Emerson Lumity IC100D EVO User manual

QUICK REFERENCE GUIDE
IC100D EVO
(rel. 2.0)

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 3/40
INDEX
1GENERAL WARNING ...........................................................................................5
1.1 PLEASE READ BEFORE USING THIS MANUAL........................................................... 5
1.2 SAFETY PRECAUTIONS.................................................................................................. 5
1.3 PRODUCT DISPOSAL (WEEE) .................................................................................................6
2USING THE QUICK REFERENCE GUIDE..............................................................6
3ICHILL 105D / IC107D FEATURES........................................................................7
4USER INTERFACE................................................................................................8
4.1 MEANING OF THE LEDS........................................................................................................... 8
4.2 DISPLAY AND ICONS ................................................................................................................ 8
5DISPLAY LAYOUT..............................................................................................10
6OTHER DISPLAY INFORMATION.......................................................................10
6.1 READ THE SET POINT VALUE ............................................................................................... 10
6.2 MODIFY THE SET POINT ........................................................................................................ 11
7KEY FUNCTION..................................................................................................11
7.1 KEY COMBINANTION .............................................................................................................. 12
8FIRST INSTALLING ............................................................................................12
8.1 ON BOARD CLOCK (OPTIONAL)............................................................................................ 12
8.2 RTC SETUP............................................................................................................................... 12
9PARAMETERS PROGRAMMING WITH THE “HOT KEY 64”..............................13
9.1 HOW TO PROGRAM THE INSTRUMENT WITH AN ALREADY PROGRAMMED “HOT KEY”
(DOWNLOAD) .......................................................................................................................................... 13
9.2 HOW TO COPY THE PARAMETER MAP INTO THE “HOT KEY” (UPLOAD)...................... 13
10 PROGRAMMING USING LOCAL USER INTERFACE..........................................13
10.1 ENTER PARAMETERS PROGRAMMING LEVEL PR1.......................................................... 14
10.2 ENTER PARAMETERS PROGRAMMING LEVEL PR2.......................................................... 14
10.3 ENTER PARAMETERS PROGRAMMING LEVEL PR3.......................................................... 14
11 MENU ( MENU KEY)............................................................................................15
11.1 ALARM LIST: READ AND RESET ........................................................................................... 15
11.2 ALARM LOG LIST ..................................................................................................................... 16
12 REMOTE KEYBOARD VI613...............................................................................16
13 REMOTE LCD PANEL V2I810.............................................................................17
14 REMOTE TOUCH PANEL VTIC10.......................................................................17
15 TABLE OF THE OUTPUT STATUS IN ALARM CONDITION................................18
15.1 MACHINE ALARMS .................................................................................................................. 18
15.2 CIRCUIT ALARM....................................................................................................................... 20
15.3 COMPRESSOR ALARM ........................................................................................................... 21
15.1 WARNING.................................................................................................................................. 21
16 BLACK-OUT .......................................................................................................21
17 WIRING CONNECTIONS.....................................................................................22
17.1 IC105D MODEL: HARDWARE RESOURCES......................................................................... 22
17.2 IC107D MODEL: HARDWARE RESOURCES......................................................................... 23
17.1 REMOTE PANEL CONNECTION (VI613 EVO OR V2I810 OR VTIC10) ............................... 25
17.2 ANALOG INPUTS NTC –PTC PROBES................................................................................. 27
17.3 DIGITAL INPUTS....................................................................................................................... 28

