Celexon Manual Economy User manual

Operating instructions
celexon Electric Economy
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully
before connecting or operating this product. Please retain these instructions for future
reference.
Version: 32422_061

1
The purpose of these operating instructions is to familiarise you with the
operation of this product. Therefore, keep these instructions in a safe place so that you
can refer to it at any time.
• Before installation, please refer to the enclosed data sheet for further safety and use
instructions.
• Do not begin installation until you have read and understood the complete
operating instructions.
• Carry out the installation with another person to ensure safe installation.
• Remove the product from its packaging and remove all packaging material.
Make sure that there is no packaging material on or in the product. If you notice
any damage to the packaging, also check whether there is any damage to the
product. If you notice any external damage to the unit or any unexpected or
unusual functioning, the product must not be used any further. Immediately
contact the dealer from whom you purchased the product or celexon directly
(Web: www.celexon.co.uk, Mail: [e-mail]) for further information.
• To ensure trouble-free operation, the product may only be used indoors. It is NOT
suitable for outdoor use.
• The use of the appliance and accessories is forbidden to children under 16 years of
age.
• Ensure that no children play with the appliance or are in the vicinity without
supervision.
• Conversion or modication of the product impairs product safety.
• Caution: Risk of injury! Never open the product without authorisation. Never carry
out repair yourself!
• Do not use the product near gas or water appliances or in a dusty environment.
• Handle the product with care. It can be damaged by knocks, blows or falling from
even a small height.
• Keep the product away from moisture and heat.
• Never immerse the product in water or other liquids.
• Use the product only in its intended manner. Use for any other purpose may damage
the product or its surroundings.
• Tighten the screws, but do not overtighten them. Overtightening the screws (e.g.
by using a cordless screwdriver) can cause damage and affect the secure hold of
the screen.
• Suspended loads must be checked for strength and load-bearing capacity at least
WARNINGS

2
twice a year.
• Children should not use the screen or play under it unsupervised.
• Caution: Risk of injury! The unit closes ush and rmly in its retracted state, keep
ngers, hands or other small parts away from the opening.
• All supply lines and cables must not be subjected to additional loads and must be
laid in such a way that they are not damaged or crushed.
• Failure to observe the above instructions may result in personal injury and damage
to the product or equipment connected to it. Incorrect installation or use may also
invalidate the warranty.
• If you are unsure about the use of the product, please contact specialist personnel,
your dealer or celexon directly (Web: www.celexon.co.uk, Mail: [e-mail]).
• Technical changes and errors expected.
The manufacturer accepts no responsibility for damage to property or personal injury,
if the screen is used outside the recommended specications, or in the event of improper
installation. Do not use this screen in the vicinity of heaters or air conditioners. Also, do
not mount the product in direct sunlight or in front of a window. Due to the tempera-
ture-sensitive PVC surface, the projection screen fabric may be permanently damaged.
We recommend that you wait approx. 2 hours after delivery before installing the projec-
tion screen. This way you will allow the screen to acclimatise, especially when moving
from a cold to a warm environment (or vice versa).
Please avoid any stains on the surface of the screen. These may not be able to be remo-
ved
The positions of the end points are already optimally set at the factory and should not be
changed. Especially with electric screens, the entire length of the fabric should always be
used in order to achieve the best atness. An adjustment of a few cm of the end points
should only be made by persons with specialist knowledge and in consultation with the
manufacturer. Incorrect adjustment can result in damage to the projection surface.

3
Voltage: 100 V ~ 120 V, 60 Hz
220 V ~ 240 V, 50 Hz
Consumption: 130 W (MAX)
0,4 W (Standby)
Control: External infrared control box with
remote control
TECHNICAL DATA
DISCLAIMER
The information in this document is subject to change without notice by the
manufacturer. Changes will be added to subsequent versions of this manual.
Errors expected.
CARE INSTRUCTIONS
NEVER clean the screen with alcohol or other cleaning agents containing sol-
vents.Use only a soft and clean cloth. If necessary, dirt can be removed from
the surface with a mild soap solution (max. 5%). It is essential to avoid contact
with pointed or sharp objects. These could permanently damage the projecti-
on screen fabric. Further instructions can be found in the enclosed projection
screen instructions.

4
IN THE BOX
Attach the eyelets to the two side caps and measure the distance between
them. Mark the points on the ceiling and make sure that the eyelets are aligned
with each other and parallel to the wall. Pre-drill the holes at the markings with
the right diameter drill bit for the hooks and mounting material,  x them to the
ceiling and hang the screen.
* Electric Economy screen with a cloth width greater / equal
240 cm can only be mounted on the ceiling via eyelets. The
eyelets are already integrated in the metal side cap as a hole.
Here, ring eyelets and snap hooks are required.Make sure that
the mounting materials are suf cient for the load!
MOUNTING ON THE CEILING (VIA EYELETS)*
1x Screen 4x Plastic dowels 4x Screws 1x IR remote control incl.
Batteries
INSTALLATION NOTES
Install the screen in a position that is fully visible to all viewers! The optimum
installation height corresponds to the position of the viewers in the centre of
the screen with the screen fabric extended: eye level = lower third of the screen
surface.
The screen can be installed on the wall/ceiling or hung from the ceiling on clo-
sed ring eyelets plus screwable karabiners (the eyelets are already on the side
cap). For wall or ceiling installation only, the eyelets should be removed in ad-
vance). Please make sure that the metal shims are also used for wall and ceiling
mounting, otherwise safe installation cannot be guaranteed). The enclosed ins-
tallation material is intended for a solid stone wall. If necessary, obtain suitable
mounting material for your installation surface.
4x nut 2x suspension loops

