Emerson Rosemount 405 User manual

Quick Start Guide
00825-0100-4810, Rev HA
June 2016
Rosemount™405 Compact Primary
Element
00825-0100-4810_RevHA.fm Page 1 Friday, June 17, 2016 3:15 PM

June 2016
2
Quick Start Guide
NOTICE
This guide provides basic guidelines for Rosemount 405. It does not provide instructions for configuration,
diagnostics, maintenance, service, troubleshooting, Explosion-proof, Flameproof, or intrinsically safe (I.S.)
installations. Refer to the Rosemount 405 Reference Manual (document number 00809-0100-4810) for
more instruction. This manual is also available electronically on www.rosemount.com.
If the Rosemount 405 was ordered assembled to a Rosemount 3051S Transmitter, the new assembly is the
Rosemount 3051SFC Compact Flowmeter. See the following Quick Start Guide for information on
configuration and hazardous locations certifications: Rosemount 3051S Series Pressure Transmitter
(document number 00825-0100-4801).
If the Rosemount 405 was ordered assembled to a Rosemount 3051S MultiVariable™Transmitter, the new
assembly is the Rosemount 3051SFC Compact Flowmeter. See the following Quick Start Guide for
information on configuration and hazardous locations certifications: 3051S MultiVariable Transmitter
(document number 00825-0100-4803).
Process leaks may cause harm or result in death.
To avoid process leaks, use only gaskets designed to seal with the corresponding flange and O-rings to seal
process connections.
To ensure correct operation download the most current version of the Engineering Assistant software at:
EmersonProcess.com/en-US/brands/rosemount/Pressure/Pressure-Transmitters/MultiVariable-Transmitters/
3051S-MultiVariable/engineering-assistant6/Pages/index.aspx.
Contents
Primary element location . . . . . . . . . . . . . 3
Primary element orientation . . . . . . . . . . 5
Primary element installation . . . . . . . . . 10
Product certifications . . . . . . . . . . . . . . . 13
00825-0100-4810_RevHA.fm Page 2 Friday, June 17, 2016 3:15 PM

Quick Start Guide
3
June 2016
1.0 Primary element location
Install the Rosemount 405 in the correct location within the piping branch to
prevent inaccurate measurement caused by flow disturbances.(1)(2)(3) (4)
1
1. Consult an Emerson™Process Management representative if a disturbance is not listed.
2. If using flow straighteners, refer to ISO 5167 for recommended links.
3. Use straightening vane to reduce the required straight run length.
4. In plane means the Rosemount 405 is in the same plane as the elbow. Out of plane means the bar is
perpendicular to the plane of the upstream elbow. Refer to Figure 1 on page 4.
Table 1. 405C Straight Pipe Requirements(1)
Beta 0.40 0.50 0.65
Upstream (inlet)
side of primary
Reducer 2 2 2
Single 90° bend or tee 2 2 2
Two or more 90° bends in the same plane 2 2 2
Two or more 90° bends in different planes 2 2 2
Up to 10° of swirl 2 2 2
Butterfly valve (75% to 100% open) 2 5 5
Downstream (outlet) side of primary 2 2 2
Table 2. 405P Straight Pipe Requirements(1)(2)
Beta 0.40 0.50 0.65
Upstream (inlet)
side of primary
Reducer 5 8 12
Single 90° bend or tee 16 22 44
Two or more 90° bends in the same plane 10 18 44
Two or more 90° bends in different planes 50 75 60
Expander 12 20 28
Ball/gate valve fully open 12 12 18
Downstream (outlet) side of primary 6 6 7
Table 3. 405 Straight Run Requirements(1)
Without
straightening vane With straightening vane(3)
Annubar™averaging pitot tube - sensor
size 1
In
plane(4)
Out of
plane(4)
From
disturbance
From
straightening
vane
Upstream (inlet)
side of primary
Reducer 12 12 8 4
Expander 18 18 8 4
Single 90° bend or tee 8 10 8 4
Two or more 90° bends in the same plane 11 16 8 4
Two or more 90° bends in different planes 23 28 8 4
Butterfly Valve (75–100% open) 30 30 8 4
Ball/Gate Valve fully open 810 8 4
Downstream (outlet) side of primary 4 4 4 4
00825-0100-4810_RevHA.fm Page 3 Friday, June 17, 2016 3:15 PM

