Elkay ECDFPW Instructions for use

97749C (Rev. J - 7/07)
ECDFPW314C ECDFPWVR314C
Installation/Care/UseManual
Soft Sides™Fountains with FLEXI-GUARD®
Toassureyouinstallthismodeleasilyandcorrectly,
PLEASEREADTHESESIMPLEINSTRUCTIONSBEFORESTARTINGTHE
INSTALLATION.CHECKYOURINSTALLATIONFORCOMPLIANCEWITH
PLUMBING,ELECTRICALANDOTHERAPPLICABLECODES.Afterinstallation,leave
theseinstructionsinsidethefountainforfuturereference.
IMPORTANT! INSTALLER PLEASE NOTE.
THEGROUNDINGOF ELECTRICALEQUIPMENTSUCH ASTELEPHONE,COMPUTERS, ETC.TO
WATERLINESISACOMMONPROCEDURE.THISGROUNDINGMAYBEINTHE BUILDINGORMAY
OCCURAWAYFROMTHEBUILDING.THIS GROUNDINGCAN CAUSEELECTRICALFEEDBACK
INTOAFOUNTAIN,CREATINGANELECTROLYSISWHICHCAUSESAMETALLICTASTE ORAN
INCREASEINTHE METALCONTENTOFTHEWATER.THISCONDITION ISAVOIDABLEBYUSING
THEPROPER MATERIALSASINDICATED.ANYDRAIN FITTINGSPROVIDED BYTHEINSTALLER
SHOULDBEMADEOFPLASTICTOELECTRICALLYISOLATETHE FOUNTAINFROMTHEBUILDING
PLUMBINGSYSTEM.
IMPORTANT
ALLSERVICE TOBEPERFORMED BYAN AUTHORIZED SERVICEPERSON
FIG. 2FIG. 1
ECDFPW314C
Installer
NOTE: WATER FLOW
DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY

97749C (Rev. J - 7/07)
ECDFPW314C ECDFPWVR314C
FIG. 3
PAGE 2
LEGEND
A= RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED
COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM WALL SHUT
OFF BY OTHERS
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN
C=1-1/4"DRAINFURNISHED
D = OPENING FOR OPTIONALAP-99ACCESS PANEL.
NOTE:REINFORCE THE WALLIN THESHADEDAREAS
ECDFPW314C

97749C (Rev. J - 7/07)
ECDFPW314C ECDFPWVR314C
PAGE 3
INSTALLATIONINSTRUCTIONS
1. Wall should already be framed for the fountain using the positioning dimensions shown in Figure 3. Shown
dimensions pertain to installation location (framing must support up to 300 lbs. weight). These dimensions
are required for compliance with ANSI Standard A117.0.
2. Attach wall plate assembly to wall as shown in Figure 3 using 5/16" x 2" long bolts and flat washers
(not provided). Tighten securely. (Fastener must match wall type, i.e. lag screws for wood studs, bolts and
anchors for masonary construction.)
3. Install back panel. Place the upper edge of the panel above hanger on the wall. Slide panel down until it
engages the hanger. Be sure back panel is firmly engaged before releasing it.
4. Install rough-in plumbing as shown in Figure 3. Waste line should extend a minimum of 2" (51mm) thru the
back panel. Run supply water inlet line thru back panel. Install a service stop (not provided). Turn on supply
water and flush thoroughly.
5. Remove bottom access panel from fountain basin and save the screws. Install the fountain to the back
panel using (4) 5/16" x 3/4" long screws and washers (provided) thru holes in back panel. Tighten securely.
6. Cut waste tube to required length using plumbing hardware and a trap (not provided) as a guide. Install
hardware and trap. Tighten securely.
7. Make water supply connections from service stop to the 3/8" O.D. unplated copper tube coming out of the
fountain strainer (See Fig. 1). Turn on water supply and check for leaks. Newly installed water supply line
should be insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER
ASDAMAGE TOTHE O-RINGSMAYRESULT.
8. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above
105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting these products to supply line pressure lower than 20 PSIG or higher than 105 PSIG is not
covered by warranty.
9. Check stream height from bubbler. Stream height is factory set at 35 PSI. If supply pressure varies greatly
from this, adjust the screw on regulator item 10 by using a small screwdriver through the small hole
in the push button item 3 (See Fig.5). Clockwise adjustment will raise stream height and counter-clockwise
adjustment will lower stream height. For best adjustment stream should hit basin approximately 6-1/2"
(165mm) from bubbler.
10. Replace bottom access panel to fountain basin using screws provided. Tighten securely.
TROUBLESHOOTINGANDMAINTENANCE
1. Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits
may be removed from orifice with a small round file not over 1/8" diameter or a small diameter wire.
CAUTION: Do not file or cut orifice materials.
2. Stream Regulator: If orifice is free of material deposits, regulate flow according to instruction 9 stated above.
3. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an
o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar while
pulling on the tubing (See Figure 2). To insert tubing, push tube straight into the fitting until it reaches a
positive stop, approximately 3/4".

97749C (Rev. J - 7/07)
ECDFPW314C ECDFPWVR314C
PAGE 4
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL1.800.323.0620
ELKAYMANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL60523 • 630.574.8484
PARTNO.ITEMNO. PARTSLIST
Drain-Strainer
RetainingNut
PushButton
PushButtonSleeve
RegulatorHolder
OrificeAssy
HousingAssy
Pedestal
BubblerLocknut
Regulator
CapScrew
Screw-#10-24 X .50PHTC
Strainer
FountainArm- Long
BottomCoverPlate-Long
BackPanel
HexNut
RegulatorMountingBracket
Gasket(VRModel Only)
Bubbler-Nipple(VR Model Only)
Bubbler(VRModel Only)
PolyTubing (CutTo Length)
MountingPlateAssy
DrainTailpipe
DrainAdapter
Gasket-TailPipe
Tube-Water In
Nut-RegulatorMounting
Washer-Flat .339/.359IDSteel
Screw-Mach. 5/16-18x3/4
40575C
15005C
45662C
45737C
50986C
40322C
56011C
55997C
75580C
61313C
75672C
112627543890
55996C
28790C
55000665
28290C
40045C
28291C
100322740560
15009C
45392C
56092C
28286C
45679C
45805C
50074C
60295C
45736C
75541C
111577243890
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
DESCRIPTION
FIG. 8
NOTE: WHEN INSTALLING REPLACEMENT
BUBBLER AND PEDESTAL, TIGHTEN NUT
(ITEM 9 OR 20) ONLY TO HOLD PARTS SNUG
IN POSITION. DO NOT OVER TIGHTEN.
FIG. 6
17 210 5
34
18
14
SEE FIG. 6 OR 7 16
SEE
FIG.5
15 1,24,25,26
13
7
8
9
6
FIG. 5
19
20
21
FIG. 7
22
23
27
28
29, 30
12
11