Elkay LK4595 FTN Series User manual

Page 1 97460C (Rev. SIC - 1/11)
4595_FTN LK4595_FTN
Owners Manual
Model 4595
Pedestal Barrier Free Stone Fountain
Toassureyouinstallyour4595StoneFountainmodeleasilyandcorrectly,
PLEASEREADTHESESIMPLEINSTRUCTIONSBEFORESTARTINGTHE
INSTALLATION.CHECKYOURINSTALLATIONFORCOMPLIANCEWITH
PLUMBING,ELECTRICAL,ANDOTHERAPPLICABLECODES.Afterinstallation,
leavetheseinstructionswiththeFountainforfuturereference.
IMPORTANT
ALLSERVICETOBEPERFORMEDBYANAUTHORIZEDSERVICEPERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THEGROUNDINGOFELECTRICALEQUIPMENTSUCHASTELEPHONE,COMPUTERS, ETC.TOWATERLINES
ISACOMMONPROCEDURE.THISGROUNDING MAYBEINTHEBUILDING OR MAYOCCURAWAYFROMTHE
BUILDING.THISGROUNDINGCANCAUSEELECTRICALFEEDBACKINTOAFOUNTAIN,CREATINGAN
ELECTROLYSISWHICH CAUSESAMETALLICTASTEORAN INCREASEINTHE METALCONTENTOFTHE
WATER.THISCONDITIONISAVOIDABLE BYUSINGTHE PROPER MATERIALSAS INDICATED.ANYDRAIN
FITTINGSPROVIDEDBYTHEINSTALLER SHOULD BE MADE OF PLASTICTOELECTRICALLYISOLATETHE
FOUNTAIN FROMTHE BUILDINGPLUMBINGSYSTEM.
INSTALLER
General Installation Tips
1. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/4" IPS. Contractor to supply waste trap and service stop valve
in accordance with local code.
2.Connectinglines to bemade of unplated copperand should be thoroughlyflushed to remove allforeign matter before
being connected to fountain. This fountain is manufactured in such a manner that it does not in any way cause taste,
odor, color, or sediment problems.
3.Connect fountain to supplyline with ashut-offvalve and installa 3/8" unplated copperwater line betweenthe valve and
the cooler. Remove any burrs from outside of water line. Push the tubes straight into the fittings until they reach a
positivestop, approximately3/4" (SeeFig. 6).DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS
DAMAGE TO THE O-RINGS MAY RESULT.
4. These products are designed to operate on 20 psig to 105 psig supply line pressure. If inlet pressure is above 105 psig,
a pressure regulator must be installed in the supply line.Any damage caused by reason of connecting this product to
supply line pressures lower than 20 psig or higher than 105 psig is not covered by warranty.

Page 297460C (Rev. SIC - 1/11)
4595_FTN LK4595_FTN
Installation Instructions
1.This fountain is to be mounted on a smooth, flat, finished surface with adequate support structure. NOTE: Mounting
structure must be capable of supporting 300 lb. load on fountain.
2.Refertorough-infor plumbing.
3.Installshut-offvalveonwater supply.(Valvenotfurnished).
4.Locate andinstall fountain using 3/8" minimum screws or bolts. (Screws or bolts not furnished). CAUTION: This fountain
is rated for inlet water pressure of 20-105 PSI. Apressure reducing regulator should be used if the inlet water supply
exceeds 105 PSI.
5. Connect water supply and fountain drain. Water connection and drain must comply with local codes.
6. Turn on water supply and check all connections for leaks.
FIG. 1

Page 3 97460C (Rev. SIC - 1/11)
4595_FTN LK4595_FTN
17
6
18
2
24
See Fig. 3
9-A
STREAM HEIGHTADJUSTMENT: Stream heightis factory setat
35 PSI. If supply pressure varies greatly from this, remove
items 7 and 8 (See Fig. 3) and adjust screw on item 19.
Clockwise adjustment will raise stream and counter-clockwise
adjustment will lower stream. For best adjustment, stream
should hit basin approx. 6-1/2" from bubbler.
FIG. 2
FIG. 3 FIG. 4
84
19 13
10
7
11
22 16
16
16
15
12
1
2023
3
1
14
24
23
22
5
2
29-B
6
3
2
5
16
18
21
16
BUBBLERDETAIL

Page 497460C (Rev. SIC - 1/11)
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
PRINTEDINU.S.A.
DESCRIPTION
100147140560
100322740560
101570540560
15005C
15013C
170705042830
40048C
40089C
400942308640
98287C
40169C
40250C
45476C
50986C
55913C
55996C
56092C
56121C
600985551640
61313C
66346C
70682C
70683C
75588C
75589C
1
2
3
4
5
6
7
8
9 - A
9 - B
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
PARTNO.
Drain Gasket
Bubbler Gasket
Drain Gasket
Regulator Retaining Nut
Bubbler Tube Assy.
Basin
Button
Cover Nut
Bubbler
Bubbler Assembly
Hex Nut 1-5/16-20UN
Tailpipe 1-1/4" x 5-3/8"
Drain Tube
Regulator Holder
Drain Adapter
In-Line Strainer
Poly Tubing (Cut To Length)
Drain Elbow 1-1/4"
Drain Plug Assy.
Regulator
Drain Tube
Tee - 1/4
Union - 1/4
Slip Joint Nut 1-1/4"
Gasket
ITEMNO.
PARTSLIST
FIG. 6
NOTE:WATER FLOW
DIRECTION
BUILDINGWATER INLET
SERVICESTOP
(NOT FURNISHED)
1/4"O.D.TUBE
WATER INLET
TO FOUNTAIN
3/8"O.D.UNPLATED
COPPERTUBECONNECT
COLDWATERSUPPLY
TROUBLESHOOTING ANDMAINTENANCE
Orifice Assy: Mineral deposits on orifice can cause water
flow to spurt or not regulate. Mineral deposits may be
removedfrom the orificewith a smallround file orsmall
diameter wire. CAUTION: DO NOT file or cut orifice
material.
Stream Regulator: If orifice is clean, regulate flow as in
"STREAMHEIGHTADJUSTMENT"instructions on page
3. If replacement is necessary, see parts list for correct
regulatorpartnumber.
Actuation of Quick Connect Water Fittings: Fountain is
providedwithlead-freeconnectorswhich utilize an o-ring
waterseal. Toremovetubing from the fitting,relieve water
pressure, push in on the gray collar while pulling on the
tubing (See Fig. 5). To insert tubing, push tube straight
into fitting until it reaches a positive stop, approximately
3/4".
FIG. 5
4595_FTN LK4595_FTN