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 4/40
17.4 ANALOG INPUT FOR PRESSURE TRANSDUCER PP30 (4 ÷ 20MA SIGNAL) ................... 28
17.5 ANALOG INPUT FOR PRESSURE RATIOMETRIC TRANSDUCER PPR30 (0 ÷ 5V SIGNAL)
29
17.6 PWM OUTPUT FOR CONDENSING FAN SPEED CONTROL .............................................. 30
17.7 PROPORTIONAL OUTPUT FOR FAN CONDENSING CONTROL OR FOR COMPRESSOR
INVERTER CONTROLLED OR FOR AUXILIARY OUTPUTS............................................................... 31
17.8 PROPORTIONAL OUTPUT 0..10V TO CONTROL DUMPER MOTORS............................... 32
17.9 PROPORTIONAL OUTPUTS CONFIGURED FOR AUX RELAY CONTROL........................ 34
17.10 CONNECTION TO THE IEV22D OR IEV12D ELECTRONIC EXPANSION VALVE DRIVER
35
18 INSTALLING AND MOUNTING ...........................................................................36
18.1 MECHANICAL CHARACTERISTIC.......................................................................................... 36
18.2 VERTICAL BOARDS VI613 PANEL CUT-OUT ....................................................................... 37
19 ELECTRICAL CONNECTIONS............................................................................38
20 TECHNICAL DATA..............................................................................................38
20.1 ELECTRICAL SPECIFICATIONS............................................................................................. 38
20.2 ANALOGUE INPUTS ................................................................................................................ 39
20.3 DIGITAL INPUT......................................................................................................................... 39
20.4 ANALOGUE OUTPUTS ............................................................................................................ 39
20.5 DIGITAL OUTPUTS................................................................................................................... 40

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 5/40
1 GENERAL WARNING
1.1 PLEASE READ BEFORE USING THIS MANUAL
•This manual is part of the product and should be kept near the instrument for easy and quick reference.
•The instrument shall not be used for purposes different from those described hereunder. It cannot be used
as a safety device.
•Check the application limits before proceeding.
•Dixell Srl reserves the right to change the composition of its products, even without notice, ensuring the
same and unchanged functionality.
1.2 SAFETY PRECAUTIONS
•Check the supply voltage is correct before connecting the instrument.
•Do not expose to water or moisture: use the controller only within the operating limits avoiding sudden
temperature changes with high atmospheric humidity to prevent formation of condensation
•Warning: disconnect all electrical connections before any kind of maintenance.
•The instrument must not be opened.
•In case of failure or faulty operation send the instrument back to the distributor or to “Dixell S.r.l.” with a
detailed description of the fault.
•Consider the maximum current which can be applied to each relay (see Technical Data).
•Ensure that the wires for probes, loads and the power supply are separated and far enough from each
other, without crossing or intertwining; do not use the same electrical conduit to install high voltage cabling
and low voltage cabling.
•The ground connection of the secondary coil of the transformer that powers the device can result in a bad
performance; where possible, this connection should be avoided.
•Fit the probe where it is not accessible by the end user.
•In case of applications in industrial environments, the use of mains filters (our mod. FT1) in parallel with
inductive loads could be useful.
•The symbol alerts the user of non-insulated “dangerous voltage” within the product area that is
sufficiently high to constitute a risk of electric shock to persons.
•The symbol alerts the user of important operating and maintenance (assistance) instructions
found in the documentation attached to the device.
➢Separate the power supply of the device from the rest of the electrical devices connected
inside the electrical panel.

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 6/40
➢The connection to ground of the secondary coil of the transformer that supply the device
may generate the malfunctionning of the device; where possible this connection must be
avoided.
1.3 PRODUCT DISPOSAL (WEEE)
With reference to Directive 2002/96/EC of the European Parliament and of the Council of 27 January
2003 and to the relative national legislation, please note that:
•There lies the obligation not to dispose of electrical and electronic waste as municipal waste
but to separate the waste.
•Public or private collection points must be used to dispose of the goods in accordance with
local laws. Furthermore, at the end of the product's life, it is also possible to return this to the
retailer when a new purchase is made.
•This equipment may contain hazardous substances. Improper use or incorrect disposal can
have adverse effects on human health and the environment.
•The symbol shown on the product or the package indicates that the product has been placed
on the market after 13 August 2005 and must be disposed of as separated waste.
•Should the product be disposed of incorrectly, sanctions may be applied as stipulated in
applicable local regulations regarding waste disposal.
2 USING THE QUICK REFERENCE GUIDE
In this guide, there are some general guidelines regarding the product; more details are in the full manual, to
be requested from the Dixell Customer Service department.

