Emerson Bettis RTS FL Series User manual

User Instructions
MAN-02-04-60-0352-EN Rev. 3
February 2019
Operating Manual for Bettis RTS FL Series
Fail-Safe Linear Electric Actuator

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
Table of Contents
i
Table of Contents
Table of Contents
Section 1: Introduction
Section 2: Functional Description of the
RTS FL Fail-Safe Linear Actuator
2.1 Fail-Safe Direction ......................................................................................... 3
2.2 Option Manual Override................................................................................ 3
Section 3: General Information
3.1 Safety Instructions ........................................................................................ 5
3.2 Serial Number and Type Label ....................................................................... 5
3.3 Operating Mode............................................................................................ 6
3.4 Protection Class ............................................................................................ 6
3.5 Mounting Position......................................................................................... 7
3.6 Direction of Rotation..................................................................................... 7
3.7 Protection Devices ........................................................................................ 8
3.8 Ambient Temperature................................................................................... 8
3.9 Delivery Condition of the Actuators .............................................................. 8
3.10 Information Notice (Tag) ............................................................................... 9
Section 4: Packaging, Transport and Storage
4.1 General ....................................................................................................... 10
4.2 Storage ....................................................................................................... 10
4.3 Long-term Storage...................................................................................... 11
Section 5: Installation Instructions
5.1 Mechanical Connection............................................................................... 12
5.2 Mounting of Linear Fail-Safe Actuator.......................................................... 13
5.3 Mounting Position of the Operating Unit..................................................... 16
5.4 Electrical Connection .................................................................................. 17
Section 6: Commissioning
6.1 General Information.................................................................................... 20
6.2 Manual Operation ....................................................................................... 20
6.3 Mechanical Default Settings and Preparation .............................................. 21
6.4 End Limit Setting......................................................................................... 22
6.5 Adjusting of Fail-Safe Speed ........................................................................ 28
6.6 Final Step .................................................................................................... 30

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
Table of Contents
ii Table of Contents
Section 7: Control Unit
7.1 Operating Unit ............................................................................................ 31
7.2 Display Elements......................................................................................... 32
7.3 Operation ................................................................................................... 34
Section 8: Parameter Menu
8.1 Parameter Group: End Limit ........................................................................ 43
8.2 Parameter Group: Torque............................................................................ 45
8.3 Parameter Group: Speed ............................................................................. 46
8.4 Parameter Group: Ramp (optional) ............................................................. 46
8.5 Parameter Group: Control ........................................................................... 47
8.6 Parameter Group: Password ........................................................................ 47
8.7 Parameter Group: Position .......................................................................... 48
8.8 Parameter Group: Binary Inputs .................................................................. 49
8.9 Parameter Group: Binary Outputs ............................................................... 52
8.10 Parameter Group: Position Output (optional).............................................. 56
8.11 Parameter Group: Step Mode ...................................................................... 57
8.12 Parameter Group: Positioner (option).......................................................... 59
8.13 Parameter Group: PID Controller (optional)................................................. 61
8.14 Parameter Group: Characteristic Curves (optional)...................................... 63
8.15 Parameter Group: Identication (option)..................................................... 64
8.16 Parameter Group: System Parameters (locked) ........................................... 64
8.17 Parameter Group: Miscellaneous................................................................. 65
Section 9: Status Area
9.1 Status.......................................................................................................... 66
9.2 History........................................................................................................ 69
Section 10: Infrared Connection
Section 11: Bluetooth Link
Section 12: Maintenance
Section 13: Troubleshooting
13.1 Error List...................................................................................................... 73

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
Table of Contents
iii
Table of Contents
Section 14: Fuses
Section 15: Lubricant Recommendations and Requirements
15.1 Main Body: -25oC to +60oC.......................................................................... 76
15.2 Main Body: -40oC to +60oC.......................................................................... 76
15.3 Output type A and spindle drives (Linear Actuators) -40 to +60C................. 76
15.4 Basic Lubricant Service Interval ................................................................... 76
Section 16: Training
Section 17: Technical Data and Certifications
17.1 Binary Outputs............................................................................................ 79
17.2 Binary Inputs............................................................................................... 80
17.3 Analog Inputs.............................................................................................. 84
17.4 Analog Output ............................................................................................ 84
17.5 Auxiliary Voltage Input and Output ............................................................. 86
17.6 Connections ............................................................................................... 87
17.7 Miscellaneous ............................................................................................. 87

