ELTA FANS ZOO FAN SDF Maintenance and service guide

These instructions must be read fully before commencing installation.
ZOO FAN SDF
Installation & Maintenance

Tel [phone] Fax [phone] Email [email protected] Website eltafans.com2
Installation Instructions
ZOO FAN SDF ECAC
1.0 General
1.1 It is important these Installation and Maintenance Instructions are fully adhered to.
1.2 Full details of the unit supplied are shown on the product nameplate. If in doubt about any detail contact Elta Fans Ltd or its agents for
clarification.
1.3 All electrical installation must be carried out by suitably qualified and competent personnel in accordance with all current statutory
requirements.
1.4 These instructions cover only the Elta Fans Ltd product and do not include the supply or installation of any safety equipment that may be
required e.g. adequate guarding or protection from rotating parts and proper electrical isolation.
1.5 Any declarations made by Elta Fans Ltd about product installation and safety, are dependant on the fan equipment being used within
installations which themselves meet the requirements of the relevant Standards and Directives of your region.
1.6 The fan is designed for use in an ambient temperature of -20°C up to a maximum of +70°C (refer to the relevant table) and up to 95%
relative humidity. The fan is not suitable for corrosive or explosive atmospheres.
1.7 The installer should provide easy access to the fan to facilitate future maintenance.
1.8 The installer should ensure the fan is adequately supported.
1.9 This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person
responsible for their safety. Children should be supervised to ensure that they do not play with the product.
1.10 At end-of-life, the unit must be disposed of in an environmentally friendly manner by suitably qualified and competent personnel in
accordance with the requirements of applicable Standards and Directive
2.0 Installation
WARNING – Rotating equipment. Death, severe injury and property damage may result. ZOO Fans are intended to be hung out-of reach
of people. The bottom of the fan must be no less than 3.05m from any area capable of receiving pedestrian traffic. The fan must be
isolated from the power supply during installation and maintenance. The fan must be earthed in accordance with the local regulations.
2.1 Upon receipt, the fan equipment should be visually inspected to check for any damage. Ensure that the impeller is free to rotate.
2.2 If there are any queries concerning the fan equipment, Elta Fans Ltd should be contacted prior to the installation.
2.3 The fan must be securely mounted in the desired position to suit the application. (Refer to Gripple Fastening Method).
2.4 Check the details on the motor rating plate to ensure that the correct power supply (voltage, frequency and phase) is available. An
incorrect power supply will lead to permanent damage to the fan motor.
2.5 Refer to the appropriate wiring diagram. Ensure that all earth connections are made.
2.6 Means for electrical disconnection must be incorporated in the wiring installation in accordance with the relevant wiring and electrical
regulations.
2.7 Precaution must be taken to locate the exhaust discharge terminal so as to avoid the backflow of gases into the room from the open flue
of gas or other fuel burning appliances.
3.0 Gripple Fastening Method
3.1 Using the 3m Cable with M8 Stud End Fixing, attach the Gripple to the handle of the fan.
NOTE – Gripple Installation Guidelines are included with your Gripple hardware and should be consulted for guidelines on how to install,
adjust, and care for your Gripple attachment hardware.
3.1.1 Screw regular M8 Nut to the top of the M8 Stud Fixing
3.1.2 Place M8 Flat Washer on the thread
3.1.3 Insert M8 Stud Fixing (with installed nut and flat washer) through the center hole in the handle
3.1.4 Place M8 Flat Washer and M8 Nylock Nut on thread sticking through the handle
3.1.5 Securely tighten M8 Nylock Nut
3.2 Fasten Stabalisation Tether Gripple
Using the 4m Cable with Eyelet Fixing, attach the Gripple to the handle of the fan.