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 7/40
3 ICHILL 105D / IC107D FEATURES
FEATURES
IC105D
IC107D
RELAYS
5

7

DIGITAL INPUTS
9 (free voltage)
configurable
configurable
PROBES
4 (NTC or PTC or Digital Input)
configurable
configurable
3 (NTC or PTC or 0..5V or 4..20mA or Digital Input)
configurable
configurable
PROPORTIONAL OUTPUTS
2 (0÷10V or 4..20mA or PWM outputs)
configurable
configurable
1 (0÷10V)
configurable
configurable
OTHER OUTPUTS
TTL serial line (Modbus RTU protocol)


RS485 (Modbus RTU protocol)


Remote panel VI613 (up to 2 remote keyboards) or one V2I810 (LCD
panel) or one VT810 (Touch panel)


LAN (to connect IEV electronic expansion valve driver)


POWER SUPPLY
12 Vac/dc (+15%;-10%)


24 Vac/dc (± 10%)
opt
opt
OTHERS
Internal real time clock
opt
opt
Buzzer


▪configurable = the function assigned to the I/O is configurable by parameter
▪opt = optional
▪= default

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 8/40
4 USER INTERFACE
4.1 MEANING OF THE LEDS
4.2 DISPLAY AND ICONS
ICON
MEANING / FUNCTIONNING
°C
°F BAR
PSI
Lighted when the display shows a temperature or pressure
Lighted when the bottom display shows the clock
Lighted during the programming parameters if it is time based
Lighted in function menu when the display shows the defrost delay
Alarm: blinking in case of alarm
Lighted when sanitary hot water function is active

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 9/40
Lighted after pressing menu button
Lighted if anti freeze heaters/ integration heating / boiler are activated
Flow switch alarm / supply fan overload (air / air unit)
Water pump: lighted if at least one pump is ON
Condenser fan: lighted if at least one fan is ON
Lighted when a compressor is ON
Blinking = when the delay of activation is running
AUX
Lighted when auxiliary function is active
Lighted when the controller is ON in cooling or heating
FC
Lighted when the Free cooling is active
Lighted when the defrost is activated
Blinking when the delay to activate the defrost is active

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 10/40
5 DISPLAY LAYOUT
Pressing Up or Down button the display shows the temperature or pressure of the main probes configured in
the instrument.
The lower display shows the label of the selected probe while the upper display shows its value.
6 OTHER DISPLAY INFORMATION
6.1 READ THE SET POINT VALUE
Press and release the SET key:
If the unit is on standby:
•lower display shows SEtC (set chiller);
•press SET key again, lower display shows SEtH (set heat pump, if it is enabled);
•press SET key again, lower display shows SEtr (set real of operation, in the case where the Energy
Saving and / or function dynamic set point are active);
•press SET key again, lower display shows SEtS (set sanitary circuit, in case it is enabled)
If the instrument is in chiller operation:
•lower display shows SEtC (set chiller);
•press SET key again, lower display shows SEtr (set real of operation, in the case where the Energy
Saving and / or function dynamic set point are active);
•press SET key again, lower display shows SEtS (set sanitary circuit, in case it is enabled)
If the instrument is in chiller operation:
•lower display shows SetH (set heat pump);
•press SET key again, lower display shows SEtr (set real of operation, in the case where the Energy
Saving and / or function dynamic set point are active);
•press SET key again, lower display shows SEtS (set sanitary circuit, in case it is enabled)