June 2016
4
Quick Start Guide
Note
Recommended lengths are represented in pipe diameters. If longer lengths of straight run
are available, position the Rosemount 405 so 80% of the pipe run is upstream and 20% is
downstream.
Flow conditioners may be used to reduce the required straight run length, improving
performance.
Figure 1. Compact Annubar Flowmeter In Plane and Out of Plane
Note
The above figure depicts in plane and out of plane orientations only. Refer to Table 3 on
page 3 for recommended straight run requirements.
1.1 Vibration limits for Rosemount 405 products
Qualified per IEC61298-3 (2008) for field with general application or pipeline with
low vibration level (10–1000 Hz test frequency range, 0,15 mm displacement
peak amplitude, 20 m/s2acceleration amplitude)(1).(1)
The weight and length of the transmitter assembly shall not exceed 9.8 lb
(4,45 kg) and 8.60-in. (218,44 mm).
1. Stainless steel temperature housing is not recommended with primary element technology A in applications with
mechanical vibration.
FLOW
FLOW
FLOW
FLOW
FLOW
In plane Out of plane
00825-0100-4810_RevHA.fm Page 4 Friday, June 17, 2016 3:15 PM

Quick Start Guide
5
June 2016
2.0 Primary element orientation
The primary element can be installed in any position around the circumference of
the pipe, provided the vents are positioned properly for bleeding or venting.
Optimal results for liquid or steam in a vertical line are obtained when flow is up.
Liquid - 405C, 405P, and 405A
Figure 2. Direct Mount
A. Recommended zone 30°
Figure 3. Remote Mount
Horizontal liquid
Horizontal liquid Vertical liquid
45° 45°
30°
AA
FLOW
00825-0100-4810_RevHA.fm Page 5 Friday, June 17, 2016 3:15 PM

June 2016
6
Quick Start Guide
Gas - 405C, 405P, and 405A
Figure 4. Direct Mount
A. Recommended zone 90°
Figure 5. Remote Mount
Horizontal gas Vertical gas
Horizontal gas Vertical gas
45° 45°
A
360°
Flow
FLOW
00825-0100-4810_RevHA.fm Page 6 Friday, June 17, 2016 3:15 PM

Quick Start Guide
7
June 2016
Steam - 405C, 405P, and 405A
Figure 6. Direct Mount
A. Recommended zone 30°
Figure 7. Remote Mount
Note
For the Rosemount 405A model in steam applications, with DP readings in a low flow
condition as low as 0.75 inH2O in horizontal pipes consider installing the primary
element/flowmeter in the top mounting for steam configuration.
Horizontal steam
Horizontal steam Vertical steam
45° 45°
30°
AA
FLOW
00825-0100-4810_RevHA.fm Page 7 Friday, June 17, 2016 3:15 PM

June 2016
8
Quick Start Guide
Top mounting for steam
Top mounting in steam is an alternative mounting method for steam installations
that can be used if there are space restrictions or other concerns. This installation
method is intended for applications that run with limited interruptions or
shutdowns. Also, for outdoor applications, top mounting can eliminate the need
for heat tracing, if steam is flowing.
Figure 8. Direct mount — 405C, 405P, and 405A
A. Recommended zone 60°
Note
For the Rosemount 405A Model in wet steam applications, do not mount the flowmeter at
the direct vertical position. Mounting at an angle will avoid measurement inaccuracy due to
water running along the bottom of the pipe.
Horizontal top mounting for steam up to 400 °F (204 °C)
60° 60°
A
00825-0100-4810_RevHA.fm Page 8 Friday, June 17, 2016 3:15 PM