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
1
Section 1: Introduction
Introduction
Section 1: Introduction
Bettis RTS FL Fail-Safe electric actuators are designed to operate appropriate valves when a
fail-safe functionality is required.
Appropriate valves are all kind of valves that require a linear movement to operate
(globe valve, gate valves, etc.).
In the event of a power failure or if the fail-safe function is triggered deliberately, the linear
Actusafe actuator shifts the valve to the fail-safe position, using the built-in energy storage
device to do so.
Figure 1 Bettis RTS FL Fail-Safe Electric Actuator

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
2
Section 2: Functional Description of the RTS FL Fail-Safe Linear Actuator
Functional Description of the RTS FL Fail-Safe Linear Actuator
Section 2: Functional Description of the
RTS FL Fail-Safe Linear Actuator
In normal operation, the actuator is operated by a PM motor (1). Via a worm gear stage (2)
and a planetary gear train (3), the motor drives the spindle nut of a ball screw (4). The sun
gear shaft of the planetary gear train is xed in place by an operating current brake (5).
The ball screw converts the rotational movement of the gear unit into linear motion, which,
on the one hand, charges the spring packet (6), which acts as an energy storage device.
On the other hand, the linear motion is transmitted to the valve stem (8) via a
spring-loaded spindle pin (7).
There are no engaging or disengaging elements between the motor, the energy storage device
and the tting shaft in the actuator. All the gear unit components are permanently engaged.
While moving against the fail-safe direction, the electric motor has to move both the valve
and the energy storage device (disk spring assembly) for the fail-safe stroke.
If the supply for the operating current brake is interrupted (by a power failure, or
intentionally to trigger a fail-safe stroke, the actuator will no longer be held, and the energy
stored in the disk spring packet will be converted into kinetic energy so as to move the
actuator and thus the valve to the fail-safe position. In this situation, the entire gear chain
of the actuator with the exception of the worm gear stage will be moved until the end
stop of the valve is reached. The spring-loaded spindle pin (7) dampens the stop and thus
protects the valves seat.
Owing to this operating principle, neither an initialising stroke nor resetting of the drive
is required after a fail-safe stroke. As soon as the power supply is restored, the actuator is
immediately ready for operation.
Figure 2 Cutaway View of RTS FL Fail-Safe Linear Actuator

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
Section 2: Functional Description of the RTS FL Fail-Safe Linear Actuator
3Functional Description of the RTS FL Fail-Safe Linear Actuator
Parts Overview:
1. Motor
2. Worm Gear Stage
3. Planetary Gear Train
4. Ball Screw
5. Operating Current Brake
6. Spring Packet
7. Spring Loaded Spindle Pin
8. Valve Stem
2.1 Fail-Safe Direction
This type of fail-safe actuator can be built in two versions for "Fail-Safe Close"
(extend actuator stem) or "Fail-Safe Open" (retract actuator stem).
2.2 Option Manual Override
RTS FL actuator can additionally be equipped with a manual mode. This additional option
allows an adjustment of the valve in deenergized state.
CAUTION: MANUAL MODE OPERATION
- By activating the manual drive the fail-safe function is disabled.
- By activating the manual drive the electrical function of the drive is disabled.
In normal operation, the handwheel (9) is not engaged. By pushing the coupling rod (10),
the handwheel is engaged and at the same time, disables the actuator electrically (switched
to malfunction) and the fail-safe function. By using a padlock, the actuator can be protected
against unintended manual operation or inadvertent activation of manual operation.

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
4
Section 2: Functional Description of the RTS FL Fail-Safe Linear Actuator
Functional Description of the RTS FL Fail-Safe Linear Actuator
Figure 3 RTS FL Fail-Safe Linear Actuator with Padlock
9
11
10
Parts Overview:
1. Handwheel
2. Coupling Rod
3. Padlock