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 11/40
6.2 MODIFY THE SET POINT
•push SET key for at least 3 seconds
•use the UP or DOWN key to modify the setpoint. In chiller mode it is possible to modify the chiller
set point, in heat pump it is possible to modify the heat pump set point, in std-by it is possible to
modify both the set point.
•push SET to confirm or wait the timeout (15seconds).
7 KEY FUNCTION
KEY
ACTION
FUNCTION
Push and release
Show chiller set point SetC, heat pump set point
SetH, sanitay water set point SetS
Push once again
In chiller or heat pump if the Energy saving or the
Dynamic setpoint are enabled it shows the real
setpoint Setr.
Push for 3 seconds
Allows to modify the set point
During the programming: push
once
To enter parameter modification or confirm a value
Push when an alarm is showed in
menù ALrM
To reset the alarm
Push once
To read probes value
Pushing once during the
programming
To change the group of parameters, to change the
parameter, to change the value of the parameter
Push for 1 second during the
programming when the display
visualizes Pr1 or Pr2 or Pr3
1 time shows the Pr2 programming level
2 times shows the Pr3 programming level
Push once
To read probes value
Pushing once during the
programming
To change the group of parameters, to change the
parameter, to change the value of the parameter
Push once
To turn ON or turn OFF the controller (in chiller or
heat pump depending from CF59 parameter)
Push once
To turn ON or turn OFF the controller (in chiller or
heat pump depending from CF59 parameter)
Push once
To enter the function Menu
Push for 3 seconds
To set the clock (only for controller with clock on
board)

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 12/40
Pushing once during the
programming
To exit from a group of parameters
7.1 KEY COMBINANTION
KEY
ACTION
FUNCTION
+
Push for 3 seconds together
Enter the programming parameters
Only in Pr3 level: push SET and
DOWN key
Select the parameter level visibility Pr1 / Pr2 / Pr3
+
Push once together
Exit the programming parameters
Push 5 seconds in heat pump
mode
Manual defrost
+
Only in Pr3 programming level:
push SET and then the MENU key
In Pr3 defines if the parameter can be modified or
not in the other levels.
8 FIRST INSTALLING
8.1 ON BOARD CLOCK (OPTIONAL)
In case of power failure the time and date are maintained for about 3 days (at room temperature 25 °C); the
display shows the message "rtC" and it is necessary to set the clock.
8.2 RTC SETUP
1. Push Menu key continuously for 3 seconds until the bottom display shows “Hour” and the top display
shows its value.
2. Push SET one time: the value is blinking.
3. Use the Up and Down keys to adjust it. Push SET one time to confirm.
4. Push up or down keys and repeat the operations 2. 3. and 4. for all the RTC parameters:
-Min: minutes (0÷60)
-UdAy: day of the week (Sun = Sunday, Mon =Monday, tuE =Tuesday, UEd = Wednesday, tHu =
Thursday, Fri =Friday, SAt =Saturday)
-dAy: day of the month (0÷31)
-MntH: month (1÷12)
-yEAr: year (00÷99)

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 13/40
9 PARAMETERS PROGRAMMING WITH THE “HOT KEY 64”
9.1 HOW TO PROGRAM THE INSTRUMENT WITH AN ALREADY
PROGRAMMED “HOT KEY” (DOWNLOAD)
1. Power off the instrument
2. Insert the hot key already programmed (by software Wizmate or other instrument)
3. Power on the instrument
4. Automatically the parameters are downloaded
During the download the regulation is locked and the top display shows the “doL” blinking label. At the end of
the download will appear:
•“End” if the programming procedure is completely OK, after 30seconds the regulation starts
automatically.
•“Err” if the programming procedure has found an error and the parameter have not been
transferred. In this case turn off and then on the instrument supply to repeat the operation or
remove the hot key, with power supply off, to restart the regulation.
9.2 HOW TO COPY THE PARAMETER MAP INTO THE “HOT KEY”
(UPLOAD)
1. Power on the instrument
2. Insert the hot key
3. Enter the function Menu
4. Select the UPL function (on the bottom display)
5. Push SET key and immediately the instrument starts transfer the parameters into the Hot key.
During the upload the regulation is locked and the top display shows the “UPL” blinking label. At the end of the
UPLOAD will appear:
1. “End” if the programming procedure is completely OK, after 30seconds the regulation starts
automatically.
2. “Err” if the programming procedure has found an error and the parameter have not been
transferred. Repeat the procedure.
To exit the UPL function push the MENU key or wait the time-out (15 sec).
10 PROGRAMMING USING LOCAL USER INTERFACE
Though the keyboard it is possible to modify the values of the parameters and set for each one of them the
visibility and editability; each parameter can be made visible at different levels of users:
1. Pr1 User level (default Password = 1)
2. Pr2 Maintenance level (default Password = 2)
3. Pr3 OEM level (default Password = 3)
The default password for resetting the alarm history and compressor overload alarm is 4.
Passwords can be customized using specific parameters; in the case in which it is necessary to access the
parameters and the passwords have been changed, it is necessary to contact the machine manufacturer to
obtain the necessary information.

