Elk Products Magic Module Series User manual

Instructions Printed On Inside
[phone] Voice
[phone] Fax
http://www.elkproducts.com
email: [email protected]
PO Box 100 • Hwy. 70W • Hildebran, NC 28637 • USA
Programs can be written and stored in non-volatile
EEProm memory using the ELK-MK400S Develop-
ment Kit.Typical Applications include: Program-
mable Delay Timer, Alarm Memory, Single Zone
Security System, Cross Zoning, Access Control,
PulseStretcher,PulseCounter,SwingerShutdown.
FEATURES:
•Two Digital Inputs
•Two Form C Relay Outputs
•Four Timers, 1/10th Sec. - 255 hours
•Four General Purpose Counters, 0 - 255
•Non-volatile EEProm Memory
•LED Output Indicators
SPECIFICATIONS:
•Compact Enclosure Size: 4.5" x 3" x 1.2"
•Operating Voltage: 9.6-15 Vdc
•Current Required: 70 mA
•Relays, 12 Amps @ 28VDC or 120VAC
REQUIRES:
•12 Vdc Power Supply
•Optional:Starter Development Kit(ELK-MK400S)
Features and Specifications subject to change without notice
PRINTEDINUSA L353 3500
For more information contact your local Distributor or:
ELKPRODUCTS,INC [phone] FAX[phone]
http://www.elkproducts.com Email:[email protected]
TwoInput,TwoOutput
Programmable Module
Notice:Itisrecommendedthattheentiresystembecompletelytestedona
regularbasis.However,despitefrequenttesting,anddueto,butnotlimitedto,
criminaltamperingorelectricaldisruption,itispossibleforthisproducttofailto
performasexpected.
Anysystemofanytypemaybecompromiseddeliberatelyormayfailtooperate
asexpectedforavarietyofreasons.
Magic Module Series
ELK-MM220
Magic Module Series
ELK-MM220
Two Input, Two Output
Programmable Module
Magic Module™Series
ELK-MM220 Module, 2 Input, 2 Output, Programmable
ELK-MM220S Module, Savoy Version of the ELK-MM220
ELK-MM443 Module, 4 Input, 4 Output, Programmable
ELK-MM443S Module, Savoy Version of the ELK-MM443
ELK-MV120 Voice Module, 32 Recordable Channels
ELK-MK400S StarterKit,IncludesELK-MM443S&ELK-MK485
ELK-MK485 ProgrammersKit,ELK-MB485,Cables,Software
ELK-MK420 iButton™AccessKitw/MM443,MA100,MA101
ELK-MA100 iButton™"Touchkey" Reader & Interface Pack
ELK-MA101 iButton "Touchkeys", 10 pcs w/keyring holders
ELK-MA290 Proximity / Wiegand Data Interface to MM443
ELK-MB485 DataBusInterface,RS232-RS485PCInterface
ELK-MC100 Clock / Calendar Module for ELK-MM443
ELK-MT100 TemperatureSensorModuleforELK-MM443
ELK-MK410 X-10®TransceiverKit,ProgrammedELK-MM443
4K Programmable Memory
APPLICATION:
The ELK-MM220 is an economical stand alone
field programmable controller. It can be pro-
grammedandused in avastarray ofapplications.
It features two digital inputs, two form C relay
outputs.
LIFETIME LIMITED WARRANTY
Elk Products, Inc. (“Manufacturer”) warrants to the original purchaser (the “Customer”)
that the products it manufactures (“Product”) shall be free from defects in material and
workmanship at time of shipment. Manufacturer’s obligations under this Limited
Warranty shall be limited to repairing or replacing, at its option, free of charge, any
product returned to Manufacturer freight prepaid. Manufacturer shall have no obligation
under this Limited Warranty or otherwise if (1) the Product has been damaged by
negligence, accident, mishandling, lightning or flood, or other Acts of God, (2) the
Product has not been operated in accordance with its operating instructions, (3) the
Product has been altered or repaired by anyone outside Manufacturer’s authorized
facilities (4) adaptations or accessories have been made or attached to the Product
which, in Manufacturer’s sole determination, have adversely affected its performance,
safety or reliability. Products such as batteries and fused transformers have their own
warranties, and are not included in this Limited Warranty.
If a Product should malfunction or fail, contact Manufacturer or one of its authorized
distributors for a Return Authorization (RA) number. Returned Products must include
a complete description of the problem, along with the RA number clearly marked on
outside of the package. Manufacturer will not be responsible for any unnecessary
items included with any returned Product.
