Elkay 4405BFFR User manual

PAGE 1
4405BFFR_FTN_A LK4405BFFR_FTN_A
1000003941 (Rev. D - 03/20)
Owners Manual
Model 4405BFFR
Bottle Filling Freeze Resistant Wall Mounted Tubular Fountain
4405BFFR Fountains are among the easiest to install Fountains on the market today. To assure you install
these models easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE
INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND ALL
OTHER APPLICABLE CODES. After installation, leave these instructions with the Fountain for future reference.
This Freeze Resistant Fountain is shipped in two separate cartons. The second carton contains the Freeze Resistant
Package that are installed on an interior heated wall. The interior space must maintain a minimum temperature of
50° F (10° C). Refer to the Freeze Resistant Package for the rough-in dimensions for installation.
Installer
FINISHED FLOOR
6"
152mm
8"
203mm
7"
178mm
9"
229mm
O1/2"
13mm (4 PL)
1/8"
3mm 19 1/8"
486mm
10"
254mm
O
14 9/16"
371mm
3"
76mm
A
B
27 1/8"
689mm
37 1/8"
943mm
57 1/8"
1451mm
28 3/4"
731mm
1-1/4" DRAIN
32mm
26 1/8"
664mm

PAGE 2
4405BFFR_FTN_A LK4405BFFR_FTN_A
1000003941 (Rev. D - 03/20)
The freeze resistant package must be mounted on an interior wall in a heated area. The room temperature of the
interior heated area must be 50° F (10° C) or higher. The freeze resistant package may be surface or recessed
mounted. If recess mounted the surface of the cover must be ush with the interior wall surface. The package is
furnished with screws for mounting the cover to the box. If the box is recess mounted, do not fasten the top and
bottom of the cover to the box. Use the holes on the front only.
1. Assemble the operating cable to the fountain bracket. (Fountain should be mounted to exterior wall.) The
adjustment nuts should be in the middle of threaded area on the operating cable. See Figure 5. Create a loop in
the cable and thread the free end of the cable through the wall into the freeze resistant box.
2. Connect free end of operating cable to the valve-operating bracket in the freeze resistant box.
3. Remove cable free play by adjusting the jam nuts on the ends of the operating cable. See Figure 4.
4. Connect water line from bottle ller nozzle into freeze resistant box. The connection to the box uses a quick connect
water tting. Position the water line, in the fountain, to drain back into interior mounted box. Any water left standing,
in the exterior line, can freeze . See Fig. 7 To insert tubing, push tube straight into tting until it reaches a positive
stop. To remove tubing from the ttings, relieve water pressure, push in on dark gray collar while pulling out on the
tubing. See Figure 8.
5. Connect drain and water supply lines to the freeze resistant fountain. Refer to Figure 1 for component positions
Start-up
6. Turn on building water supply and check all connections for leaks. Repair as required.
7. Adjust operating cable as required. Cable system should have a minimal amount of free play to allow for proper
valve operation. If the system is too tight the valve will stay in the on position creating constant water ow. Too
much free play will result in non-operation of the valve with the push-buttons.
8. Note: Water from the drain back tube in the freeze resistant package, will continue to run while the valve is actuated.
9. After cable system is adjusted properly stu󰀨 exible insulation into any openings between the outside wall and the
interior box.
10. Recheck all connections. If all connections are leak free replace cover(s) on the freeze resistant box(es) and
fountain(s).
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE
BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN
ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE
WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN
FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE
FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
INSTALLATION INSTRUCTIONS

PAGE 3
4405BFFR_FTN_A LK4405BFFR_FTN_A
1000003941 (Rev. D - 03/20)
PUSH BUTTON CABLE
BC
D
A
FINISHED FLOOR
7" 178mm
10" 254mm
O
3" 76mm
26 1/8" 664mm 6" 152mm
3 1/2" 89mm 1 3/4"
44mm
29 1/8" 740mm
30 9/16" 776mm
1/8" 3mm 19 1/8"
486mm
7 1/4" 184mm
12 1/8" 308mm
4 5/8" 117mm
27 1/8" 689mm
ADA
REQUIREMENT
37 1/8"
943mm
14 9/16"
371mm
57 1/8" 1451mm
8" 203mm
12" 305mm MAX. WALL THICKNESS
2 5/8" 67mm
3 5/8" 92mm
13 11/16" 348mm
14 11/16" 373mm
18 3/16" 462mm
FINISHED FLOOR
LEGEND A = MOUNTING BOLT LOCATIONS (4)(1/2" DIA. NOT PROVIDED). B = 7/8" DIA. (22mm) HOLE FOR WATER SUPPLY TUBE. C = 7/8" DIA. (22mm) HOLE FOR OPERATING CABLE. D = 2" DIA. (51mm) HOLE FOR WASTE LINE.
FIG. 1 4405BFFR BOTTLE FILLING FREEZE RESISTANT FOUNTAIN
MOUNTING BOLT AND ACCESS HOLE LAYOUT
PUSH BUTTON CABLE
1/8" 3mm 19 1/8"
486mm
7 1/4" 184mm
12 1/8"
308mm
4 5/8" 117mm

