ELRO LP152011 User manual

1
LP152011/LP152012
MOTION SENSOR
Your security motion sensor is a fully automatic indoor
and outdoor security/courtesy light controller capable
of controlling up to 1000W incandescent, 400W
fluorescent or 150 Watt. Time and LUX adjustment
functions let you select how long and when the light
will stay on after activation.
Note: Read this entire manual before you start to
install the system.
Wall mounting, 1.8~2.0m above the ground.
Ceiling mounting, 2.5~4.0m above the ground ed.
Outdoor installation; under eaves is preferable.
Do not allow sunlight to fall directly on the front of
unit, and try to avoid pointing the unit at trees or
shrubs or where the motion of pets may be
detected.
SENSOR SENSOR
LESS SENSITIVE MORE SENSITIVE
200 degree
Install a wall switch adjacent to the power source. This
helps you operate AUTOMATIC OPERATION and
MANUAL OVERRIDE with ease.
Make use of the base cover as a template to mark the
position of two screw holes on the wall or on the
ceiling.
Strip approximately 6-8mm insulating part of the wires
from the power cord. Before connection, run the wires
through the rubber seal provided.
For wire connection:
SAFETY INSTRUCTIONS
Do not attempt installation unless you have some
experience with household wiring.
Before proceeding with the installation;
TURN
OFF THE POWER TO THE LIGHTING
CIRCUIT
AT THE CIRCUIT BREAKER OR FUSE
BOX TO AVOID ELECTRICAL SHOCK
DO ensure that the power supply circuit is protected
by a 16 amp circuit breaker or suitable equivalent
fuse..
DO NOT install this motion sensor when it is raining.

2
(1) TEST MODE
Turn the LUX control and the TIME control
counter clockwise to the edge – the TEST
position.
Turn on the wall switch. The light starts warm-up
for 1 minute. During 1 minute warm-up period, the
light will stay on.
Walk through the detection area. The light turns
on when you move and turns off when you stop.
For a smaller coverage area, point the sensor
down; for a larger coverage area, point the sensor
up.
(2) TIME ADJUSTMENT
The TIME adjustment controls how long the light will
stay on after the motion has been detected.
About
5 seconds About 12 minutes
(3) LUX ADJUSTMENT
The LUX adjustment determines at what light level the
lighting system will start operating when you set the
sensor to automatic operation.
(4) AUTOMATIC OPERATION
Turn on the wall switch. When the sensor detects
motion, the light automatically turns on. The built-in
photocell turns the sensor off and on according to the
light level selected by the LUX adjustment.
(5)MANUAL OVERRIDE CLICK TWICE
Automatic switching can be overridden to allow the
lighting to illuminate regardless of movement or light
sensitivity. Turn the switch OFF - ON - OFF - ON
within 2 seconds.
In manual override mode, the lighting will remain on
for approx. 4 to 6 hours regardless of movement. Then
the motion switch will return to automatic mode.
You can also manually set the motion switch to
automatic mode by turning it off for 10 seconds, and
then on again.
TROUBLESHOOTING
Light does not turn on:

Confirm that you have made a correct “wiring
connection”.
Check if you have already turn
ed on the
connected wall switch, or circuit breaker.

Examine if the bulb of the lighting system is in
good condition or loose.
Adjust the LUX
control knob by turning it counter
clockwise.
Light remains on:
Make sure the wiring connection is correct.
SPECIFICATIONS
Power Requirement
AC 220 ~ 240V / 50Hz
Lighting Load
Up to 1000W Halogen/
Incandescent
Up to 400W Fluorescent
Up to 150W LED
Detection Field
(at 20°C)
Up to 200° and 12 meter
Swiveling Angle
Vertical 35° Horizontal 70°
Mounting Height
1.8 ~ 2.0m Wall Mount
or 2.5 ~ 4.0m Ceiling Mount
Sensor Operation
Auto/Manual Override
Time Adjustment
Approx. 5 sec ~ 12 min
Lux Adjustment
Approx. 30 ~ 200 Lux
Warm Up Time
About 1 min.
Protection Class
II
Protection Degree
IP44
Safety
CE