Elkay Soft Sides ECDFPW314C Instructions for use

97749C (Rev. M - 01/18)
ECDFPW314C ECDFPWVR314C
Page 1
Installation & Use Manual
Soft Sides®Fountains with FLEXI-GUARD®
To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR
INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER
APPLICABLE CODES. After installation, leave these instructions inside the fountain
for future reference.
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING
THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING
PLUMBING SYSTEM.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
FIG. 2FIG. 1
ECDFPW314C
Installer
NOTE: WATER FLOW
DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED COP-
PER TUBE CONNECT
COLD WATER SUPPLY
B CA
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
A B C
WWW.RESTROOMDIRECT.COM 704 • 937 • 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

97749C (Rev. M - 01/18)
ECDFPW314C ECDFPWVR314C
Page 2
12 1/2"
318mm
17 1/2"
445mm
3 3/16"
81mm
18"
457mm
5/8"
16mm
18 3/4"
476mm
C
A
B
19 3/4"
502mm
12 1/8"
308mm
20 3/8"
24"
610mm
CHILD ADA
REQUIREMENT
4 3/8"
111mm
9"
229mm
9"
229mm 9 7/8"
251mm
FINISHED FLOOR
1 5/8"
41mm
23 1/16"
586mm
6"
152mm
39 9/16"
1005mm
26 7/16"
672mm
25 3/16"
640mm
16"
406mm
1/2"
13mm
B
A
BACK PANEL
WALL PLATE
ASSEMBLY
1/4" (6mm) DIA HOLES FOR
MOUNTING PLATE TO WALL
3/8" (10mm) DIA HOLES
FOR MOUNTING PLATE
TO WALL (10)
10 3/8"
264mm
8"
203mm
8"
203mm D
5 1/4"
133mm
5 1/4"
133mm
8"
203mm
8"
203mm
FINISHED FLOOR
FIG. 3
LEGEND
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED
COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM WALL SHUT
OFF BY OTHERS
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN
C = 1-1/4" DRAIN FURNISHED
D = OPENING FOR OPTIONAL AP-99 ACCESS PANEL.
NOTE: REINFORCE THE WALL IN THE SHADED AREAS
ECDFPW314C
WWW.RESTROOMDIRECT.COM 704 • 937 • 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

97749C (Rev. M - 01/18)
ECDFPW314C ECDFPWVR314C
Page 3
INSTALLATION INSTRUCTIONS
1. Wall should already be framed for the fountain using the positioning dimensions shown in Figure 3. Shown
dimensions pertain to installation location (framing must support up to 300 lbs. weight). These dimensions
are required for compliance with ANSI Standard A117.0.
2. Attach wall plate assembly to wall as shown in Figure 3 using 5/16" x 2" long bolts and at washers
(not provided). Tighten securely. (Fastener must match wall type, i.e. lag screws for wood studs, bolts and
anchors for masonary construction.)
3. Install back panel. Place the upper edge of the panel above hanger on the wall. Slide panel down until it
engages the hanger. Be sure back panel is rmly engaged before releasing it.
4. Install rough-in plumbing as shown in Figure 3. Waste line should extend a minimum of 2" (51mm) thru the
back panel. Run supply water inlet line thru back panel. Install a service stop (not provided). Turn on supply
water and ush thoroughly.
5. Remove bottom access panel from fountain basin and save the screws. Install the fountain to the back
panel using (4) 5/16" x 3/4" long screws and washers (provided) thru holes in back panel. Tighten securely.
6. Cut waste tube to required length using plumbing hardware and a trap (not provided) as a guide. Install
hardware and trap. Tighten securely.
7. Make water supply connections from service stop to the 3/8" O.D. unplated copper tube coming out of the
fountain strainer (See Fig. 1). Turn on water supply and check for leaks. Newly installed water supply line
should be insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER
AS DAMAGE TO THE O-RINGS MAY RESULT.
8. These products are designed to operate on 20-105 PSI supply line pressure. If inlet pressure is above
105 PSI, a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting these products to supply line pressure lower than 20 PSI or higher than 105 PSI is not
covered by warranty.
9. Check stream height from bubbler. Stream height is factory set at 35 PSI. If supply pressure varies greatly
from this, adjust the screw on regulator item 10 by using a small screwdriver through the small hole
in the push button item 3 (See Fig.5). Clockwise adjustment will raise stream height and counter-clockwise
adjustment will lower stream height. For best adjustment stream should hit basin approximately 6-1/2"
(165mm) from bubbler.
10. Replace bottom access panel to fountain basin using screws provided. Tighten securely.
TROUBLE SHOOTING AND MAINTENANCE
1. Orice Assy: Mineral deposits on orice can cause water ow to spurt or not regulate. Mineral deposits
may be removed from orice with a small round le not over 1/8" diameter or a small diameter wire.
CAUTION: Do not le or cut orice materials.
2. Stream Regulator: If orice is free of material deposits, regulate ow according to instruction 9 stated above.
3. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an
o-ring water seal. To remove tubing from the tting, relieve water pressure, push in on the gray collar while
pulling on the tubing (See Figure 2). To insert tubing, push tube straight into the tting until it reaches a
positive stop, approximately 3/4".
WWW.RESTROOMDIRECT.COM 704 • 937 • 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

97749C (Rev. M - 01/18)
ECDFPW314C ECDFPWVR314C
Page 4
PART NO.ITEM NO.
PARTS LIST
Kit - Drain Strainer/Gasket
Kit - Regulator/Holder/Nut
Push Button
Push Button Sleeve
Screw - Mach. 5/16-18 x 3/4
Kit - Flexi Bubbler
Washer - Flat .339/.359ID Steel
Nut-Regulator Mounting
Drain Adapter
Drain Tailpipe
Cap Screw
Screw - #10-24 X .50 PHTC
Strainer
Fountain Arm - Long
Bottom Cover Plate - Long
Back Panel
Hex Nut
Regulator Mounting Bracket
Mounting Plate Assy
Poly Tubing (Cut To Length)
Kit - Bubbler (VR Model Only)
Edge Trim - 2FT.
98924C
98530C
45662C
45737C
111577243890
56073C
75541C
45736C
45805C
0000000930
75672C
112627543890
55996C
28790C
55000665
28290C
40045C
28824C
28286C
56092C
97446C
56369C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
NS
DESCRIPTION
FIG. 8
NOTE: WHEN INSTALLING REPLACEMENT
BUBBLER AND PEDESTAL, TIGHTEN
LOCKNUT ONLY TO HOLD PARTS SNUG IN
POSITION. DO NOT OVER TIGHTEN.
FIG. 6
17 222
34
18
14
SEE FIG. 6 OR 7
16
SEE
FIG. 5
15
1, 9, 10
13
FIG. 5
FIG. 7
20
19
20
8
5, 7
12
11
29
29
9
BASIN
21
5
Locknut
BASIN
NS = NOT SHOWN
BUBBLER DETAIL VANDAL RESUSTENT
BUBBLER DETAIL
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
WWW.RESTROOMDIRECT.COM 704 • 937 • 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115