Emerson ClosetMaid ShelfTrack Assembly instructions

ShelfTrack®Installation Tips
1. Use the correct hardware
Select the hardware that is right for your wall type:
2. Hang track location
Track can be installed at any height. However, for maximum
adjustability and strongest installation, install track flush to
ceiling and screw into wood header behind wallboard. Stud
installation is recommended whenever possible for the strongest
installation.
3. Determine length and spacing of standards
Standards are available in several lengths, depending on the number
of shelves you want and the spacing between the shelves. The closer the
standards are placed together, the stronger the installation. Standards
should be spaced no more than 24 in. apart, and no more than 4 in.
from the end of the shelf.
4. Securing standards
Each standard must be secured to the wall with one screw at the closest
hole to the center of the standards. When using toggle bolts, remove
toggle, put bolt through standard and re-attach toggle to bolt before
placing standard on track.
5. Attaching brackets
Attach brackets at desired shelf height.
NOTE: Always match bracket size to shelving depth except when using
Shelf & Rod shelving. Always use 12 in. brackets for this type of shelving. When
installing 16 in. SuperSlide®with Closet Rod & Support always use 12 in. brackets.
6. Cutting shelving, closet rods, and hang tracks
Wire shelving can be cut using a bolt cutter or hacksaw.
Closet rods can be cut using a pipe cutter (recommended) or a
hacksaw. Hang tracks can be cut with a hacksaw.
7. Corners
When two shelves come together in a corner, use a corner shelf support
to connect them. Use a corner closet rod to allow clothes to slide
uninterrupted around corners.
NOTE: SuperSlide®Closet rod supports should be placed where closet rods join.
8. End caps
Add caps to every exposed wire on both ends of each
shelf and to the ends of closet rods. End caps protect
you, your clothing and the shelving materials.
with
A D
B E
C F
G
Hang Track
Standard
Bracket
Closet Rod
Closet Rod Support
Closet Rod End Cap
Shelf End Cap
Choose Your Hardware
Drywall
Drill 1/2 in. holes and
secure to the wall with
toggle bolts.
Studs
Secure to the wall with #12
x 2 in. pan head screws at
stud locations.
Concrete
Drill 1/4 in. holes. insert
#12 wall anchors and
secure to the wall with #12
x 2 in. pan head screws.
24 in. maximum
F
E
D
C
B
G
24in.
61cm
A
ClosetMaid.com |1-800-874-0008 |10/13

Fixed Mount Installation Tips
1. Shelf installation
There are three ways to install a shelf: Wall-to-Wall, Wall-to-Open,
Open-to-Open. Shelves are supported by wall clips and support
brackets or support poles. When a shelf is attached to a side
wall, a wall bracket is also used.
Choose the right hardware based on the length of the shelf and
whether or not it attaches to a side wall.
2. Use the right hardware
Drywall - Use ClosetMaid hardware with attached anchor in drywall
that is 5/8 in. thick or less. Drill 1/4 in. hole, insert hardware, and push
in pin using the blunt end of a hammer or screwdriver. Punching the holes
in the wall or drilling oversized holes will result in a weakened installation.
Hammering pins into the wall can result in broken hardware.
Wood studs - Cut attached anchor off of ClosetMaid hardware and
secure to the wall using a #8 x 1 in. screw into the stud.
Concrete (all) and plaster or drywall (over 5/8 in. thick) - Drill
1/4 in. hole, insert hardware with attached anchor, and secure to the
wall using a #8 x 1 in. screw.
3. End caps
Add caps to every exposed wire on both ends of each shelf and to the
ends of closet rods. End caps protect you, your clothing and the shelving
materials.
Wall-to-Wall Wall-to-Open Open-to-Open
4. Corners
Butt shelves (A). Be sure to allow for the width of the full length shelf
when calculating the size of the other shelf. Use a corner support to
connect the two shelves. Use a corner hanger bar to connect hanger
bars and allow clothes to slide around corners. Or use a corner kit (B)
that includes a specially designed corner shelf, corner hanger
bar, and all installation hardware.
NOTE: Hanger bar supports should be placed where hanger bars join.
5. Measuring and cutting shelves and hanger bars
Wire shelving can be cut using a bolt cutter or hacksaw. Hanger bars
can be cut using a pipe cutter.
A. B.
6. Using 16 in. shelving
16 in. shelving provides additional storage capacity. It is especially
good for storage of linens or boxes and as shoe shelving. Hanger bars
can be installed using 16 in. shelving. When using 16 in. shelving to hang
clothes, be sure to use 12 in. support brackets as shown so the shelf is
supported properly and hangers can slide unobstructed.
7. Alternative hardware
Support poles instead of support bracket when stacking
two or more shelves.
A D
B E
C F
G
Support Bracket
Side Wall Bracket
Wall Clip
Closet Rod
Closet Rod Support
Closet Rod End Cap
Shelf End Cap
Choose Your Hardware
F
E
D
B
A
12 in.
30,5 cm
C
G
ClosetMaid.com |1-800-874-0008 |10/13