Quick Start Guide
9
June 2016
Figure 9. Remote mount up to 850 °F (454 °C) – 405C, 405P, and 405A
Note
When top mounting with a remote mount transmitter, use enough impulse piping to
dissipate the process heat to avoid damaging the transmitter.
Suggested top mounting orientations:
For steam up to 400 °F (204 °C) use direct mount orientation and for steam up
to 850 °F (454 °C) use remote mount orientation.
For direct mounting, ambient temperature should be less than 100 °F (38 °C).
For remote mount installations, the impulse piping should slope up slightly
from the instrument connections on the Rosemount 405A Model to the cross
fittings, allowing condensate to drain back into the pipe.
From the cross fittings, the impulse piping should be routed downward to the
transmitter and the drain legs. The transmitter should be located below the
instrument connections of the Rosemount 405A Model.
For technologies C, P, and A, depending on the environmental conditions, it may
be necessary to insulate the mounting hardware.
00825-0100-4810_RevHA.fm Page 9 Friday, June 17, 2016 3:15 PM

June 2016
10
Quick Start Guide
3.0 Primary element installation
1. Orient the assembly according to the guidelines provided in “Primary element
orientation” on page 5. Ensure the flow arrow stamped on the
405 Primary Element is pointing in the same direction as the process flow.
Note
ANSI 150 - 600# alignment ring is included as standard when ordering for up to 8-in. line
sizes. For the 10-in. and 12-in. line size, the alignment ring must be ordered (Installation
Accessories). If a DIN or JIS alignment ring is required, it must be ordered as an option.
Contact an Emerson Process Management sales representative for additional information.
Note
For ease of installation, the gasket may be secured to the flange face with small pieces of
tape. Be sure the gasket or tape does not protrude into the pipe.
2. If using an alignment ring with through holes, proceed to Step 9.
3. Insert two studs through the flange holes located opposite the head of the
Rosemount 405.
4. Place the alignment ring on the Rosemount 405 body (see Figure 10 ).
5. Insert gaskets.
6. Insert the Rosemount 405 between the flanges so the indentations on the
alignment ring contact the installed studs. The studs must contact the
alignment ring in the indentation marked with the appropriate flange rating
to ensure proper alignment.
7. Install remaining studs and nuts (hand tight). Ensure three of the studs are in
contact with the alignment ring.
8. Lubricate studs and tighten nuts in a cross pattern to the appropriate torque
per local standards.
Step 9 through Step 12 are for use with alignment rings that have through holes.
9. Place the alignment ring on the Rosemount 405 body (see “Horizontal gas” on
page 6).
10. Insert the Rosemount 405 between the flanges.
a. Starting on the side opposite the Rosemount 405 head, rotate the
alignment ring such that the radius corresponding to the alignment ring
marking matches that of the application flange rating.
b. Insert one stud through both the upstream and downstream flanges and
allow the ring to rest on the bolt. This will ensure proper alignment.
11. Repeat Step 10 for the installation of the remaining bolts that will contact the
alignment ring.
12. Insert gaskets.
13. Install remaining studs and nuts (hand tight). Ensure three of the studs are in
contact with the alignment ring.
14. Lubricate studs and tighten nuts in a cross pattern to the appropriate torque
per local standards.
00825-0100-4810_RevHA.fm Page 10 Friday, June 17, 2016 3:15 PM

Quick Start Guide
11
June 2016
Note
Standard 1/16-in. gaskets are recommended for use with the Rosemount 405. Using other
gaskets could potentially cause a bias shift in the measurement.
3.1 Recommended insulation guidelines
For flowmeters with integral temperature assembly:
It is recommended that the meter be insulated when the difference between
process and ambient temperature is greater than 30 °F (16.6 °C).
1. For line sizes 1/2-in. (15 mm) to 4-in. (100 mm), it is recommended to have
4-in. (100 mm) of insulation of at least a 4.35 R-factor.
2. For line sizes 6-in. (150 mm) to 12-in. (300 mm), it is recommended to have
5-in. (125 mm) of insulation of at least a 4.35 R-factor.
The full thickness stated above may not be necessary for the entire flowmeter,
but is required for the temperature sensor area at a minimum. Insulation is
needed to ensure meeting our specified temperature measurement accuracy.
Insulation should only be placed up to the neck and not cover the transmitter.
00825-0100-4810_RevHA.fm Page 11 Friday, June 17, 2016 3:15 PM