PAGE 4
4405BFFR_FTN_A LK4405BFFR_FTN_A
1000003941 (Rev. D - 03/20)
PUSH BUTTON CABLE
BC
D
A
FINISHED FLOOR
7" 178mm
10" 254mm
O
3" 76mm
26 1/8" 664mm 6" 152mm
3 1/2" 89mm 1 3/4"
44mm
29 1/8" 740mm
30 9/16" 776mm
1/8" 3mm 19 1/8"
486mm
7 1/4" 184mm
12 1/8" 308mm
4 5/8" 117mm
27 1/8" 689mm
ADA
REQUIREMENT
37 3/16" 944mm
14 9/16"
371mm
57 3/16" 1452mm
8" 203mm
12" 305mm MAX. WALL THICKNESS
2 5/8" 67mm
3 5/8" 92mm
13 11/16" 348mm
14 11/16" 373mm
18 3/16" 462mm
FINISHED FLOOR
FIG. 2 4405BFFR BOTTLE FILLING FREEZE RESISTANT FOUNTAIN
ROUGH-IN DRAWINGS
1. Wall should already be framed for the fountain using dimensions shown in Fig. 1. Shown dimensions pertain to installation location. These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only). 2. Remove bottom cover from fountain and save screws. 3. Install the fountain using 3/8" minimum fasteners and washers (not provided). Tighten securely. 4. Prior to installing the bottle ller to the fountain, insert the drain tube (item #4) into the arm tunnel and adjust drain to lean to the left side of the arm when facing the button. Place the aesthetic collar (item #18) onto the mounting position of the fountain ensuring the vertical edge of the collar is upright and the curved edge sits below the mounting surface. Mount bottle ller to arm with collar centered between the two pieces. Install bottle ller to arm being sure drain tube is above mounting plate of ller. Install mounting hardware to secure ller to fountain. 5. Install bottle ller to fountain being sure drain tube is above mounting plate of ller. Install mounting hardware to secure ller to fountian. 6. Attach drain tube to fountain and cut to required length using the freeze resistant box as a guide. 7. Install freeze-resistant box - see box instructions.

PAGE 5
4405BFFR_FTN_A LK4405BFFR_FTN_A
1000003941 (Rev. D - 03/20)
FIG. 3
FIG. 4
CABLE SHEATH ADJUSTMENT
To Increase Free Play
To Reduce Free Play
FIG. 6 FIG. 7
FIG. 5
See Fig. 3
See Fig. 6

