Elite Screens Osprey Tension Dual Series User manual

1
Rev.010612-AS
www.elitescreens.com [e-mail]
Tab-tensioned Dual Format Electric Projection Screen
Osprey Tension Dual Series
User’s Guide
All manuals and user guides at all-guides.com
all-guides.com

2
Rev.010612-AS
www.elitescreens.com [e-mail]
Make sure to read this user’s guide and follow the procedure below.
Caution: The Screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black
Top Drop in the roller. Please be a are of this as it ill void your arranty ith Elite Screens. Unapproved
changes or modifications (except for cutting the po er cord for hard ire installations) to this unit are
prohibited and ill void your arranty. For more information, please contact our Technical Support
Department at [phone] Ext. 604.
•Please retain this user’s guide for future reference.
•To avoid damaging the unit, do not use with any unauthorized accessories not
recommended by the manufacturer.
•Handle the unit carefully during transportation to avoid any damages.
•To ensure safe and reliable operation, direct connection to a properly grounded power
source is advised.
•The power outlet supplying power to the unit should be close to the unit and easily
accessible.
•Do not install the unit on uneven or inclined surfaces.
•Do not place any heavy objects over the power cord.
•Position the power cord properly to avoid creating a trip obstacle.
•To avoid an electrical shoc or fire, due to a loose contact or short circuit, do not
overload the power cord.
•The internal & external parts of this unit are not end user serviceable. Do not attempt to
disassemble this unit by yourself. No one except authorized technicians can open and
ma e repairs to this unit.
•Ma e sure the power source that this unit is connected to has a continuous power flow.
•If there is need to use an extension cord, ma e sure the cord has an equal rating as the
appliance to avoid over heat.
•Do not handle the power plug when your hands are wet or your feet are in contact with
water.
Do not use this unit under the following circumstances.
•Disconnect the power cord under the conditions of heavy rain, wind thunder or
lightning.
•Avoid direct sun light, rain shower and moisture.
•Keep away from fire sources and high temperature to prevent this device from
overheating.
•Cut off the power supply first before transportation or maintenance.
•To avoid possible injury and/or an electric shoc , do not attempt to use this screen if
there is obvious damage or if there are any evident bro en parts.
Important Safety & Warning Precautions
All manuals and user guides at all-guides.com

3
Rev.010612-AS
www.elitescreens.com [e-mail]
Due to various installation environments, the instructions provided in this user’s guide are for
reference only. Please consult a professional installation company for further installation and
safety advice. The installer must insure that proper mounting hardware is used to provide
adequate strength suitable for the installation. lite Screens is not liable for any faulty
installations. For limit adjustment instructions, please contact our Technical Support
Department at [phone] xt. 604.
The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black
drop in the roller. Please be aware of this as it will void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the warranty with the
manufacturer. Please contact Elite Screens Customer Service for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
owever, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures.
Reorient or relocate the receiving antenna of the device which may be casing the interference.
Increase the separation between the screen and the device’s receiver.
onnect the equipment into a different power outlet other than the device.
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with
foreign particles such as dust, sawdust, and/or liquids.
Regardless of the mounting method, the screen should be securely supported so that the vibration or
pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure
that the fasteners used are of adequate strength and suitable for the installation location.
Installation Warning
Pre-Installation
NOTE
All manuals and user guides at all-guides.com

4
Rev.010612-AS
www.elitescreens.com [e-mail]
Please make sure all accessories listed below are included before proceeding.
A. B. C.
IR Remote RF Remote 3 Way Wall Switch
Red+ Green-
D. E. F.
IR Eye Receiver AAA Batteries Bubble Level
Accessories for Osprey Tension Dual Series
All manuals and user guides at all-guides.com

5
Rev.010612-AS
www.elitescreens.com [e-mail]
The Osprey Tension Dual Series features the capability of alternating 16:9 DTV and 2.35:1 Cinemascope
projection screen formats, which are operated with the included Radio Frequency & Infrared Remote
Controls or the 3 Way Wall Switch. The dual motors and screen materials allow you to utilize both
formats. An Infrared sensor is not built into the case. The IR “Eye” Receiver must be connected to the RJ-
45 input to operate the screen with the Infrared Remote Control.
UP
2.35:1
16:9
UP
2.35:1
16:9
Radio Frequency Infrared 3 Way Wall Switch
1. Make sure the Osprey is plugged into a secure power source as shown below.
2. 2.35:1 Cinemascope: Press the 2.35:1 button on the Radio Frequency remote, Infrared remote
or the 3 Way Wall Switch to lower and display the 2.35:1 Cinemascope format.
Control System for Osprey Tension Dual Series
All manuals and user guides at all-guides.com