June 2016
12
Quick Start Guide
Figure 10. Rosemount 405 Installation
A. Rosemount 405(1)
B. Alignment ring
C. Existing pipe assembly with flange
D. Nut
1. This installation drawing applies to the 405C, 405P, and 405A.
E. Gasket(2)
F. Stud
G. Transmitter(2)
2. The installation drawing applies when using the Rosemount 3051S, Rosemount 3051S
MultiVariable, Rosemount 3051, and Rosemount 2051 Transmitter. See the following documents
for quick installation instruction of the transmitter:
Rosemount 3051S MultiVariable Transmitter: document number 00825-0100-4803
Rosemount 3051S: document number 00825-0100-4801
Rosemount 3051: document number 00825-0100-4001
Rosemount 2051: document number 00825-0100-4101
A
B
G
A
F
C
D
B
E
00825-0100-4810_RevHA.fm Page 12 Friday, June 17, 2016 3:15 PM

Quick Start Guide
13
June 2016
4.0 Product certifications
4.1 Approved Manufacturing Locations
Rosemount Inc. – Chanhassen, Minnesota USA
Rosemount DP Flow Design and Operations – Boulder, Colorado USA
Emerson Process Management GmbH & Co. OHG – Wessling, Germany
Emerson Process Management Asia Pacific Private Limited – Singapore
Emerson Beijing Instrument Co., Ltd – Beijing, China
4.2 European Directive Information
The EC declaration of conformity for all applicable European directives for this
product can be found on the website at EmersonProcess.com/Rosemount. A
hard copy may be obtained by contacting our local sales office.
European Pressure Equipment Directive (PED) (97/23/EC)
Rosemount 405 Compact Primary Element — Sound Engineering Practice (SEP)
Pressure Transmitter — See appropriate Pressure Transmitter QSG.
4.3 Hazardous Locations Certifications
For information regarding the electronics product certification, see the
appropriate transmitter Quick Start Guide:
Rosemount 3051SMV: (document number 00825-0100-4803)
Rosemount 3051S: (document number 00825-0100-4801)
Rosemount 3051: (document number 00825-0100-4001)
Rosemount 2051: (document number 00825-0100-4101)
00825-0100-4810_RevHA.fm Page 13 Friday, June 17, 2016 3:15 PM

June 2016
14
Quick Start Guide
Figure 11. Rosemount 405 Declaration of Conformity
00825-0100-4810_RevHA.fm Page 14 Friday, June 17, 2016 3:15 PM

Quick Start Guide
15
June 2016
00825-0100-4810_RevHA.fm Page 15 Friday, June 17, 2016 3:15 PM

June 2016
16
Quick Start Guide
00825-0100-4810_RevHA.fm Page 16 Friday, June 17, 2016 3:15 PM