THIS WARRANTY IS THE EXCLUSIVE WARRANTY FOR ANY PRODUCT. MANU-
FACTURER SPECIFICALLY DISCLAIMS ANY AND ALL OTHER WARRANTIES OF
ANY KIND, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF FITNESS
FOR A PARTICULAR PURPOSE OR OF MERCHANTABILITY. MANUFACTURER
SHALL NOT BE LIABLE IN TORT, INCLUDING NEGLIGENCE OR STRICT LIABILITY,
AND SHALL HAVE NO LIABILITY AT ALL FOR INJURY TO PERSONS OR PROP-
ERTY. MANUFACTURER’S LIABILITY FOR FAILURE TO FULFILL ITS OBLIGATION
UNDER THIS LIMITED WARRANTY OR ANY OTHER LIABILITY IN CONNECTION
WITH A PRODUCT SHALL BE LIMITED TO THE AMOUNT OF THE PURCHASE PRICE
RECEIVED BY MANUFACTURER FOR THE PRODUCT. THE REMEDIES STATED IN
THIS LIMITED WARRANTY ARE THE CUSTOMER’S EXCLUSIVE REMEDIES
AGAINST MANUFACTURER REGARDING ANY PRODUCT. UNDER NO CIRCUM-
STANCES SHALL MANUFACTURER BE LIABLE FOR ANY INDIRECT, INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING LOST PROFITS AND REV-
ENUES, INCONVENIENCE OR INTERRUPTIONS IN OPERATIONS, OR ANY OTHER
COMMERCIAL OR ECONOMIC LOSSES OF ANY KIND. THESE LIMITATIONS AND
DISCLAIMERS ARE NOT MADE BY MANUFACTURER WHERE PROHIBITED BY
LAW. SOME STATES PROHIBIT LIMITATIONS OF WARRANTIES AND THE CUS-
TOMER MAY HAVE ADDITIONAL RIGHTS IN THOSE STATES.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation. NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna. 2) Increase the separation between
the equipment and receiver. 3) Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. 4) Consult the dealer or an
experienced radio/TV technician for help.

ELK-MM220 HOOK-UP DIRECTIONS
The ELK-MM220 has been factory programmed with a sample application as labeled on
the unit, for other applications it must be reprogrammed before installation. The Program
DevelopmentKit(ELK-MK400S)isrequiredtore-programtheELK-MM220ifdesired.TheDevelop-
mentKitcontainssoftwareandprogramminginstructionsneededtoprogramtheELK-MM220.The
programis written usingthe Elk MagicModule Software anddebugged by usingthe ELK-MM443
Magic Module that is included in the development kit. The program is then download into the ELK-
MM220througha5conductorribboncableconnectedbetweentheELK-MM443J1 connectorand
theELK-MM220J5connector.Note:IfusingtheClock/CalendarModule(ELK-MC100),temporarily
remove it to gain access to the ELK-MM443 J1 connector.
The ELK-MM220 has two digital inputs that switch from Low to High at approximately 2 Volts. Each
input is jumper selectable at J1 & J2 for an onboard 2K input resistor either pulled up to +12 Volts,
or pulled down to Ground. The ELK-MM220 has two form C relay outputs. Relay 2 is jumper
selectable using J3 to switch the output through a transistor (100mA max). Placing J3 to the OUT
position will disable Relay 2 and allow the Relay 2 COM terminal to be pulled to ground through a
transistorwhen activated. Thissettinghandles up to100mAof current andis intended forapplica-
tions like flashing an LED. If more current or dry contacts are required then set J3 to IN and use the
Relay 2 contacts, the transistor will be disabled.
TesttheELK-MM220afterdownloadingtheprogramtoensurethat it functions as desired. The
ELK-MM220canbereprogrammedmultipletimes.
*TheELK-MM220SversionisrequiredifusingSavoyAutomationSoftware.
GND
To Input Circuitry
+12 VDC
2K
Normally Closed
Opens from
Ground
Input HookupTypes for IN1 and IN2
INx
2
OUTPUT
ELK-MM220
PROGRAMMER 1
NO COM NCNO COM NCIN1 IN2 NEG+12V NEG
RELAY 2RELAY 1
J1 J2
INPUT 2
SELECT
J3
+12V
GND
INPUT 1
SELECT
RELAY 2
OUT IN
J5
D4 D3
MM220
will see a
Low to Hi
when
Switch
Opens
J1 or J2
NEG
GND
Input
Jumper
is set to
+12V
GND
To Input Circuitry
+12 VDC 2K
Normally Closed
Opening switch will
trip this input
INx
MM220
will see a
Hi to Low
when
switch
Opens
J1 or J2
NEG
GND
Input
Jumper
is set to
GND
+2 to 12 Volts DC
GND
To Input Circuitry
+12 VDC 2K
Normally Open
Closes to
Ground
INx
MM220
will see a
Hi to Low
when
Switch
Closes
J1 or J2
NEG
GND
Input
Jumper
is set to
+12V
GND
To Input Circuitry
+12 VDC 2K
Normally Open
ClosingSwitchto
2to12VoltsDC
will trip this input
INx
MM220
will see a
Low to Hi
when
Switch
Closes
J1 or J2
NEG
GND
Input
Jumper
is set to
GND
+2 to 12 Volts DC
+12 Volt DC Power Supply
ELK-624 Recommended
+
-
N.O. N.C.
ALARM
SWITCHES
12 VOLT
SIREN
(ELK-45)
+
-
IN1 is a Momentary Key Switch, IN2 is a Normally Closed Burglar Loop, Relay 1 is the Alarm Output, Relay 2 is the Status LED
1K
J3 is shown with
Relay 2 out of ciruit,
the COM terminal will
be pulled to ground
when output 2 is
activated
(100ma Max)
LED
RELAYS
ACTIVE
LEDS
+
-
+
-
+12V position pulls up
IN1 or IN2 through a
2K resistor
GND position pulls
down IN1 or IN2
through a 2K resistor
+
Example Hookup: ELK-MM220 used as a Single Zone Security System
JUMPERS J1, J2 ,J3 are
located under cover
MOMENTARY
KEY SWITCH