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
5
Section 3: General Information
General Information
Section 3: General Information
3.1 Safety Instructions
CAUTION: WORK UNDER GUIDANCE AND SUPERVISION
When operating electrical devices, certain parts are inevitably under dangerous voltage.
Work on the electrical systems or components may only be carried out by electricians or by
individuals who have been instructed how to do so. Working under the guidance and
supervision of an electrician in accordance with electrotechnical regulations.
WARNING: ALWAYS REFER TO STANDARDS
When working in potentially explosive areas, pay attention to European Standards EN 60079-14
“Installing Electrical Systems in Explosion Endangered Areas” and EN 60079-17 “Inspection and
Maintenance of Electrical Installations in Explosion Endangered Areas”.
Working in potentially explosive areas is subject to special regulations (European Standard EN
60079-17), which must be complied with. Any additional national regulations must be needed.
3.2 Serial Number and Type Label
Each actuator of the RTS Fail-Safe Linear FL series carries a serial number. The serial number
begins with the year and that can be read from the type label (see Figure 4) of the actuator
(the type label is located next to the handwheel – see Figure 5).
Using this serial number, Emerson can uniquely identify the actuator (type, size, design,
options, technical data and test report).
Figure 4 Bettis RTS Tag and Serial Number
181148
/
1
No.: 18113E04559
Type: FL-15B-1MHHB
0,21-6,0mm/sec
50,0mm 8,3-240sec
IP68
Open: 15,0kN
Close: 15,0kN
TÜV-A16ATEX0007X
Tamb-40..+60°C
2018
II 2 G Ex de IIC T4 Gb
S2-15min
1026
S4-1200c/h - 40%ED
3x380-480V 50/60Hz
0,84-0,67A
I :
NLC16.13198-1S
AEx de IIC T4 Gb
19200 Northwest Fw
y,
Houston
,
TX 77065
Class 1 Div 1 & 2 Group A
IECEx LC 17.0003X
Ex de IIC T4 Gb

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
66
Section 3: General Information
General Information
Figure 5 Label 1 - Type Label
1
3.3 Operating Mode
RTS Fail-Safe Linear FL actuators are suitable for open-loop control (S2 operating mode -
on/off duty) and closed-loop control (S9 operating mode - modulating duty) according to
EN 60034-1.
3.4 Protection Class
RTS Fail-Safe Linear FL actuators come by default with IP 68 (EN 50629) protection.
CAUTION: PROTECTION CLASS AND CABLE GLANDS
The protection class specied on the type label is only effective when cable glands also
provide the required protection class, the cover of the connection compartment is carefully
secured and the mounting position (see Section 3.5) is observed.
We recommend metallic threaded cable glands with a metrical thread. Unused cable inlets
must be closed with stopping plugs. On explosion-proof actuators, cable glands with
protection class EEx e according EN60079-7 must be used. After removing covers for
assembly purposes or adjustment work, take special care upon reassembly so that seals are
not damaged and remain properly fastened. Improper assembly may lead to water ingress
and to failures of the actuator.
NOTE:
The cover of the control unit - the Operating unit - (see Figure 1) must not be opened.
Allow a certain sag in the connector cables before reaching the screwed cable glands so that
water can drip off from the connector cables without running to the screwed cable glands.
As a result, forces acting on the screwed cable glands are also reduced. (see Section 3.5)

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
7
Section 3: General Information
General Information
3.5 Mounting Position
Generally, the installation position is irrelevant. However, based on practical experience, it
is advisable to consider the following for outdoors use or in splash zones:
• Mount actuators with cable inlet facing downwards
• Ensure that sufcient cable slack is available
3.6 Direction of Rotation
Unless specically ordered otherwise, the standard direction is (see Figure 6 and Figure 7):
• Right turning (clockwise) = CLOSING
• Left turning (counter clockwise) = OPENING
Figure 6 Clockwise = Close
Figure 7 Counterclockwise = Close