5
MOUNTING ON THE CEILING (SCREWED)*
Measure the distance between the ho-
les in the side caps (two per cap) and
transfer them to the ceiling. Drill the
holes at the markings with the right
diameter drillbit for the diameter of the
mounting material, insert and screw
the screen in place tightly. Make sure
that the holes are parallel to the wall!
Use dowels and screws suitable for
your mounting surface.
Caution: Do not overtighten the
screws! If you notice cracks in the caps
they must be replaced! The screen
must not be used with cracked caps.
Please ensure that the metal plates are
also used for wall and ceiling mounting,
otherwise a safe installation cannot be
guaranteed).
* Electric Economy series screens with a cloth width greater / equal 240 cm
can only be mounted on the ceiling via eyelets.

6
Measure the distance between the ho-
les in the side caps (two per cap) and
transfer them to the wall.
Drill the holes at the markings with the
holes with the right diameter for the
mounting material and make sure that
the drill holes are absolutely level (Use
a spirit level!).
MOUNTING ON THE WALL
Use dowels and screws that are suitab-
le for your mounting surface. Screw the
two upper screws into the wall most of
the way and hang the screen from both
sides into the upper hole.*
Make sure that the screen is installed
straight and level. Tighten the screws
and then tighten the lower screws on
both sides of the screen.
Caution: Do not overtighten the
screws! If you notice cracks in the caps
they must be replaced! The screen
must not be used with cracked caps.
Please ensure that the metal shims are
also used for wall and ceiling mounting,
otherwise a safe installation cannot be
guaranteed).
* Electric Economy series screens with a cloth width greater / equal 240 cm:
Tighten the screws - the installation is now complete.

7
OPERATION
STEP 1: SAFETY CHECK (FIG. 1)
STEP 3: RETRACT SCREEN (FIG. 3)
Insert the plug into the socket (ensure correct voltage). The cable must not be
laid on hot surfaces or stretched. When using an extension make sure it has
the correct speci cation. The wall control box must be mounted with the cable
outlet on the underside.
Press the arrow key pointing upwards.
The screen retracts and stops auto-
matically at the housing or the set up-
per end point. Make sure that no ob-
jects or persons obstruct the retraction
of the screen.
CONTROL VIA THE WALL CONTROL BOX
Press the downward pointing arrow
button. The screen extends and stops
automatically at the set end point.
Make sure that no objects or persons
obstruct the extension path of the
screen.
STEP 4: STOP THE SCREEN
To stop the screen manually, press the stop button between the arrows.
STEP 2: EXTEND THE SCREEN (FIG. 2)

8
CONTROL VIA THE REMOTE CONTROL
STEP 1: SAFETY CHECK (FIG. 1)
Insert the plug into the socket (ensure correct voltage). The cable must not be
laid on hot surfaces or stretched. When using an extension make sure it has the
correct speci cation.
The wall control box must be mounted with the cable outlet on the underside.
STEP 3: RETRACT THE SCREEN (FIG. 3)
Press the upward pointing arrow but-
ton. The screen retracts and stops au-
tomatically at the housing or the set
upper end point.
Make sure that no objects or persons
obstruct the retraction of the screen.
STEP 2: EXTEND THE SCREEN (FIG. 2)
Press the downward pointing arrow
button. The screen extends and stops
automatically at the set end point.
Make sure that no objects or persons
obstruct the extension path of the
screen.
STEP 4: STOP THE SCREEN
To stop the screen manually, press the stop button between the arrows.
It is possible to set the stop points. Please request the instructions for this procedure from
your specialist dealer or directly via www.celexon.com

9
Manufacturer: celexon Europe GmbH
Address: Gutenbergstraße 2, 48282 Emsdetten, DE
Product name: celexon Electric Economy
Products that are marked with the CE mark meet all requirements of the relevant
EU directives. The EU declaration of conformity can be downloaded from the
following address: www.celexon.de/zertikate
INFORMATION ON EU CONFORMITY
The symbol indicates the separate collection of electrical and electronic
devices in EU countries. Please do not throw the device into household
waste. Find out about the return system applicable in your country and
contact your local authority or your local waste and pollutant collection
point if you have any questions about the disposal process.

10
Manufacturer: celexon Europe GmbH
Address: Gutenbergstraße 2, 48282 Emsdetten, DE
Product name: celexon Electric Economy
Products that are marked with the UKCA mark meet all requirements of the
relevant UK directives. The UK declaration of conformity can be downloaded
from the following address: www.celexon.de/zertikate
INFORMATION ON UK CONFORMITY
The symbol indicates the separate collection of electrical and electronic
devices in EU countries. Please do not throw the device into household
waste. Find out about the return system applicable in your country and
contact your local authority or your local waste and pollutant collection
point if you have any questions about the disposal process.