Elkay Soft Sides LCRSPD10-2AQ Installation manual

1000002394 (Rev. C - 6/15)PAGE 1
LCRSPD10_2AQ
Installation/Care/Use Manual
Soft Sides®Refrigerated Fountains
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
FIG. 1
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER
LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY
FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREAT-
ING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT
OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY
DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE
THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
IMPORTANT! INSTALLER PLEASE NOTE.
To assure you install this model easily and correctly, PLEASE READ THESE
SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION.
CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING,
ELECTRICAL AND OTHER APPLICABLE CODES. After installation, leave
these instructions inside the fountain for future reference.
Installer
FIG. 2
FIG. 3
14 16
10
12 830 15 22
38
19
29
29
9

1000002394 (Rev. C - 6/15)
LCRSPD10_2AQ
PAGE 2
FIG. 4
3-3/4"
95mm 12-1/8" 309mm 3-3/4" 95mm
19-3/4"
502mm
22"
558mm
22-1/4"
564mm
FINISHED FLOOR
3-7/8"
99mm
27"
686mm
ADULT ADA
REQUIREMENT
31-3/8"
797mm
18"
457mm
13-5/8"
347mm
4-1/2"
114mm WALL OPENING
FINISHED WALL LINE
BACK WALL LINE
14"
354mm
MINMUM DEPTH
28-1/8"
714mm
A
BC
D
LEGEND
A = 1-1/4” (32mm) DRAIN TUBE (PROVIDED)
B = ELECTRICAL INLET
C =3/8" O.D. TUBE CONNECT (CHILLER WATER INLET) SHUT OFF VALVE BY OTHERS
D =3/8” O.D. TUBE CONNECT (CHILLER WATER OUTLET)

1000002394 (Rev. C - 6/15)PAGE 3
LCRSPD10_2AQ
FILTER INSTALLATION INSTRUCTIONS
1. Remove front panel of chiller. Note: For color images please visit www.elkay.com.
2. Install 3/8" formed copper tube (item 4) to left side of lter head. Screw locknut hand-tight to seal. See Figures 5 and 14.
3. Mount lter head to chiller using (3) screws (provided). See Figure 6.
4. Push (1) piece of 3.5" long 1/4" O.D. poly tubing (item 27, provided) into tting on right side of lter head. See Figure 7.
See Figure 1 for operation of quick connect ttings.
5. Install 1/4" x 1/4" John Guest elbow (provided) to previously installed poly tubing. Install 3/8" x 1/4" John Guest elbow
(provided) to evaporator water inlet labeled "WATER IN". See Figure 8.
6. Connect 1/4" John Guest elbow to 3/8" x 1/4" John Guest elbow using (1) piece of 3.5" long 1/4" O.D. poly tubing (item
27, provided). Install lter cartridge to lter head. See Figure 9.
FIG. 5
FIG. 6 FIG. 7
FIG. 8 FIG. 9
27
27
37
33
4
3
34
11
24

