corner sections for
last, attach the remainder of the top and
bottom material with the velcro bands,
using one person on each side to
maintain even tensioning and a
centered screen. .
Note:
Attach the bands on the left and right sides
as tightly as possible. This will provide the
tension required to make the screen material
flat.
3
3
2
2
1
1

042117DR www.elitescreens.com 5
Step 4: Final Assembly and Main Frame Support set up
1. Stand the frame upright, and rotate the legs (A) and (J) 90 degrees and insert the hexagonal screws. Secure
using the M6 hex nut (I) place.
2. Ensure the ring-stakes and guy rope are properly used to safely secure the screen to the ground during use.
3. Drive the Curved Stakes (G) through each hole on the ends of the legs.
4. Drive the Ring-Stakes (H) to the ground and attach a Guy-Rope on each side for additional support and
stability.
A
J
M6hexagonal screw
M6 hex nut
Legs A and J are to be
rotated 90 degrees.
4. Lastly, tightly attach the corner
sections of the material with the velcro
bands.Your screen should look like the
figure shown (to the left).
Note:
After all velcro bands are attached, check
each individual band for equal tension. If
needed, tighten the bands until desired
tensioning is achieved.

042117DR www.elitescreens.com 6
Warning Instructions
1. The Ring-Stake and Curved Stake should be properly driven into the ground to avoid the frame from
falling which could result in injury or permanent damage to the screen.
2. Always be cautious of strong windy conditions. We don’t recommend using over 20mph.
3. A soft terry cloth with mild soap and water may be used to clean the screen surface.
For a local Elite Screens contact or Technical Support, please visit
www.elitescreens.com
Ring stake
Curved Stake
Guy rope