Elta Fans Limited has a policy of continuous product development and improvement and therefore reserves the right to supply products which may differ from those illustrated and described in this publication.
Confirmation of dimensions and data will be supplied on request. 3
TIP – Leave the Gripple wire wound in a circle, as it is shipped, until you are ready to install the Stabilization Tether to the Truss, I-Beam,
or support structure
3.2.1 Insert proper M6 Hex Head bolt through the Eyelet of Gripple:
3.2.2 Use M6 x 50 Hex Head bolt for SDF250
3.2.3 Use M6 x 60 Hex Head bolt for SDF300
3.2.4 Insert M6 Hex Head bolt through the hole located at 45° on either side of the handle
3.2.5 Securely tighten M6 Nylock Nut
To secure the Main Hanging Gripple and Stabilization Tether to the Truss, I-Beam, or support beam.
WARNING – The Stabilization Tether MUST be installed properly to ensure safe operation of your ZOO Fan.
3.2.4 Place Gripple on the wire
3.2.5 Loop wire over Truss, I-beam, or support beam (Tether at a 45 ° angle)
3.2.6 Push end of wire into Gripple
3.2.7 Adjust wire so there is no slack
4.0 Start Up
4.1 Before power is supplied to the unit, check that the wiring is correct as per the fan connection diagram.
4.2 At initial start-up, check that impeller rotation and airflow direction is correct.
4.3 Check that the motor amperage draw does not exceed the nameplate rating.
5.0 Fan Maintenance
5.1 Inspection of the fan at least once every 12 months is recommended to ensure that the motor, fan blades, and supporting guards, are
clean. Any build up of dust and deposits on the blades or guards should be removed using a non-abrasive cleaner.
5.2 All fastenings should be checked for tightness. In addition, all rotating items should be checked.
5.3 Bearings are of the ‘sealed for life’ type and will not need a detailed inspection.
WARNING – This fan is fitted with an auto-reset thermal contact which switches the fan off in the event of a fault condition.
Once the motor cools down the fan may start unexpectedly.
Only a suitably qualified and competent person may carry out maintenance after the electrical supply has been isolated.
6.0 Guarantee
Elta Fans Ltd will, free of charge, within a period of 1 year from the date of dispatch from their works, repair or at its option replace
any goods which are proved to have defects as a result of defective materials or workmanship. The goods MUST be returned to Elta
Fans Ltd carriage paid for examination.
Installation Instructions
ZOO FAN SDF ECAC



Tel [phone] Fax [phone] Email [email protected] Website eltafans.com4
Wiring Diagrams
ZOO FAN SDF
Please use the table(s) below to match up the product code and the wiring diagram number.
AC EC
Single Phase 220V to 240V / 50Hz or 60Hz Single Phase 200V to 277V / 50Hz or 60Hz
Page
No.
Product
Code
Wiring
Diagram No.
5SDF250/4-1AC 152-177
5SDF300/4-1AC 152-177
Page
No.
Product
Code
Wiring
Diagram No.
6SDF250/4-1EC 152-00036
6SDF300/4-1EC 152-00036

Elta Fans Limited has a policy of continuous product development and improvement and therefore reserves the right to supply products which may differ from those illustrated and described in this publication.
Confirmation of dimensions and data will be supplied on request. 5
Wiring Diagrams
152-177 AC
TO MOTOR
CONTROLLER TERMINAL BOX
220-240V 1PH 50Hz
SUPPLY
EL N
NLENL AUX
N/
U2
L/
U1
N/
U2
L/
U1
FAN ONLY
TO MOTOR
230V 1PH 50Hz SUPPLY
L N PE
FAN C/W TRANSFORMER SPEED CONTROL (149-TC1_)
FAN
ALL WIRING AND CONTROL EQUIPMENT MUST COMPLY TO THE
LATEST IEE REGULATIONS, IN PARTICULAR PART 552-01-02/03
GREEN/YELLOW
BLUE OR GREY
BLACK
BROWN
GREEN/YELLOW
BLUE OR GREY
BLACK
BROWN
BROWN
BLUE
C
MK-152-177 Issue: C Saved Date: 03/11/17
All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03.
MK-152-177 Issue C: 03.11.2017
Check the individual product accessories table for fan controller compatibility.