1000002394 (Rev. C - 6/15)
LCRSPD10_2AQ
PAGE 4
INSTALLATION INSTRUCTIONS
1. Install mounting frame. See rough-in diagram (Figure 4) and mounting frame installation instructions.
2. Install remote chiller. Verify that lter has been installed inside chiller. Slide chiller onto shelf and center it within the shelf
guides. NOTE: Building construction must allow for adequate air ow on both sides, top, and back of chiller. See chiller
instructions for additional information.
3. Make water supply connections. Install a shut-off valve and union connection to building water supply (valve and union
not provided).
4. Make connection between chiller inlet and building supply line (3/8" O.D. copper tube). DO NOT SOLDER TUBES
INSERTED INTO THE UNIONS AS DAMAGE TO THE O-RINGS MAY RESULT. (See Figure 10).
5. Hang the upper panel on the mounting frame hanger. Align holes in the panel with the holes in the mounting frame. Be
sure that panel is engaged with hanger at top of frame before releasing it.
6. Install the fountain. Remove access cover plate on underside of fountains and save the screws. Mount the fountain to
the upper panel and the wall frame with (4) 5/16" x 3/4" (19mm) long bolts and nuts (provided). Tighten securely.
7. Insert waste tube (provided) into drain on fountain. Attach waste tube (1-1/4" O.D.) to 1-1/4" O.D. slip trap (provided by
others).
8. Make connections between remote chiller and fountain. Outlet port is marked on the chiller (3/8" O.D. copper tube).
Install a 3/8" x 1/4" union (provided) on the marked chiller outlet port. Insert the 1/4" poly tubing coming from the fountain
into the union. Turn on water supply, ush line thoroughly, and check for leaks. DO NOT SOLDER TUBES INSERTED
INTO THE UNIONS AS DAMAGE TO THE O-RINGS MAY RESULT. (See Figure 10).
9. These products are designed to operate on 20-105 PSIG (0.14-0.72 MPa) supply line pressure. If inlet pressure is
above 105 PSIG (0.72 MPa), a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting these products to supply line pressures lower than 20 PSIG (0.14 MPa) or higher than 105 PSIG (0.72 MPa)
is not covered by warranty.
10. Make electrical connections to the chiller. See chiller instructions.
11. Check stream height from bubbler. Stream height is factory set at 35 PSI. If supply pressure varies greatly from this,
adjust the screw on regulator item 10 by using a small screwdriver through the small hole in the push button item 3
(See Figure 3). Clockwise adjustment will raise stream height and counter-clockwise will lower stream height. For best
adjustment stream should hit basin approximately 6-1/2" from the bubbler.
12. Mount lower panel. Slide upper tounge of lower panel under lower edge of already installed upper panel. Tighten
previously loosened screws securely. Install (2) #10-24 x 5/8" (16mm) screws at frame bottom lip.
13. Replace bottom access panel to fountain basin using screws provided. Tighten securely.
TROUBLE SHOOTING AND MAINTENANCE
1. Orice Assy: Mineral deposits on orice can cause water ow to spurt or not regulate. Mineral deposits may be removed
from orice with a small round le not over 1/8" diameter or a small diameter wire.
CAUTION: Do not le or cut orice materials.
2. Stream Regulator: If orice is free of material deposits, regulate ow according to instruction 11 stated above.
3. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an o-ring water
seal. To remove tubing from the tting, relieve water pressure, push in on the gray collar while pulling on the tubing (See Fig. 1)
To insert tubing, push tube straight into the tting until it reaches a positive stop, approximately 3/4".
TO BUBBLER
CHILLER OUTLET
TUBE ROUTING DIAGRAM
FIG. 10
CHILLER INLET
REGULATOR ASSEMBLY (SEE FIG. 2)
27
27
31

1000002394 (Rev. C - 6/15)PAGE 5
LCRSPD10_2AQ
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
SEE FIG. 3
SEE FIG. 2
PARTS LIST
ITEM
NO.
PART NO. DESCRIPTION
1 1000002264 PANEL - UPPER
2 1000002265 PANEL - LOWER
31000002267 BRKT-LK FILTER
4 1000002409 TUBE -CU 3/8" WATER INLET
5111577243890 SCREW-MACH 5/16-18X3/4
6111577343890 NUT-SERRATED HEX 5/16-18
7 75570C SCREW - #10 X .50 PINNED TORX
8 15005C NUT - REG RETAIN 1 1/8 - 24
9 15009C NIPPLE-BUBBLER (GF)
10 28824C BRKT - REGULATOR MTG.
11 38417001 SCREW -#8-18X.37 HHSM
12 40045C NUT - HEX 1 15/16UN-2B UNPLATED
13 45768C PLUG-DRAIN 1-1/2 (SWIRLFLO)
14 45662C BUTTN - PUSH
15 45736C NUT -REG. MNTG. HALF
16 45737C SLEEVE-PUSH BUTTON GUIDE
17 45769C ASSY-DRAIN/TAILPIPE SWIRLFLO
18 45805C ADAPTER - DRAIN
19 45866C BODY-BUBBLER (SHORT)
20 56163C GASKT - DRAIN
21 50090C INSUL-ARMAFLEX
22 50986C HOLDR-REGULATOR
23 51294C ASSY-FILTER HEAD
24 51299C ASSY -FILTER (LK-LEAD)
25 28630C COVER-BOTTOM FTN
26 55001162 RD FRNT 18" FNT ARM ASSY CHILD ADA
27 56092C TUBE-POLY 1/4 X .040 WALL
28 56280C EDGE TRIM 5/16" CHROME
29 56305C GASKT - VR BUBBLER
30 61313C REG -W/ SPRING
31 70745C FTTNG-UNION 3/8 X 1/4 TUBE
32 70792C SCREW -#8-18 X .75 SS PHHL
33 70793C FTTNG-ELBOW 1/4 X 90
34 70817C FTTNG-ELBOW 1/4 STEM X 1/4 90
35 70822C FTTNG-SUPERSEAL 1/4
36 70823C FTTNG-SUPERSEAL 3/8
37 70836C FTTNG-ELBOW 3/8 X 1/4 90
38 75672C SCREW-CAP #6-32
39 MFC100Q MOUNTING FRAME ADA-QATAR
39
27
27 26
1
5, 6
5, 6
31
2
13, 17, 20
25
7
28
332
36 35 34
24
FIG. 11
FIG. 12
FIG. 13
Note: Screw the locknut hand tight to seal
FIG. 14
23