5
For each of the 4 outputs, the following operating modes can be programmed: - Timed operation : On each reading of the key,
the output is activated for the time set in the memory (from 1 to 2550 sec). When this time interval elapses, the output is auto-
matically deactivated.
- ON/OFF operating mode: on the first reading, the relative output is activated, and on the subsequent reading is deactivated
(however the maximum time interval set in the memory remains valid).
For the first 3 outputs it is also possible to simultaneously activate output 4 (according to the relative set time interval). This may
be useful, for example, to open the door for 1 second and simultaneously turn on a common light for 2 minutes.
Combined functions between “probes” 1 and 2 or between 3 and 4 may also be enabled. For example, “probe” 1 may activate
an output and probe 2 could deactivate it.
For each of the 4 inputs, a simultaneous command can be enabled (on the “digital” line) (programmable) to enable the activa-
tion of a remote command (of example via a digital relay 170D activation of a lock not controllable by the control unit).
At the same time as activation of each output the display shows information messages (accompanied by acoustic signals) indi-
cating the type of operation, recognition of the key and the position of the key in the list.
TOUCH KEY MANAGEMENT:
The control unit manages (as standard) 500 “TOUCH” keys. A priority level is also memorised for each key, and the relative per-
missive for the 4 different outputs (i.e. keys may be set to open only specific locks of the 4 available). In programming mode, the
user can scroll through the keys on display, with direct access to each one of the 500 keys, display of the associated parame-
ters, modifications, deletion and entry of individual keys. Complete deletion of all keys is also possible. These operations can be
performed either via the keypad (operations protected by “R4” + password , and for further safety also an optional microswitch
mounted inside the board) or via the special PC software.
CONFIGURATION AS ACCESS CONTROL:
Each control unit is programmable with a special code (“Digibus number” parameter) and controllable “on the network” by means
of a specific 2+1 wire BUS . In this way, one or more remote units (normally PCs)can be used to record all openings, modify per-
missive of single control units or individual users, modify priority levels, and update/download/upload utilities.
KEY PROGRAMMING AND OPERATION VIA THE KEYPAD:
The control unit enables, in addition to the use of touch-keys, management of an access point via the KEYPAD. This can memo-
rise 100 different 8-digit codes usable to activate relay output n°1. Operation and programming of these codes is the same as in
the case of the digital panel (digibus). The key action modes are the same as those of touch1. In practice opening is activated
on output 1 with the relative time intervals and functions.
NB: For special application, the 2 effects of keypad keys and touch keys can be combined. To do this, connect the relay to be
activated between the relay out1 (connected to +12 on one side) and output 2. Program the time of output 2 to enable entry of
the code on the keypad (15-30 seconds). Leave time 1 normally at approx. 1 sec. In this way, after placing the touch key on probe
2 enter the code on the keypad. The relay is only activated if both are valid.
NB2: All codes entered and not recognised are in any event sent (with the command “NOOPEN_SERR”) to the digital bus ( com-
bining them with the specific digibus number). This means they can be used to activate other additional devices by means of
types 170D-170F.
To effect a door lock release:
With display viewing:
<<<ß-------------à>>>
Enter code
(if not press first push-button “R”), to release the door lock enter one of the codes recorded in parameters from number xx to yy
and then press push-button “C”.
Attention: code 0 is not a number to be used to release the door lock.
To store the door codes, proceed as it follows:
- Enter the technical programming (push-buttons R + 4), then digit the programming “password” (default value: 123). NOTE:
first of all make sure the lock dip-switches (on the rear) are not in ON position (BLOCK.PRG).
- Scroll all parameters until you reach the key zones (on display appears the following message “CHIAVE Ser. N 001”). NOTE:
To by-pass all the parameter scrolling, press the “double arrow down” in order to reach the first key immediately).
- Scroll until you reach the key position to enter/modify (for example: “Chiave Ser. N 015” for the 15th key ).
- Enter the code to store (without initial zeroes and with a maximum of 8 digits).
- Confirm with push-button “C” to store it.
To exit the programming, press the “R” push-button.
Manual output time 4: This is the activation time of output 4 when activated directly by terminal T4 (closing to earth). This func-
tion is only useful in this specific operating mode (see below “operating mode”=64) and for output 4 only.
