Emerson Bettis RP4AF User manual

Bettis RTS Relay Board (RP4AF)
Electric Actuator
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 1
August 2023

Notes
August 2023
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 1
This page intentionally left blank.

Table of Contents
August 2023
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 1
Table of Contents i
Table of Contents
Section 1: Tools
Tools.......................................................................................................................................1
Section 2: Material
Material.................................................................................................................................2
Section 3: Installation
Installation............................................................................................................................3
Section 4: Programming
Programming.......................................................................................................................7

Notes
August 2023
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 1
This page intentionally left blank.

August 2023
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 1
Tools
Section 1: Tools
1
Section 1:Tools
! WARNING
Remove all power supplies before doing the exchange. Act always with caution
during the exchange!
• Needle nose pliers
• Screw driver phillips
• Screw driver at
• Allen key 5
• Socket wrench 5
Figure 1.

August 2023
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 1
Material
Section 2: Material
2
Section 2:Material
• 1x relay board RP4AF (ID:15772)
• 2x steel screw M3x16 (ID:952)
• 3x plastic distance 8 mm (ID:9896)
• 1x plastic screw M3x15 (ID:9895)
• 1x plastic nut M3 (ID:7084)
• 2x lock plates M3 red (ID:13674)
Figure 2.
Figure 3.

August 2023
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 1
Installation
Section 3: Installation
3
Section 3:Installation
1. Unscrew the 4 hexagon socket screws from the cover and remove it carefully.
Mind the connection cable between display and logic board.
Figure 4.
2. Unscrew the 4 cross recessed screws from the existing logic board and afterwards
tilt it carefully to you.
Figure 5.

August 2023
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 1
Installation
Section 3: Installation
4
3. Remove the cable with the 10-pole connector and connect it with the
relay board.
Figure 6.
4. Insert plastic screw M3x15 in provided hole and add plastic distance on it,
after connect the relay board with the logic board on suitable connector.
Add plastic nut on plastic screw to x the board.
Figure 7.

August 2023
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 1
Installation
Section 3: Installation
5
5. Put two plastic distances 8 mm between logic and relay board, insert the
M3x16 steel screws through the estimated holes in logic board, plastic
distances and relay board and secure the screws with the red lock plates.
Figure 8.
6. Install die logic + relay board back to the control (two small screws for
original installation will remain). Take care of possible damage of cables or
other parts.
Figure 9.

August 2023
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 1
Installation
Section 3: Installation
6
7. Connect cable between display cover and logic board. Perform a Firmware
update now, before installing display cover on the unit. This update is
important for the following programming steps (use FW version display 1507,
logic 219 or higher). For a detailed description on how to perform a rmware
update, please refer to separate manual.
During display cover installation, pay attention to the O-ring which must
sit correctly between cover and housing and x it with the 4 hexagon
socket screws.
Figure 10.