Tel [phone] Fax [phone] Email [email protected] Website eltafans.com6
Wiring Diagrams
152-00036 EC
BLUE
RED
WHITE
YELLOW
BROWN
BLUE
GREEN/YELLOW
TO MOTOR
200-277V 1PH 50/60Hz
SUPPLY
FAN ONLY
FAN
NL E1 A1 GND 10V
L N
FAN C/W POTENTIOMETER SPEED CONTROL (149-POT-10)
NL E1 A1 GND 10V
1 2 7 6 5
L N
RED
BLUE
WHITE
YELLOW
BROWN
BLUE
GREEN/YELLOW
149-POT-10
TO MOTOR
200-277V 1PH 50/60Hz
SUPPLY
FAN
ALL WIRING AND CONTROL EQUIPMENT MUST COMPLY TO THE
LATEST IEE REGULATIONS, IN PARTICULAR PART 552-01-02/03
11/07/2013
MK-152-00036 Issue: Saved Date:C
All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03.
MK-152-00036 Issue C: 11.07.2013
Check the individual product accessories table for fan controller compatibility.

Elta Fans Limited has a policy of continuous product development and improvement and therefore reserves the right to supply products which may differ from those illustrated and described in this publication.
Confirmation of dimensions and data will be supplied on request. 7
EC Declaration of Conformity EC Declaration of Incorporation
Description of Equipment:
Building Services Ranges - Air movement fan
Equipment model numbers for safe area fans:
SCP, SPA, SAX, SCD, SDA, SCC, SLC, SCPP, SPP, SAMF, HIT, SEM,
SEL, ISEO IMF, SH, SSD, SQS, SQSDCV, SQU, SMB, STD, SQT, SQT-
DCV, SCH, SCHT, SSDR, SSDRDCV, STDR, STDRDCV, SB, SQU-HT,
SSQU-HT, SDF, ZFHIC, SRC, CF, TF
Relevant / applied directives:
Machinery directive 2006/42/EC, Low voltage directive 2014/35/EU
Relevant / applied directives where applicable:
Energy related products directive 2009/125/EC (when used in Europe)
Electromagnetic compatibility directive 2014/30/EU (where driven via
Inverter)
Relevant / applied directives where applicable:
BS EN ISO 12100 : 2010
BS EN 14694 : 2003 + A1 : 2011
BS EN 308:1997
BS EN ISO 5801:2008
In accordance with the Machinery Directive 2006/42/EC;
The design of the partly completed machine, listed above, complies
with the Essential Health and Safety Requirements (EHSRs) of ANNEX
I, sections 1.1.2, 1.1.5, 1.4.1, 1.5.1 in EC Machinery Directive 2006/42/
EC.
Machinery is incomplete and must not be put into service until such
time as the machinery which is partly complete, is to be incorporated,
and has been assessed and Declared in Conformity with the provi-
sions of any relevant parts of the Machinery Directive.
We undertake to transmit, upon reasoned request by appropriate na-
tional authorities, relevant information relating to the partly completed
machinery identified above.
Manufacturer:
Elta Fans Limited
46 Third Avenue
Pensnett Trading Estate
Kingswinford
West Midlands
DY6 7US
United Kingdom
Date / Signature of Manufacturer: Document last revised: 28th March 2017
Name / Position of Signatory: Mr. Robert Rees Q.A.Manager Elta Fans Ltd
This is an electronic document and is valid without a signature or date. Issue Status B
Herewith we declare that the air movement equipment below, on the basis of its design and construction as partly completed
machines brought onto the market complies with relevant health and safety requirements of the EC Directives stated below. In the
event that alterations are made to the machinery without prior consent from Elta Fans Ltd, this declaration becomes invalid.
EC Declaration of
conformity/incorporation

535-IOM0074 Issue A
eltafans.com
Tel [phone]
Fax [phone]
Email [email protected].uk
46 Third Avenue, Pensnett Trading Estate, Kingswinford,
West Midlands, DY6 7US United Kingdom
Tel [phone]
Fax [phone]
Email [email protected] /[e-mail]
17 Barnes Wallis Road, Segensworth East Industrial Estate,
Fareham, Hampshire, PO15 5ST United Kingdom
BS EN ISO 9001:2015 FM 556465
A member of
HEVAC ASSOCIATION
Applied Technology &
Building Services Export
Building Services