Elkay EDF214WC Installation manual

Page 1 96917C (Rev. D - 02/18)
EDF214WC
Installation/Care/Use Manual
Model: EDF214WC
Non-Refrigerated Fountain
To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION
FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE CODES.
After installation, leave these instructions inside the fountain for future reference.
Installer
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO
A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE
IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER
MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE
OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
TUBE IS
SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
FIG. 2
OPERATION OF QUICK CONNECT FITTINGS
FIG. 1
NOTE: WATER FLOW
DIRECTION
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED COP-
PER TUBE CONNECT
COLD WATER SUPPLY

96917C (Rev. D - 02/18)
EDF214WC
Page 2
FIG. 3
FINISHED FLOOR
DETAIL 1
LEGEND: A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN C = MOUNTING HOLES FOR SECURING FOUNTAIN TO WALL

Page 3 96917C (Rev. D - 02/18)
EDF214WC
1. Wall should already be framed for the fountain using the positioning dimensions shown in Fig 3. Shown
dimensions pertain to installation location (framing must support up to 150 lbs. weight).
2. Install rough-in plumbing as shown in Fig 3. Run supply water inlet line and connect to a service stop (not
 provided).Turnonsupplywaterandushthoroughly.Closewatersupply.
3. Remove bottom access panel from fountain basin and save the screws. Install the fountain to the wall using
(4) 5/16" bolts and washers (not provided). Bolts should be long enough to securely fasten the fountain to the
wall. Tighten securely, but do not over tighten. Over tightening will crack the Composite Fountain.
4. Remove elbow from end of p-trap (item 1) and attach it to drain tube. Re-attach elbow to p-trap and cut
waste tube to required length using plumbing hadware and trap as guide.
5. Make water supply connections from service stop to the fountain strainer (item 14) by inserting the water
inlet line into the inlet side of strainer until it reaches a positive stop about 3/4", (See Fig 1, Page 1). Turn on
water supply and check for leaks. Newly installed water supply line should be insulated after leak check is
completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE O-RINGS
MAY RESULT.
6. These products are designed to operate on 20-105 PSI supply line pressure. If inlet pressure is above 105
PSI, a pressure regulator must be installed in the supply line. Any damage caused by reason of connecting
these products to supply line pressure lower than 20 PSI or higher than 105 PSI is not covered by warranty.
7. Check stream height from bubbler. Stream height is factory set at 45-50 PSI. If supply pressure varies
greatly from this, remove items Button and Cover (See Fig 5, Page 4) and adjust the screw on regulator item
10. Clockwise adjustment will raise stream height and counter-clockwise adjustment will lower stream height.
For best adjustment stream height should be approximately 1" (25mm) above the bubbler guard. (See Fig 4,
Page 4).
8. Replace bottom access panel to fountain basin using screws provided. Tighten securely.
INSTALLATION INSTRUCTIONS
Care and Maintenance of Elkay Fountains
The Elkay fountain provides an exremely durable, nonporous surface which resists staining. Care is very simple.
Routine cleaning with a soft sponge or cloth, or with water or non-abrasive aerosol foam cleaner, is all that is
normally needed to give many years of trouble free service. Cleaners left standing on the fountain surface can
dullthesurfacenish.Becertaintorinseallcleaningagentscompletelyandpolishwithasoftcloth.
Harsh abrasive cleaners are not required and should not be used.
Mild abrasives such as liquid automotive cleaning compound or baking soda paste will remove simple scratches
and stains. Cigarette burns can normally be removed without noticeable effect. Deeper scratches or gouges can
becorrectedwithnegritsandpaper(240gritthen400grit)oragreenScotchbritepad.
To maintain or regain luster and make cleaning easier, periodic applications of automobile wax or like products
willkeepthenishlookinglikenew.

96917C (Rev. D - 02/18)
EDF214WC
Page 4
PART NO.ITEM NO.
PARTS LIST
Drain
Ball - Anti-Rotational
Bubbler Body
Retaining Nut
Button
Cover
OriceAssy
Nipple Assembly
Screen
Regulator
Screw - #10-24 Pinned Torx
Bottom - Cover
Kit - Drain Strainer/Ferrule
Strainer
Fountain - Body
Poly Tubing (Cut To Length)
Hex Nut
T-25 Pinned Torx Bit
LK464
75575C
A55102
10031C
40048C
40089C
40322C
15028C
60291C
61313C
75534C
27658C
45336C
55996C
56051C
56092C
70012C
75520C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
NS
DESCRIPTION
Orice Assy:Mineraldepositsonoricecancausewaterowtospurtor
notregulate.Mineraldepositsmayberemovedfromtheoricewithasmall
roundlenotover1/8"diameterorsmalldiameterwire.
CAUTION: Do not le or cut orice material.
Stream Regulator:Iforiceisfreeofmaterialdeposits,regulateowasin
instructions on page 3 (Step 7). If replacement is necessary, see parts list for
correct regulator part number.
Actuation of Quick Connect Water Fittings: Cooler is provided with lead-
free connectors which utilize an o-ring water seal. To remove tubing from the
tting,relievewaterpressure,pushinonthegraycollarwhilepullingonthe
tubing.(SeeFigure2,Page1).Toinserttubing,pushtubestraightintotting
until it reaches a positive stop, approximately 3/4".
TROUBLE SHOOTING & MAINTENANCE
FIG. 4
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800..834.4816
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com
PRINTED IN U.S.A.
16
15
17
1
11, 12
13
14
2
SEE FIG. 5
6
FIG. 6
9
10
5
4
3
7
8
FIG. 5
17
NS = NOT SHOWN
Cover
Button