Elkay EFRP8C Installation manual

97018C (Rev. C - 9/02)
EFRP8C & EFRPC8C
Installation/Care/Use Manual
EFRP8C & EFRPC8C
Refrigerated Fountains with FLEXI-GUARD®
To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLA-
TION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE
CODES. After installation, leave these instructions inside the fountain for future reference.
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING
THE PROPER MATERIALS AS INDICATED.ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING
PLUMBING SYSTEM.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
13
20
21
19
SEE BUBBLER
ASSY DETAIL
22
SEE SPREADER
DETAIL
36, 37
Installer

97018C (Rev. C - 9/02)
EFRP8C & EFRPC8C
FIG. 1
EFRP8C & EFRPC8C ROUGH-IN
PAGE 2
LEGEND:
A= WATER INLET LOCATION (BOTH SIDES). 3/8" O.D. UNPLATED COPPER TUBE CONNECT.
B= WASTE OUTLET LOCATIONS (BOTH SIDES). 1-1/4" O.D. DRAIN (TRAP NOT FURNISHED)
C= ELECTRICAL SUPPLY LOCATION (BOTH SIDES)
D= MOUNTING HOLES FOR 1/4" DIA. (6mm) SCREWS
E= WASTE OUTLET LOCATION. 1-1/4" O.D. DRAIN (TRAP NOT FURNISHED)

97018C (Rev. C - 9/02)
EFRP8C & EFRPC8C
PAGE 3
FIG. 2
TUBE IS
SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
FIG. 3
OPERATION OF QUICK CONNECT FITTINGS
CUSPIDOR DRAIN FOUNTAIN
DRAIN
14
12
15
19
17
25
BUBBLER ASSY
7
14
4NOTE:
WHEN INSTALLING REPLACEMENT BUBBLER
AND PEDESTAL, TIGHTEN NUT (ITEM 25)
ONLY TO HOLD PARTS SNUG IN POSITION.
DO NOT OVER TIGHTEN.
11
INSTALLATION INSTRUCTIONS
1. Wall should already be framed for the fountain using dimensions shown in Fig. 1.
Shown dimensions pertain to installation location. (Framing shown for reference only).
2. Fasten mounting box or boxes into wall cutout(s) using bolts or screws (not provided).
3. Mount fountain body (and cuspidor when applicable) on mounting box. Screws and clips are
provided for fastening fountain body to box.
4. Remove strainer and the 3/8" O.D. tube that is inserted in it from the refrigeration package.
Install a 1/4 union (2 provided) on both the inlet and outlet line of the refrigeration package by pushing
the tubes straight into fittings until they reach a positive stop, approximately 3/4". (See Fig. 3) DO NOT
SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE O-RINGS MAY RESULT.
5. Place refrigeration package inside mounting box and connect the chiller inlet line with the tube
coming from the regulator holder (See Page 4) and connect the chiller outlet line with line coming from
the bubbler.
6. On cuspidor models, connect 1/4 tube coiled in fountain to spreader. (See Page 4)
7. Water supply is 3/8" O.D. and waste tailpiece(s) are 1-1/4" O.D. Contractor is to supply waste
trap(s) and service stop valve in accordance with local codes.
8. Connecting lines to be unplated copper and thoroughly flushed to remove all foreign matter before
connecting to fountain assembly.
9. Connect the fountain to supply line by installing a union between the supply and fountain.
10. Electrical: Insure power supply is identical in voltage, cycle, and phase to that specified on the
refrigeration package serial plate. Never wire compressor direcly to the power supply.
11. Turn water supply on and check thoroughly for leaks.
12. Release air from tank by depressing push bar; a steady stream of water assures all air is removed.
13. Re-check for leaks.
14. Stream height is factory set at 35 PSI. If supply pressure varies greatly from this, turn adjustment
screw on regulator (item 24). Clockwise adjustment will raise the stream height and counter-clockwise
adjustment will lower stream height. For best adjustment, stream should hit basin approximately 6-1/2"
from the bubbler.
15. Rotate fan blade on refrigeration package to insure proper clearance and free fan action.
16. Connect power supply.
17. Install grill using #8 x 1.00" (25mm) PH screws and small clips provided.
8
NOTE: WATER FLOW
DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY

97018C (Rev. C - 9/02)
EFRP8C & EFRPC8C
PAGE 4
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
ELKAY MANUFACTURING COMPANY  2222 CAMDEN COURT  OAK BROOK, IL 60523  630.574.8484
DESCRIPTION
15005C
21705C
21708C
20397C
22911C
22912C
40575C
45336C
40045C
40206000
40322C
40572C
40624C
50074C
55997C
50198C
56011C
50986C
56073C
55000857
55001086
55001080
61314C
70002C
75580C
70018C
70278C
70378C
55996C
70682C
70920C
70971C
70977C
75555C
70683C
74070030
74070032
MB23A
MB24
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
NS
NS
PART NO.
NUT - RETAINING
CLIP - PUSH ROD
PUSH BAR ASSY
TAILPIPE (FOUNTAIN)
BRKT - LEVER PUSH
BRKT - PUSH BAR MTG
STRAINER/FERRULE ASSY (FTN)
STRAINER/FERRULE ASSY (CUSP)
HEX NUT - UNPLTD
RETAINER
ORIFICE ASSY
TAILPIPE (CUSPIDOR)
HEAD-SPREADER
GASKET - TAILPIPE
PEDESTAL
BUSHING - SNAP
HOUSING ASSY
HOLDER - REGULATOR
BUBBLER ASSY
CUSPIDOR
FOUNTAIN
GRILL EFRP
REGULATOR - W/GREEN SPRING
SCREW-#10 X .50 HHSM
NUT - 3/8-18 LKNT
NUT 1/4-20 HEX
ROD - SUPPORT
ROD - PUSH
STRAINER
TEE - 1/4
ROD - PIVOT
ELBOW 90 DEGREES-TUBE TO
NUT - LOCK 1/2 CONDUIT
CLIP -.125 STUD LOCK
UNION - 1/4
SCREW - #8 x 1.00 PH
SPEED NUT - #8
MOUNTING BOX - FOUNTAIN
MOUNTING BOX - CUSPIDOR
ITEM NO.
PARTS LIST
13
33
32
29
30
10
5
1
23
9
24
34
26
6
18
24
3
27
10
2
28
16
31
CUSPIDOR
SPREADER DETAIL
EFRP8C TUBE ROUTINGS
EFRPC8C TUBE ROUTINGS