em-vent EVSCP24-5 Instruction Manual

Technical Note
November 2014 | Version 1
Em-Vent Smoke Control Panel Single Zone 5Amp (EVSCP24-5)
Product Description
5Amp / 1 fire group and 1 comfort group.
Em-Vent smoke vent control panels are constructed to provide and control the operation of the opening
systems for comfort and fire ventilation with 24V DC electrical actuators.
The Em-Vent smoke control panel is equipped with connection terminals for external signals (comfort and
fire switched, weather sensor/close all, detectors, etc), and it is also possible to connect more control
panel in the same ‘Bus’ connection.
The Em-Vent smoke control panel has a compact and elegant design and is certified according to EN
12101-10 class A (double supply) and EN 12101-9 (draft). Incl. battery back-up.

Technical Note
November 2014 | Version 1
Specific Characteristics
Specifications
EVSCP24-5
Approvals / Conforms
EN 12101-10: 2005 approved and certified –class A (double
supply) –envir. Class 1 (to -15˚C)
Conform to EN 12101-9
Power Supply
230V AC –max 1.5A
Output Supply
24V DC
Motor Outputs
1 pc. (line detection: 1-4 lines)
Max Total Load
5A
Operating Temperature
-15˚C - +40˚C
Density
IP 54
Battery Back-up (72hrs)
Yes
Batteries
2 pcs. 12V7, 2AH
Dimensions (WxDxH)
Weight incl. Batteries
238x113x286mm
7.5kg
Colour
White Front / Grey Indication Label
Fire Groups
1 pc. with line detection
Max power consumption for fire switches (LED+Buzzer) = 6.6mA =
approx. 3 manual control points
Comfort Groups
1 pc. - unlimited no. of comfort switches
Detector (Smoke/Heat) Input
1 pc. with line detection
Max power consumption for detectors = 2.2mA = approx. 22
detectors
Weather Sensor Input / Close All
Yes
Alarm Output
Yes –potential free contact, max 48V / 0.5A
Failure Output
Yes –potential free contact, max 48V / 0.5A
24V DC for External Use
24V DC / max 0.5A –at 230V AC operation
Bus Communication
Yes –connection of 2-10 control panels –line detection
Visual (LED) Indication in Front Panel
‘OK’ / ‘AC Fault’ / ‘Low Battery’ / ‘Line Fault’ / ‘Alarm’ / ‘Comfort
Open’
DIP Switch Features (Standard)
Service hours (LED’s flash in front panel)
Comfort opening interval
Temperature detection via motor output
Extra line detection via 3 wire motor output
Fail safe (alarm by line failure)
Sprinkler (close by alarm)
Bus comm. settings (react on Bus comm.)
Potential free contact for comfort open

no 1
Manual control point,
Break glass (EVSMCP)
fit jumper in last
Manual control point,
Break glass (EVSMCP)
Place resistor in last detector
RED
Keyboard
DIP settings see page 13
BL
J15
J11
Without keyboard jumper mounted
J9
NTC
PS1
Power Supply 180-250 VAC
24VDC 150W/200W
24V Out
1 channel LIP
(LIP5/ LIP6)
example
CH 1
Actuator
Motor line monitor
Ext 3 wire monitor (line 1)
Actuator
5
LIP #1
5
LIP #1
Next LIP
6
34
Brown
M1
Next LIP
Brown 3
M1
6
4
2
Blue
2
Blue
1 1
L1PE
10 A Autofuse
3
N1
2
1
Line 1
21
J2
4 J3
FUSE F1 - fast
Max. 8A
Wind and rain sensor
Switch Ch 1
Nr.2-20
67
4
32
1
J1
680Ω
10 KΩ
67 43
2
1
Comfort
L1 Out
10 KΩ
(Close all)
Down
Smoke or
heat sensors
Potential free Failure switch.
Com + NC connected on failure. Max 48V 0,5A
Potential free ALARM switch.
Com + NO connected on alarm.
Max 48V 0,5A
Extra relay print 111655
provides 4 additional
potential free switches
each 30V 0,5A
Green LED
Yellow LED
Red LED
J1
4 762 31
10 KΩ
680Ω
Up
L2
L1 In
L2
Nr.1
L1 In
L1 Out 1 2
3 5
START TERM.
10
OK 24V
3
6
NO
4
COM
5
NC
Alarm Out Failure Out
8 9
NC
NO
7
COM
14
Reset
15
Gnd
FIRE
11 12
Fail. 24V
ALARM
24V
13
Down
19
Gnd
16
Smoke
17
Up
18
Set J11 for batteri backup
of terminal 23
J4
→
up to 35 pcs. control units.
Busconnection for serial connection
Connection from
Serial In
A2
24V
Gnd
Weather
22 23
Gnd
20 21
→
prev. unit.
A1
→
Connection to
next unit.
Serial Out
→
→
B2
B1
A3
END TERM.MASTER SLAVE
J7J6J5
→
B3
BUZZER
Red 2,5mm224V
Batteries 2x 12V - 7,2 /12 Ah
- 24VDC +
-
Black 2,5mm2
+
+
-
PS -
PS +
BLUE
DOME OPEN
START termination
OFF
→
21DIP NO
ON
→
BAT -
BAT +
YELYEL
AC FAIL LINE FAIL
RESET
YEL
variable
Puls
BATT LOW
Const.
Min
FAIL SAFE
Con. Fire. Sw
Potmeter for
comfort features
Max.
Puls
END termination
BUS Slave
BUS Master
109 1185 7643 12
BUS FIRE
BUS COMFORT
SPRINKLER
AG MODE
WEEK OPEN
FAIL RELAY M.
SNITCH
SERVICE TIMER
TEMP DETECT
DSW
LD1 Actuator open (red). Lit when actuator is opening.
LD2 Actuator closing (green). Lit when actuator is closing.
LD3 Weather sensor active (red). Lit when weather sensor is active.
LD4 Line failure actuator (red). Lit for line failure on actuator.
LD5 Line failure fire switch (red). Lit for line failure on fire switch.
LD6 Line failure smokesensor (red). Lit for line fail. on smokes.
LD7 BUS failure (red). Lit when local unit is not recieving signal.
RED GRE
RED RED
RED
RED RED
BUZZER ON/OFF
J1
FAILURE
YEL
OK
GRE
ALARM
Em-Vent Smoke Control Panel
EVSCP24-5
Connection to SVM Add-Onn
EVSCP24-8
2 3 4
OPEN
6
1
CLOSE
5
Firemans Priority Switch (EVSFPS)
61
Firemans Priority Switch
Remove resistors when
mounting Firemans Priority Switch
Connection diagram SVM Whitesales
Drawing: 211707 B
Wiring Diagram