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 14/40
10.1 ENTER PARAMETERS PROGRAMMING LEVEL PR1
Enter the Pr1 “User level”:
1. Push SET + DOWN keys together for 3 seconds. The top display shows “PAS”and the bottom display
shows “Pr1”.
2. Push SET key and the top display shows “0” blinking
3. Push UP or DOWN to select Pr1 password
4. Push SET and, if the value is correct, the top display shows the first family of parameters “ALL”
5. Push UP or DOWN to select the parameter family
6. Push SET to enter; the bottom display shows the first available parameter while the top display shows its
value.
7. Push UP or DOWN to modify its value
8. Push SET to confirm the new value
9. If necessary, modify others parameter
10. Push SET + UP keys together to exit parameters programming
10.2 ENTER PARAMETERS PROGRAMMING LEVEL PR2
Enter the Pr2 “service level”:
1. Push SET + DOWN keys together for 3 seconds. The top display shows “PAS”and the bottom display
shows “Pr1”
2. Push UP key for 2 seconds and the top display will show Pr2
3. Push SET key and the top display shows “0” blinking
4. Push UP or DOWN to select Pr2 password
5. Push SET and, if the value is correct, the top display shows the first family of parameters “ALL”
6. Push UP or DOWN to select the parameter family
7. Push SET to enter, the bottom display shows the first available parameter label while the top display
shows its value
8. Push UP or DOWN to modify its value
9. Push SET to confirm the new value
10. If necessary, modify others parameter
11. Push SET + UP keys together to exit parameters programming
10.3 ENTER PARAMETERS PROGRAMMING LEVEL PR3
Enter Pr3 “OEM level”:
1. Push SET + DOWN keys together for 3 seconds. The top display shows PAS and the bottom display
shows Pr1
2. Push UP key for 2 seconds and the top display shows Pr2
3. Push UP key again for 2 seconds and the top display will show Pr3
4. Push SET key and the top display shows “0” blinking
5. Push UP or DOWN to select Pr3 password
6. Push SET and, if the value is correct, the top display shows the first family of parameters “ALL”
7. Push UP or DOWN to select the parameter family
8. Push SET to enter; the bottom display shows the first available parameter label while the top display
shows its value
9. Push UP or DOWN to modify its value

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 15/40
10. Push SET to confirm the new value
11. If necessary, modify others parameter
12. Push SET + UP keys together to exit parameters programming
11 MENU ( MENU KEY)
Enter the menu:
• press the menu button;
• press the UP or DOWN button to select the submenu;
• press the SET to enter the submenu.
Exit menu functions:
• Press the menu button or wait the time-out.
Entering the menu, it is possbile to:
•ALrM Read and reset the alarms
•ALOG Read and reset the alarm log
•UPL Upload the parameter into the Hot Key
•CrEn Enable –disable one or the two circuits
•COEn Enable –disable one of the compressors
•Hour Read and reset the number of compressor running hour
•COSn Read and reset the number of compressor starts-up
•COdt Read the compressor discharge temperature
•Cond Read the condensing fan speed percentage of the proportional output
•Pout Read the percentage of the proportional output 0 ÷ 10 Vdc
•PoEn Enable –disable evaporator or condenser water pumps
•dF Time counting to next defrost cycle, under heat pump mode,
•uS Read the probe temperatures that enabled to control the auxiliary output
•SoL Read temperature, Set point and output status of solar panel
•FC Read temperature, Set point and output status of Free cooling
•trEM Read probe temperature of the remote panels
•Et1 Read temperature, pressure, set point of the electronic expansion valve 1
•Et2 Read temperature, pressure, set point of the electronic expansion valve 2
•REC Enable / disable recovery function
11.1 ALARM LIST: READ AND RESET
ALrM FUNCTION
1. Push MENU key
2. The display shows AlrM label
3. Push SET key (Nothing happens if there are not alarms)
4. The bottom display shows the alarm code and the top display shows the label rSt, if it is possible to reset
the alarm, or NO if it is not possible to reset the alarm
5. Push UP or DOWN to scroll the alarm list (if more than one alarm is active)
6. Repeat the reset procedure for each alarm

