Elite Screens EDGE FREE Aeon CineGrey 4D AT Series User manual

Rev.010521DT (DS0189) www.elitescreens.com 1
Aeon CineGrey 4D AT Series
Ceiling Ambient Light Rejecting Acoustically
Transparent EDGE FREE®Fixed Frame Screen
USER’S GUIDE
E Type - V1
Product Description: The Aeon Series is a fixed frame projection screen that uses Elite’s EDGE FREE® technology.
The EDGE FREE® design resembles a giant size flat panel TV display. The Aeon includes a bezel trim to further
enhance the frame appearance and absorb projector overshoot. An optional LED kit is available for back-lighting.
Congratulations on your new Aeon CineGrey 4D AT purchase! The ISF Certified CineGrey 4D AT is an ambient and
ceiling light rejecting (ALR/CLR®) front projection screen material that is perforated for acoustic transparency. It
is precisely formulated for environments with minimal control over room lighting. It was designed to enhance
picture brightness, offer accurate color fidelity, improve contrast and allow sound to pass through.
In order for the CineGrey 4D AT material to maintain its projection qualities and provide optimum performance
please refer to the list below for proper maintenance and cleaning.
The following precautions should always be followed to avoid damaging the material, which is not covered
under warranty.
• Use a dry microfiber cloth or a soft bristle brush to remove dust from the screen’s surface.
• When cleaning, use a damp microfiber cloth with warm water to remove any marks.
• Never rub or apply pressure when cleaning the surface.
• Never attempt to use any chemicals such as acetone, benzene, alcohol, organic solvents or abrasive cleaners to
clean the screen surface.
• To avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils or any other sharp or
abrasive objects.
Visit www.elitescreens.com/aeoncg4d-at-assembly or
Scan QR code for our how to assemble video

Rev.010521DT (DS0189) www.elitescreens.com 2
Make sure all parts are included before commencing frame assembly.
Hardware and Parts List
①Edge Trim A
⑦Long Center Joints b
⑬Elbow Joints a
⑲Support bar
②Frame A
⑧Short Center Joints
⑭Elbow Joints b
⑳Spring a
③Wall Bracket
⑨M4x4 Screws
⑮Elbow Joints C
Spring b
④Anchor
⑩M5x6 Screws
⑯Corner Cover
Fiberglass rod
⑤Wood Screws
⑪Edge Trim B
⑰Frame C
Screen material
⑥Long Center Joints a
⑫Frame B
⑱Edge Trim C
23
22
21
Exploded View of Aeon Frame
Wall installation

Rev.010521DT (DS0189) www.elitescreens.com 3
SCREEN INSTALLATION
⑫
frame B
⑰
Frame C
⑫
frame B
②
Frame A
②
Frame A
⑰
Frame C
1.
⑥Long Center Joints a
⑦Long Center Joints b
⑩M5x6 Screws
⑩
M5x6 Screws
⑭Elbow Joints b
⑬Elbow
Joints a
2.
Note: the support bar is mounted in the upper and lower border
splicing direction as shown on the right
1. Loosen the screw on the
support bar (the connecting
piece can slide).
2. Adjust the connector to
align its hole position with
the border hole position.
3. Fix with ⑨ M4X4 screws.
Frame
M4x4
screws
Support
bar
1. Frame Assembly
2. Center Support Bar Installation

Rev.010521DT (DS0189) www.elitescreens.com 4
Unrolling the screen material
Two people recommended
Back side of screen material
Weighted object
Back side of screen
Note: Backside facing up
(frontside facing down)
Front side of screen
Clean surface area
ATTENTION: Put the gloves on when handling the screen material to avoid touching it with your bare hands.
1 . Put on the supplied pair of white gloves.
This is to avoid leaving oily handprints on
the screen surface which are not
removable.
2. Remove the screen material from the tube
and place a small suitable weighted object at
the end of the material.
3. Lay the material face down, two people
carefully lift the rolled end and slowlyrotate
the material clockwise.
4. Insert the corresponding fiberglass rods on
thru the sleeves on the edges of the material.
Fiberglass rod
a1 = a2 ≒35mm
Backside of screen
22
Note: Please install the six fiber rods into the frame
1 . Carefully and gently place the assembled
frame on top of the screen material.
DO NOT allow the angle edge of the frame to
come in direct contact with the material to
avoid puncturing it.
2. Adjust the distance between the edge of the
frame and the material (a1 = a2) to 1.4”/35 mm
Backside of screen
a1=a2
a2
Backside of screen
a1
3. Screen Material Installation