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
88
Section 3: General Information
General Information
CAUTION: OBSERVE DIRECTION OF ROTATION
All specications in this operating manual refer to the standard direction of rotation.
3.7 Protection Devices
3.7.1 Torque
RTS Fail-Safe Linear FL actuators provide electronic torque monitoring.
The switch off torque can be modied in the menu of the controller for each
direction separately. By default, switch off torque is set to the ordered value. If no
torque was specied with the order, the actuator is supplied from the factory with
the maximum congurable torque.
For more information, (see Section 8.2).
3.7.2 Motor Temperature
All RTS Fail-Safe Linear FL actuators are normally equipped with motor winding
temperature sensors, which protect the motor against excessive winding
temperature.
The display will show the corresponding error upon exceeding the permissible
motor temperature (see Section 3.1).
3.7.3 Input fuse, thermal fuse
The frequency inverter is protected by an input fuse and the explosion proof
version by a thermal fuse. If one of the fuses releases, a serious defect occurs and
the frequency inverter must be replaced.
3.8 Ambient Temperature
Unless otherwise specied upon ordering, the following operating temperatures apply:
• On/off duty (open-loop control) -25 to +60°C
• Modulating duty (closed-loop control) -25 to +60°C
• Explosion-proof version -20 to +40°C (acc. EN60079-0)
• Explosion-proof version with extended temperature range -40 to +60°C
CAUTION: OBSERVE OPERATING TEMPERATURE
The maximum operating temperature can also depend on further order-specic components.
Please refer to the technical data sheets to conrm the as-delivered product specications.
3.9 Delivery Condition of the Actuators
For each actuator, an inspection report is generated upon nal inspection. In particular, this
comprises a full visual inspection, calibration of the torque measurement in connection
with an extensive run examination and a functional test of the microcontroller.
These inspections are conducted and documented according to the quality system and can
be made available if necessary. The basic setting of the end position must be performed
after assembly on the actuator.

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
9
Section 3: General Information
General Information
CAUTION: OBSERVE COMMISSIONING INSTRUCTIONS
Commissioning instructions (see Section 5) must be strictly observed. During assembly
of the supplied valves at the factory, end postions are set and documented by attaching a
label (see Figure 8). During commissioning at the plant, these settings must be veried.
3.10 Information Notice (Tag)
Each actuator is provided with a bilingual tag containing key information, which is attached
to the handwheel after nal inspection. This tag also shows the internal commission
registration number (see Figure 8).
Figure 8 Tag

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
10
Section 4: Packaging, Transport and Storage
Packaging, Transport and Storage
Section 4: Packaging, Transport and Storage
Depending on the order, actuators may be delivered packed or unpacked. Special
packaging requirements must be specied when ordering. Please use extreme care when
removing or repackaging equipment.
CAUTION: USE APPROPRIATE LIFTING EQUIPMENT
Use soft straps to hoist the equipment; do not attach straps to the handwheel.
If the actuator is mounted on a valve, attach the straps to the valve and not to the actuator.
4.1 General
The connection compartment of RTS Fail-Safe Linear FL actuators contains 5g of factory
supplied silica gel.
CAUTION: REMOVE SILICA GEL
Please remove the silica gel before commissioning the actuator (see Section 6).
4.2 Storage
CAUTION: OBSERVE PROPER STORAGE
- Store actuators in well-ventilated, dry premises
- Protect against oor dampness by storing actuators on wooden grating, pallets,
mesh boxes or shelves
- Protect the actuators against dust and dirt with plastic wrap
- Actuators must be protected against mechanical damage
- The storage temperature must be between -20°C - +40°C
It is not necessary to open the controller of the actuator for servicing batteries or
similar operations.

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
11
Section 4: Packaging, Transport and Storage
Packaging, Transport and Storage
4.3 Long-term Storage
CAUTION: 6 MONTHS OF STORAGE
If you intend to store the actuator for over 6 months, also follow the instructions below:
- The silica gel in the connection compartment must be replaced after 6 months of
storage (from date of delivery)
- After replacing the silica gel, brush the connection cover seal with glycerine.
Then, carefully close the connection compartment again
- Coat screw heads and bare spots with neutral grease or long-term
corrosionprotection
- Repair damaged paintwork arising from transport, improper storage,
or mechanical inuences
- For explosion-proof actuators, it is not allowed to extensively overpaint the actuator.
According to the standard, in order to avoid electrostatic charge, the maximum
thickness of the varnish paint is limited to 200 µm.
- Every 6 months. all measures and precautions for long term storage must be
checked for effectiveness and corrosion protection and silica gel renewed
- Failure to follow the above instructions may lead to condensation which can damage
to the actuator