Quick Start Guide
17
June 2016
表表格
1B:
含有
China RoHS
管控物峐超彯㚨⣏㳻⹎旸ῤ的部件型号列表
Rosemount 405
Table 1B: List of Rosemount 405 Parts with China RoHS Concentration above MCVs
部件名称
Part Name
有害物峐ġİġHazardous Substances
摭
Lead
(Pb)
汞
Mercury
(Hg)
擱
Cadmium
(Cd)
六价撔
Hexavalent
Chromium
(Cr +6)
多
ⓤ
俼劗
Polybrominated
biphenyls
(PBB)
多
ⓤ
俼劗慂
Polybrominated
diphenyl ethers
多
ⓤ
俼劗慂
(PBDE)
䬍ࡦ⑙ᓖՐ
ᝏಘཆ༣㓴
Ԧ
Aluminum
RTD
Housing
Assembly
O O O X O O
本表格系依据
SJ/T11364
的奬⭂侴⇞ἄįġ
This table is proposed in accordance with the provision of SJ/T11364
O:
意󰶃宍悐ẞ䘬㇨㚱⛯峐㛸㕁󰵶宍㚱⭛䈑峐䘬⏓慷⛯ỶḶ
GB/T 26572
所奬⭂䘬旸慷天㯪įġ
O: Indicate that said hazardous substance in all of the homogeneous materials for this part is below the limit requirement of
GB/T 26572.
X:
意󰶃⛐宍悐ẞ㇨ἧ䓐䘬㇨㚱⛯峐㛸㕁慴炻军⮹㚱ᶨ䰣⛯峐㛸㕁󰵶宍㚱⭛䈑峐䘬⏓慷檀Ḷ
GB/T 26572
所奬⭂䘬旸慷天㯪įġ
X: Indicate that said hazardous substance contained in at least one of the homogeneous materials used for this part is above
the limit requirement of GB/T 26572.
к䘠⭣᰾ӵ䘲⭘Ҿ䘹ᤙ䬍ࡦཆ༣㓴ԦⲴӗ૱DŽަԆᡰᴹᐞ঻⍱䟿а⅑ݳԦⲴ㓴ԦᡰᴹⲴ China RoHS ㇑᧗⢙䍘⎃
ᓖ൷վҾ GB/T 26572 ᡰ㿴ᇊⲴ䲀䟿㾱≲DŽޣҾᐞ঻⍱䟿䇑䘱ಘ㓴ԦⲴ㇑᧗⢙䍘⎃ᓖⲴ⭣᰾ˈ䈧৲ⴻ䘱ಘⲴᘛ
䙏ᆹ㻵ᤷইDŽ
The disclosure above applies to units supplied with aluminum connection heads. No other components supplied
with DP Flow primary elements contain any restricted substances. Please consult the transmitter Quick Start
Guide (QIG) for disclosure information on transmitter components.
00825-0100-4810_RevHA.fm Page 17 Friday, June 17, 2016 3:15 PM

Global Headquarters
Emerson Process Management
6021 Innovation Blvd.
Shakopee, MN 55379, USA
[phone] or [phone]
[phone]
[email protected]
North America Regional Office
Emerson Process Management
8200 Market Blvd.
Chanhassen, MN 55317, USA
[phone] or [phone]
[phone]
[e-mail]
Latin America Regional Office
Emerson Process Management
1300 Concord Terrace, Suite 400
Sunrise, FL 33323, USA
[phone]
[phone]
[email protected]
Linkedin.com/company/Emerson-Process-Management
Twitter.com/Rosemount_News
Facebook.com/Rosemount
Youtube.com/user/RosemountMeasurement
Google.com/+RosemountMeasurement
Standard Terms and Conditions of Sale can be found at
www.Emerson.com/en-us/pages/Terms-of-Use.aspx
The Emerson logo is a trademark and service mark of Emerson
Electric Co.
Annubar, Rosemount and Rosemount logotype are trademarks of
Emerson Process Management.
All other marks are the property of their respective owners.
© 2016 Emerson Process Management. All rights reserved.
Europe Regional Office
Emerson Process Management Europe GmbH
Neuhofstrasse 19a P.O. Box 1046
CH 6340 Baar
Switzerland
[phone]
[phone]
[email protected]
Asia Pacific Regional Office
Emerson Process Management Asia Pacific Pte Ltd
1 Pandan Crescent
Singapore 128461
[phone]
[phone]
[e-mail]
Middle East and Africa Regional Office
Emerson Process Management
Emerson FZE P.O. Box 17033,
Jebel Ali Free Zone - South 2
Dubai, United Arab Emirates
[phone]
[phone]
[e-mail]
Quick Start Guide
00825-0100-4810, Rev HA
June 2016
*00825-0100-4810*
00825-0100-4810_RevHA.fm Page 18 Friday, June 17, 2016 3:15 PM