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 16/40
7. To exit the ALrM reset, push MENU or wait the timeout.
11.2 ALARM LOG LIST
ALOG FUNCTION
1. Push MENU key
2. Push UP or DOWN to select ALOG
3. Push SET key
4. The bottom display shows the alarm label, the top display shows a number in the range 00 to 99.
5. Use the UP or DOWN keys to scroll the list.
6. To exit the ALOG function push MENU or wait the timeout.
Erase the Alarm log list
1. Push MENU key
2. Push UP or DOWN to select ALOG
3. Push the SET key
4. Push UP or DOWN keys and search the ArSt label on the bottom display; the top display shows PAS.
5. Push SET; the bottom display shows PAS and the top display shows “0”blinking
6. Push UP or DOWN to set the password
7. If the password is OK the label ArST blinks for 5 seconds then the display returns to normal condition
read-out
8. If the password is not correct the display shows PAS again
9. To exit, push the MENU key or wait the timeout.
The standard password to reset the alarm log is “4”.
12 REMOTE KEYBOARD VI613
The display visualization and the button functions are the same of the Ichill, then refer to previous chapters of
the quick reference guide.

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 17/40
13 REMOTE LCD PANEL V2I810
The description of the user interface is available in the user manual of the Visograph.
14 REMOTE TOUCH PANEL VTIC10
The description of the user interface is available in the user manual of the Visotouch.

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 18/40
15 TABLE OF THE OUTPUT STATUS IN ALARM CONDITION
15.1 MACHINE ALARMS
Alarm
Code
Alarm
description
Comp.
Heaters
Support
heaters
(air/air
unit)
Evaporator
Pump /
Supply fan
Condenser
Pump
Domestic
hot water
Water
pump
Solar
panel
Water
pump
Condenser
fan
Auxiliary
relay
ACF1
...
AC16
Configuration
alarm
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ACFL
Condenser
flow alarm
OFF
(4)
(8)
(8)
(8)
OFF (3)
(8)
(8)
(8)
(8)
AEE
Eeprom alarm
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
AEFL
Evaporator
flow alarm
OFF
(4)
OFF
(boiler)
(8)
OFF (3)
(8)
(8)
(8)
(8)
(8)
AEht
High inlet
evaporator
water
temperature
OFF
OFF
(boiler)
(8)
(8)
(8)
(8)
(8)
(8)
(8)
AHFL
Domestic hot
water flow
switch alarm
OFF
(6)
(8)
(8)
(8)
OFF
OFF
(8)
(8)
(8)
ALC1
General alarm
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ALC2
General alarm
type 2
OFF
(9)
OFF (9)
OFF (9)
OFF (9)
OFF (9)
OFF (9)
OFF
(9)
OFF (9)
OFF (9)
ALSF
Phase
sequence
alarm
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ALti
Low air
temperature of
the evaporator
inlet (air / air
unit) Alarm
AP1
...
AP6
Probe alarm
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
APE1
...
APE8
I/O Expansion
probe alarm
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
APFL
Solar panel
flow switch
alarm
OFF
(6)
(8)
(8)
(8)
(8)
(8)
OFF
(8)
(8)
APr1
APr2
Remote
keyboard
probe alarm
OFF
(3)
OFF (3)
OFF (3)
OFF (3)
OFF (3)
OFF (3)
OFF
(3)
OFF (3)
OFF (3)