PAGE 6
4405BFFR_FTN_A LK4405BFFR_FTN_A
1000003941 (Rev. D - 03/20)
ITEM
NO.
PART NO.
ITEMIZED PARTS LIST
DESCRIPTION
1000003814*
45931C
1000003813*
66816C
75724C
45662C
45663C
98679C
98680C
98681C
1000003692
1000003693
28703C
28703C-LK
28091C-HT
98683C
98685C
98686C
98872C
75672C
97247C
1000005456
1
2
3
4
5
6
7
8
9
10
11
11a
11b
12
13
14
15
16
17
18
Cover - Round Plate
Outdoor Bottle Filler Drain Plug
Bottom Cover
Tube - Drain
Pinned Torx Screw - 1/4-20 x 3/4"
Push Button
Push Button Guide Sleeve
Kit - Nozzle
Kit - Aerator/Key
Kit - Blank Bottle Filler Trim
Kit - LK4405 Bottle Filler Trim
Kit - 4405 Bottle Filler Trim
Blank Nameplate Insert (only)
LK4405 Nameplate Insert (only)
4405 Nameplate Insert (only)
Kit - Plastic Drain
Kit - 4400 Series Hardware
Kit - Bottle Filler Waterway
Kit - Pivot Brkt/Bshing/Bumper/Rod/Tailpiece
Screw-Socket Cap
Kit - VR Torx Screws/Bit
Aesthetic Collar
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE.
PRINTED IN U.S.A.
Halsey Taylor – halseytaylor.com
Elkay – elkay.com
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL TECHNICAL SERVICES AT 1.800.834.4816
1333 BUTTERFIELD ROAD, DOWNERS GROVE, ILLINOIS 60515
*select color option to complete part number
*FINISH COLOR OPTIONS – Choose color option to
complete your model number, add as sux example:
4405BFFRKEVG
Matte nish: Evergreen = EVG
Gloss nish:
Beige = BGE Gray = GRY Terracotta = TER
Black = BLK Orange = ORN White = WHT
Blue = BLU Purple = PUR Yellow = YLW
Brown = BRN Red = RED
FIG. 8
SCALE:
DR. BY:
B
CKD. BY: APPROVED BY:
REL. ECN DATE:
MATERIAL:
TOLERANCES UNLESS OTHERWISE SPECIFIED:
DESCRIPTION
REV.
MANUFACTURING CO.
6400 PENN AVENUE SAVANNA, ILLINOIS 61074
This Print is the Property of ELKAY MANUFACTURING CO. and is
loaned subject to return upon demand and upon the express condition
that it is not to be used directly or indirectly without our permission for
purposes other than those for which it was furnished.
2 PLACE DECIMAL ± .03 1 PLACE METRIC ± .8 MM
3 PLACE DECIMAL ± .005 2 PLACE METRIC ± .1 MM
ANGLE S ±.50°
SCALE:
DR. BY:
B
CKD. BY: APPROVED BY:
REL. ECN DATE:
MATERIAL:
TOLERANCES UNLESS OTHERWISE SPECIFIED:
DESCRIPTION
REV.
MANUFACTURING CO.
6400 PENN AVENUE SAVANNA, ILLINOIS 61074
This Print is the Property of ELKAY MANUFACTURING CO. and is
loaned subject to return upon demand and upon the express condition
that it is not t o be used directly or indirectly without our permission for
purposes other than those for which it was furnished.
2 PLACE DECIMAL ± .03 1 PLACE METRIC ± .8 MM
3 PLACE DECIMAL ± .005 2 PLACE METRIC ± .1 MM
ANGLES ± .50°
PAGE 5
4420BF_FTN_A LK4420BF_FTN_A
1000003685 (Rev. C - 03/20)
13
19
14
17
2
15 23
14
15, 24
14
18
23
ARM ONLY 10
26
REV. DESCRIPTION
MATERIAL:
SCALE: CH. BY: APPROVED BY:
DR. BY:
REL. ECN: DATE:
B
6400 PENN AVENUE SAVANNA, ILLINOIS 61074
MANUFACTURING CO.
TOLERANCES UNLESS OTHERWISE SPECIFIED:
This Print is the Property of ELKAY MANUFACTURING CO. and is
loaned subject to return upon demand and upon the express condition
that it is not to be used directly or indirectly without our permission for
purposes other than those for which it was furnished.
2 PLACE DECIMAL ± .03 1 PLACE METRIC ± .8 MM
3 PLACE DECIMAL ± .005 2 PLACE METRIC ± .1 MM
ANGLES ±.50°
FOR REVISIONS
SEE SHEET 1 OF 10
SHEET 5 OF 10
SEE SHEET 1 OF 10
4420BFDB TUBULAR BI-LEVEL FOUNTAIN
1 : 8
CGK
CGK
D
21
27
38
62
31
21
11 24
22
27
13
10
42
62
49
30
10
13
42
62
61
28
63
20
29
6 SEE NOTE 13
58
78SEE NOTE 11
20
28
3748
21
16 59
10
13
1659
52 OR
33
25
43
43
43
61
16
3SEE NOTE 5
34
32 45
33 45
63
29 22 24
24
11
11
37
3748
48
52 OR
22
20
29
28
63
61
45
8SEE NOTE 13
NCR-02488
RDZ
5/1/17
ASY99052C
61
62
61
62
61
62
61
59
Vandal-Resistant Bubbler
FIG. 1
BASIN
12
4
1
21
4
3
20 25 20
22
9
6
15, 24
12
22
20
20
16
11
21
13, 17
3
4
15
6
7
16
15
11, 11a, 11b
12
13
18
10
8
2
9
14
13
14
14
14 1
5, 13