Elkay FLEXI-GUARD EFW16 1E Series Installation manual

PAGE 1 97351C (Rev. B - 9/00)
EFW16*1E,2E
With FLEXI-GUARD®
Installation/Care/Use Manual
USES HFC-134A REFRIGERANT
FIG. 1
SEE FIG.5
SEE FIG.4 7 26, 27
16, 17, 18, 19
28
21, 22
29
20
35
23
31
33
25, 30
15
36
24
32
13
34
14
40
39
38
41

PAGE 2
97351C (Rev. B - 9/00)
EFW16*1E,2E
FIG. 2
FINISHED FLOOR PISO ACABADO PLANCHER FINI
E = INSURE PROPER VENTILATION BY MAINTAINING 4" (102mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGURE UNAVENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 4" (102mm) (MÍN.) DE HOLGURA ENTRE LA REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 4" (102mm) (MIN.) ENTRE LES ÉVENTS DE LENCEINTE ET LE MUR.
F = POWER CORD 4 FEET (1219mm) LONG
CABLE ELÉCTRICO DE 4 PIE (1219mm), DE LARGO CORDON DALIMENTATION 4' (1219mm)
G = PLUMBING ROUGH-IN CAN BE LOCATED ANYWHERE WITHIN THIS AREA.
SE PUEDE COLOCAR EL DESBASTE DE LATUBERÍA EN CUALQUIER LUGAR DENTRO DE ESTA ÁREA. ON PEUT PLACER LATUYAUTERIE DANS CETTE RÉGION.
LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38mm) OUT
FROM WALL SHUT OFF BY OTHERS
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT.A 1-1/2"
(38mm) FUERA DE LA LLAVE DE PASO EN LA PARED COLOCADA POR TERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E.
CONNECTANT UNE TUYAUTERIE DE 1-1/2 PO. (38mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4 O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1¼ DE DIÁMETRO. EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE DEAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADOR DE 1¼ NO PROPORCIONADO** SIPHON 1-1/4 NON FOURNI**
D = ELECTRICAL OUTLET LOCATION
UBICACIÓN DE LA TOMA DE ELECTRICIDAD EMPLACEMENT DE LA PRISE DE COURANT

PAGE 3 97351C (Rev. B - 9/00)
EFW16*1E,2E
FIG. 3
Stream height is factory set at 35 PSI. If supply pressure varies
greatly from this, remove items 1 & 2 and adjust screw on
item 4. Clockwise adjustment will raise stream and counter-clockwise
adjustment will lower stream. For best adjustment, stream should hit
basin approximately 6-1/2" (165mm) from bubbler.
BASIN
FIG. 4
NOTE:
WHEN INSTALLING REPLACEMENT
BUBBLER AND PEDESTAL,
TIGHTEN NUT (ITEM 12) ONLY TO
HOLD PARTS SNUG IN POSITION.
DO NOT OVER TIGHTEN.
FIG. 5
BASIN
9
10
11
12
8
CONDENSER WATER VALVE ADJUSTMENT
The condenser water valve is factory preset for a condenser water outlet temperature of 95° to 105° F.
If actual temperature varies greatly from this, readjust water flow rate at the valve using the following procedures.
1. START UP COMPRESSOR
This can be accomplished by depressing the cooler push button (See Fig. 4 - Item 2). Keep water running
during the entire readjustment procedure.
2. ADJUSTMENT CONDENSER WATER VALVE
Adjust valve by rotating adjustment stem. Rotating stem clockwise will decrease water flow. Counterclockwise
rotation will increase water flow. Increasing water flow will result in a lower condenser outlet temperature, while
decreasing water flow will result in a higher outlet temperature. Proper adjustment is attained when condenser
outlet temperature is 95° to 105° F.
4
3
1
5
6
2
WIRING DIAGRAM
This Drawing is merely for illustrating the
components of the electrical system.

PAGE 4
97351C (Rev. B - 9/00)
EFW16*1E,2E
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
ELKAY MANUFACTURING COMPANY  2222 CAMDEN COURT  OAK BROOK, IL 60523  630.574.8484
PRINTED IN U.S.A.
PARTS LIST 115V
PART NO. DESCRIPTION
40089C
40048C
15005C
61313C
40169C
50986C
20776C
51349C
40322C
50934C
50168C
70012C
31513C
30268C
45395C
35762C
31027C
31797C
194243901550
55996C
45690C
55909C
66229C
66506C
40136C
50368C
70750C
75568C
70682C
70233C
55981C
51454C
66202C
75494C
SEE TABLE
SEE TABLE
SEE TABLE
20708C
22540C
22547C
27961C
56092C
Cover
Button
Regulator Retaining Nut
Regulator
Hex Nut
Regulator Holder
Basin
Bubbler Assy
Orifice Assy
Housing Assy
Pedestal
Bubbler Locknut
Cold Control
Power Cord
Condenser Assy
Compressor Serv. Pak
Overload/Relay Assy
Relay Cover
Electrical Shield
Strainer
Precooler
Tailpipe Helix
Heat Exchanger
Evaporator
Water Temperature Valve
Receptor - Drain
Clamp - Hose
Screw - Evaporator Mtg
Tee - 1/4
Elbow - 1/4 x 3/8
Snap Bushing
Snap Bushing
Drier
Check Valve 3/8
Panel - Left
Panel - Right
Panel - Front (not shown)
Brace - Cross
Shelf
Baseplate
Bracket - Strain Relief
Tubing Poly (Cut to Length)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16*
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
NS
31440C
35764C
31028C
35768C
14
16*
17
18
Power Cord
Compressor Serv. Pak
Overload/Relay Assy
Relay Cover 220V
PART NO. DESCRIPTIONITEM NO.
220/240v 50Hz
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY,
REPLACE WITH SAME COMPRESSOR USED IN ORIGINALAS-
SEMBLY.
NOTE: All correspondence pertaining to any of the above
water coolers or orders for repair parts MUST include Model
No. and Serial No. of cooler, name and part number of re-
placement part.
Item No. 35
Part No.
COLOR TABLE
Gray Beige
Almond
Stainless Steel
Sandalwood
Granite
Light Gray Granite
20622C
21460C
20624C
21458C
27165C
27166C
27653C
27655C
27652C
27656C
27654C
27657C
20657C
20658C
20654C
21450C
27147C
27148C
PANEL
COLOR
Item No. 36
Part No. (w/o hole)
Item No. 37
Part No.
ITEM NO.
20623C
24161C
20625C
21459C
27168C
N/A
Item No. 36
Part No. (w/ hole)