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 19/40
APU1
...
APU4
IEV Electronic
Expansion
Valve probe
alarm
(7)
(7)
(7)
(7)
(7)
(7)
(7)
(7)
ASLA
Serial
communication
failure with I/O
expansion
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
AtAS
Domestic hot
water pump
overload
OFF
(6)
(8)
(8)
(8)
(8)
(8)
(8)
AtC1
Condenser 1
water pump
overload alarm
OFF
(4)
(8)
(8)
(8)
OFF
(8)
(8)
OFF
(8)
AtC2
Condenser 2
water pump
overload alarm
OFF
(4)
(8)
(8)
(8)
OFF
(8)
(8)
OFF
(8)
AtE1
Evaporator 1
water pump
overload alarm
OFF
(4)
OFF
(boiler)
(5)
(8)
OFF
(8)
(8)
(8)
OFF
(8)
AtE2
Evaporator 2
water pump
overload alarm
OFF
(4)
OFF
(boiler)
(5)
(8)
OFF
(8)
(8)
(8)
OFF
(8)
AtHS
Domestic hot
water heaters
overload
(8)
AtSF
Fan supply
overload alarm
OFF
OFF
OFF
(8)
(8)
AUAL
Serial
communication
failure with
IEV expansion
valve driver
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
AtrE
Remote
terminal
Visograph 2.0
communication
alarm
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
Atr1
Atr2
Remote
terminal VI613
communication
alarm
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1) = the status of the load depends on wich probe is faulty; e.g. if the regulation probe is faulty main loads
are OFF, if external temperature probe is faulty there is not direct actions on the loads but the dynamic
set point function is disabled
(2) = with probe configured as auxiliary relay control
(3) = loads are OFF only if the probe of the remote keyboard is set as regulation probe
(4) = The compressors are Off if the water pump is the only configured water pump; if 2 water pumps are
configured, the compressors are OFF if both water pumps are in alarm or not available

1592022020 iCHILL 100D EVO QRG EN rel. 2.0 23.02.2022 20/40
(5) = Boiler heaters off if the water pump is the only configured water pump; if 2 water pumps are configured,
the compressors are OFF if both water pumps are in alarm or not available
(6) Compressors switched off if only production of domestic hot water is ongoing
(7) In case of electronic expansion valve alarm all loads are OFF
(8) This loads are not influenced directly by the alarm; their status depends on the configuration of the device
(9) If A050=0 it is only a warning and the loads are not involved, if A050=1 it is a real alarm and the loads are
switched OFF
15.2 CIRCUIT ALARM
Alarm
Code
Alarm description
Compressors
Fan condensing
b1AC
Anti-freeze alarm in chiller mode
OFF
OFF
b1Ac
Anti-freeze warning in chiller
b1AH
Anti-freeze alarm in heat pump
OFF
OFF
b1Ah
Anti-freeze warning in heat pump
b1dF
End defrost alarm
b1HP
High pressure switch
OFF
OFF after 60
seconds
b1hP
High condenser pressure by pressure transducer
OFF
OFF after 60
seconds
b1hP
High condensing temperature
OFF
OFF after 60
seconds
b1LP
Low pressure switch
OFF
OFF
b1LP
Low pressure detected by evaporating pressure transducer or by high
pressure transducer (if only one pressure transducer is configured)
OFF
OFF
b1lP
Low condenser temperature
OFF
OFF
b1PH
Pump down alarm during the switching off the compressor
OFF
OFF
b1PL
Pump down during the switching on the compressor
OFF
OFF
b1tF
Fan overload
OFF
OFF
b1UA
Expansion valve 1 or valve 2 alarm
OFF
OFF