Rev.010521DT (DS0189) www.elitescreens.com 5
Spring Attachment Method
First hook one end of the spring in the
frame slot, then hold the screen around the
frame to pull, and finally use the spring
hook to pull the spring hook in the screen
hole.
1. Connect Edge Trims A&B to
form the top/bottom trims with
the ⑧Short Center joints,
and then insert them on the
top/bottom frames.
2. Connect the side edge trims
C with the top/bottom edge
trim with ⑮Elbow Joints C.
3. Adjust the trim so that the top
and bottom trim pieces are touching and show no gaps
on the corners. Then fasten them with the ⑨M4 x 4 screws.
4. Attach a spring b on the middle of each edge trim (1-6) to the frame
as shown in the illustration.
5.Insall the ⑯corner covers on the four corners of the edge trim.
3. Begin by simultaneously attaching three springs
in the center of the side frames (C→D) and repeat
for top/bottom frames (A→B).
4. Then, simultaneously attach the springs from the
center to all corners. (Leaving only the four corners.
5. Finally, attach the springs at the four corners
(E→F→G→H).
Backside of screen
Center
connection
⑧Short Center
Joints
⑮ Elbow Joints C
Corner
connection
1
2
5
6
4
3
Edge Trim
Spring b
21
⑯ Corner cover
Front side
Note: Lock front side first
then back side
Back side
Installation of Corner Cover
21
4. Bezel Trim Frame Assembly/Installation

Rev.010521DT (DS0189) www.elitescreens.com 6
*Tolerance may be ±1”
Drill a hole on the wall according to the distance on the chart below distance for your screen. Place the bracket on
the holes and secure them using a Phillips screwdriver. If not installing into a structural wood stud, use a wall
anchor, then screw in the M5x50 screws. Make sure the brackets are leveled.
Screen size
A
B
C
D
110"
96.7” / 2456 mm
95.9” / 2436 mm
54.7” / 1391 mm
53.9” / 1371 mm
125"
109.7” / 2788 mm
108.9” / 2768 mm
62.1” / 1578 mm
61.3” / 1558 mm
135"
118.5” / 3010 mm
117.7” / 2990 mm
67” / 1702 mm
66.2” / 1682 mm
150"
131.5” / 3342 mm
130.7” / 3322 mm
74.3” / 1889 mm
73.5” / 1869 mm
Screen size
110"
125"
135"
150"
L = Left/Right hole distance
59” / 1500 mm
78.7” / 2000 mm
78.7” / 2000 mm
98.4” / 2500 mm
H = Top/Bottom hole distance
47.5” / 1209 mm
54.9” / 1395 mm
59.8” / 1519 mm
67.1” / 1706 mm
6.Wall installation
H
⑤Wood screws
④Anchor
③Top Bracket
⑤Wood screws
④Anchor
③Bottom Bracket
Note: The listed measurements are for general reference only.
D Viewable Height
C Total Height
Border Thickness
28.2mm
A Total Width
B Viewable Width
Bezel Width = 10mm (.39”)
5.Product Dimensions

Rev.010521DT (DS0189) www.elitescreens.com 7
Hanging the screen:
1. Two people hold the screen and align it first with the bottom bracket. The bracket lip must be inserted in the
frame’s channel per example below.
2. Then pull up the screen on the top bracket and adjust the screen left to right as needed.
For an Elite Screens contact and technical support in your area,
please visit www.elitescreens.com
②
①
Frame installed on
top bracket
1
Do not fasten the
screws on the
bottom bracket to
allow screen to
move up and down.
Frame installed on
bottom bracket