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
12
Section 5: Installation Instructions
Installation Instructions
Section 5: Installation Instructions
Installation work of any kind of actuator may only be performed by qualied personnel.
5.1 Mechanical Connection
Check:
• Whether valve ange and actuator base match-up.
• If the bore of the coupling piece coincides with the spindle pin and sufcient
thread engagement is available.
Make sure the tting is in the same position as the actuator:
• For a “fail-safe opener” actuator, the valve has to be completely open.
• For a “fail-safe closer” actuator, the valve has to be completely closed.
In general, refer to the following instructions:
• Clean the bare parts on the actuator coated with rust protectant.
• Clean the mounting surface for the tting thoroughly.
• Lightly grease the valve stem.
• Set the actuator in place.
• Make sure of centered positioning and that the contact surface of the ange is full.
• Fasten the actuator with suitable bolts:
— Minimum strength grade: 8.8 or A2-70
— Ensure sufcient thread engagement (min. 1xd)
CAUTION: AVOID USING TOO LONG SCREWS
Screws that are too long may go against the thread root, creating the risk of the actuator
moving radially in relation to the tting. This may lead to the bolts shearing off.
NOTE:
Unsuitable bolts may result in the actuator falling off.
• Tighten bolts to the correct torque, alternating between bolts on opposite sides.

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
13
Section 5: Installation Instructions
Installation Instructions
Table 1. Thread Table (1)
Thread Tightening Torque [Nm] for Bolts with Strength Grade
8.8 A2-70 / A4-70
M6 11 8
M8 25 18
M10 51 36
M12 87 61
M16 214 150
M20 431 294
M30 1489 564
CAUTION: PREVENT ACTUATOR OVERSPEEDING
Valve or piping may be damaged due to high actuating speed.
5.2 Mounting of Linear Fail-Safe Actuator
Emerson Bettis RTS FL Fail-Safe Linear electric actuators move the stem of valve to the
failsafe position in case of failsafe event. In general stem of actuator is at failsafe position at
delivery! epending on valve has to be closed or opened by force (sealing force is required
in Failsafeposition) or by travel (actuator shall stop before touching the seat), mounting
procedure has to be done different:
5.2.1 Mounting procedure for valve without required sealing force:
• Connect mounting kit to valve and x according valve producer specication
• Be sure stem of valve is exact in desired failsafe end position
• Be sure stem of actuator is in failsafe position: actuator must not be electrically
connected. Handwheel must not be engaged (if applicable, refer to Section 6.2
Manual Operation)
• Mount actuator to mounting kit and x with 4 screws
• Check distance between end of stem of actuator and end of stem of valve:
allowed range of distance is 2 – 25mm
• Connect both stems with coupling and note symmetrical engagement of
both threads
• Fix coupling with 4 screws and note both halfs of coupling have to be parallel after
tighten the screws

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
14
Section 5: Installation Instructions
Installation Instructions
Figure 9 Linear Fail-Safe (1)
5.2.2 Mounting procedure for valve with required sealing force:
• Connect mounting kit to valve and x according valve producer specication
• Be sure stem of valve is exact in desired failsafe end position
• Stem of actuator has to be moved 2-5mm away from failsafe position by using
handwheel (if applicable, refer to Section 6.2 Manual Operation)
If actuator is not equipped with hanwheel switch to alternative procedure
• Mount actuator to mounting kit and x with 4 screws
• Check distance between end of stem of actuator and end of stem of valve:
allowed range of distance is 2 – 25mm
• Connect both stems with coupling and note symmetrical engagement of
both threads
• Fix coupling with 4 screws and note both halfs of coupling have to be parallel after
tighten the screws

User Instructions
MAN-02-04-60-0352-EN Rev. 3 February 2019
15
Section 5: Installation Instructions
Installation Instructions
5.2.3 Alternative procedure for valve with required sealing force:
• Connect mounting kit to valve and x according valve producer specication
• Be sure stem of valve is exact in desired failsafe end position
• Loosen hexagonal nuts of mounting kit and generate a gap of 3-5 mm between
ange and pillar
• Mount actuator to mounting kit and x with 4 screws
• Check distance between end of stem of actuator and end of stem of valve:
allowed range of distance is 2 – 25mm
• Connect both stems with coupling and note symmetrical engagement of
both threads
• Fix coupling with 4 screws and note both halfs of coupling have to be parallel after
tighten the screws
• Finally retighten hexagonal nuts symmetrical until gap disappears
Attention: Actuator must not be electrically connected! And handwheel must not
be engaged (if applicable, refer to Section 6.2 Manual Operation)
Figure 10 Linear Fail-Safe (2)