Emerson Rosemount 2410 User manual

Manual Supplement
00809-0200-2410, Rev AB
January 2022
Rosemount™ 2410 Tank Hub
Upgrade Instruction for Primary Bus and Secondary Bus

Safety messages
WARNING
Failure to follow these installation guidelines could result in death or serious injury.
•Ensure only qualified personnel perform the installation.
•Use the equipment only as specified in this manual. Failure to do so may impair the protection provided by the equipment.
Explosions could result in death or serious injury.
•Verify that the operating environment of the device is consistent with the appropriate hazardous locations certifications.
•To prevent ignition of flammable or combustible atmospheres, disconnect power before servicing.
Electrical shock could cause death or serious injury.
•Use extreme caution when making contact with the leads and terminals.
•Ensure the mains power to the device is off and the lines to any other external power source are disconnected or not powered
while wiring the device.
WARNING
Any substitution of non-recognized parts may jeopardize safety. Repair (e.g. substitution of components) may also jeopardize
safety and is not allowed under any circumstances.Unauthorized changes to the product are strictly prohibited as they may
unintentionally and unpredictably alter performance and jeopardize safety. Unauthorized changes that interfere with the integrity
of the welds or flanges, such as making additional perforations, compromise product integrity and safety. Equipment ratings and
certifications are no longer valid on any products that have been damaged or modified without the prior written permission of
Emerson. Any continued use of product that has been damaged or modified without the written authorization is at the customer’s
sole risk and expense.
2

Contents
Chapter 1 Introduction.............................................................................................................. 5
Chapter 2 The upgrade kit..........................................................................................................7
Chapter 3 Installation procedure................................................................................................9
Chapter 4 Upgrade procedure.................................................................................................. 11
Manual Supplement Contents
00809-0200-2410 January 2022
Rosemount 2410 Tank Hub 3

Contents Manual Supplement
January 2022 00809-0200-2410
4 Emerson.com/Rosemount

1 Introduction
This instruction describes how to upgrade a Primary/Secondary Fieldbus on existing
Rosemount 2410 Tank Hub.
Note
The upgrade must be documented. This includes stating the serial number of the device,
date of upgrade, type of upgrade and name of the person performing the upgrade.
Manual Supplement Introduction
00809-0200-2410 January 2022
Rosemount 2410 Tank Hub 5

Introduction Manual Supplement
January 2022 00809-0200-2410
6 Emerson.com/Rosemount

2 The upgrade kit
The modification kit consists of the following parts:
•Screw M3x6
•Plate for Main Label
•Main and Spare Part Label
•PCM Modem Board (if applicable)
•Start Code (if applicable)
Manual Supplement The upgrade kit
00809-0200-2410 January 2022
Rosemount 2410 Tank Hub 7

The upgrade kit Manual Supplement
January 2022 00809-0200-2410
8 Emerson.com/Rosemount

3 Installation procedure
When upgrading the 2410 Tank Hub, make sure to follow and observe local safety
regulations when working with electrical equipment within the hazardous locations.
Always make sure to have the necessary site permissions before starting any kind of work
within the hazardous locations. If unsure, consult the local personnel on site.
Manual Supplement Installation procedure
00809-0200-2410 January 2022
Rosemount 2410 Tank Hub 9

Installation procedure Manual Supplement
January 2022 00809-0200-2410
10 Emerson.com/Rosemount

4 Upgrade procedure
Procedure
1. Power off the device at the power source.
2. Disconnect all cabling.
3. If necessary, move the device head to a safe, non-hazardous area.
WARNING
Bring the transmitter head to a suitable location for maintenance work and
continue with the exchange and make sure to follow proper protection procedures
in order to avoid damage from Electrostatic Discharge (ESD).
4. Remove the cover from the transmitter.
5. Unsnap the display cover by pressing two plastic clips upwards.
Manual Supplement Upgrade procedure
00809-0200-2410 January 2022
Rosemount 2410 Tank Hub 11

6. Disconnect the cables from the mother board.
7. Remove all the 6 screws holding the plastic holder inside the housing.
8. Remove the plastic holder from the housing.
Upgrade procedure Manual Supplement
January 2022 00809-0200-2410
12 Emerson.com/Rosemount

9. Press down the plastic clips to detach the electronics. Detach and remove the
electronics package from the plastic holder.
10. Remove the plate that holds the power supply in place. This will allow for easy
access to the primary and secondary bus boards.
Manual Supplement Upgrade procedure
00809-0200-2410 January 2022
Rosemount 2410 Tank Hub 13

11. Exchange the primary or secondary bus board depending on the desired
configuration. Add or exchange the primary/secondary board depending on desired
configuration.
A. Primary bus
B. Secondary bus
12. If an IS board is mounted on the primary side make sure the connection cable is
placed under the secondary bus board if such board is present.
Upgrade procedure Manual Supplement
January 2022 00809-0200-2410
14 Emerson.com/Rosemount

13. Attach the power supply board back to the main board, ensure that all boards are
aligned and properly resting against the board support.
14. Steer the boards into the grooves of the holder; make sure the heat sink is properly
aligned against the bottom of the holder.
Manual Supplement Upgrade procedure
00809-0200-2410 January 2022
Rosemount 2410 Tank Hub 15

15. Push the two parts together all the way until the holder snaps in place and the
boards are visible in the inspection holes.
16. Place the electronic package back into the housing and secure it with the screws.
17. Connect all the cables back to the mother board where applicable.
Upgrade procedure Manual Supplement
January 2022 00809-0200-2410
16 Emerson.com/Rosemount

18. Make sure that cables are not pushed down in the space next to the IS Component
(if present), the cabling might otherwise impair Intrinsic Safety of the Board.
19. Arrange the cables so that they can't be damaged by the threads when mounting
the housing cover.
20. Snap on the Display cover or the Label Display Cover (depending on the version).
21. Inspect the O-ring on the housing cover, make sure it is not damaged, and if it is dry
apply some grease on the O-ring and the threads. Damaged O-ring must be
replaced with a new one.
22. Tighten the cover.
23. Remove the old label plate and replace it with the new one.
24. Apply the new main label on the plate.
25. Connect the device and power it on, if a display is present make sure the device is
working properly. When there is no display present contact the control room and
verify that the device is back on-line.
Manual Supplement Upgrade procedure
00809-0200-2410 January 2022
Rosemount 2410 Tank Hub 17

26. If a start code is included with the upgrade it must be entered before full
functionality can be achieved.
27. Start WinSetup board, find the upgraded 2410 Device, right click on it and select
properties. Under Advanced tab select on Upgrade Device button.
28. Enter the Start Code as specified in the information provided with the upgrade.
Select OK and Apply to close the properties window.
29. Your 2410 device is now upgraded. You may need to make additional configuration
adjustments based on type of upgrade. See the Rosemount 2410 Tank Hub
Reference Manual for more details.
Upgrade procedure Manual Supplement
January 2022 00809-0200-2410
18 Emerson.com/Rosemount

Manual Supplement
00809-0200-2410 January 2022
Rosemount 2410 Tank Hub 19

00809-0200-2410
Rev. AB
2022
For more information: www.emerson.com
©2022 Emerson. All rights reserved.
Emerson Terms and Conditions of Sale are available upon
request. The Emerson logo is a trademark and service mark of
Emerson Electric Co. Rosemount is a mark of one of the
Emerson family of companies. All other marks are the property
of their respective owners.