Emerson Rosemount 3051S Series User manual

www.rosemount.com
Reference Manual
00809-0100-4802, Rev BA
August 2007
Rosemount 3051S Wireless Series Scalable
Pressure, Flow, and Level Solutions

Reference Manual
00809-0100-4802, Rev BA
August 2007 Rosemount 3051S Wireless Series
www.rosemount.com
Rosemount 3051S Wireless Series Scalable
Pressure, Flow, and Level Solutions
NOTICE
Read this manual before working with the product. For personal and system safety, and
for optimum product performance, make sure you thoroughly understand the contents
before installing, using, or maintaining this product.
For technical assistance, contacts are listed below:
Customer Central
Technical support, quoting, and order-related questions.
United States - 1-800-999-9307 (7:00 am to 7:00 pm CST)
Asia Pacific- 65 777 8211
Europe/ Middle East/ Africa - 49 (8153) 9390
North American Response Center
Equipment service needs.
1-800-654-7768 (24 hours—includes Canada)
Outside of these areas, contact your local Rosemount®representative.
The products described in this document are NOT designed for nuclear-qualified
applications. Using non-nuclear qualified products in applications that require
nuclear-qualified hardware or products may cause inaccurate readings.
For information on Rosemount nuclear-qualified products, contact your local Rosemount
Sales Representative.
Failure to follow these installation guidelines could result in death or serious injury:
• Make sure only qualified personnel perform the installation.
Explosions could result in death or serious injury:
Installation of this transmitter in an explosive environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Please
review the approvals section of this manual for any restrictions associated with a safe
installation.
• Before connecting a 375 Field Communicator in an explosive atmosphere, ensure the
instruments are installed in accordance with intrinsically safe or non-incendive field
wiring practices.
• Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications.
Process leaks could result in death or serious injury.
• Install and tighten process connectors before applying pressure.
• Do not attempt to loosen or remove process connectors while the transmitter is in
service.
Electrical shock can result in death or serious injury.
• Avoid contact with the leads and terminals. High voltage that may be present on leads
can cause electrical shock.

Reference Manual
00809-0100-4802, Rev BA
August 2007
Rosemount 3051S Wireless Series
tp-2
The battery pack with the wireless unit contains two “C” size primary
lithium/thionyl chloride batteries. Each battery contains approximately 2.5
grams of lithium, for a total of 5 grams in each pack. Under normal conditions,
the battery materials are self-contained and are not reactive as long as the
batteries and the pack integrity are maintained. Care should be taken to
prevent thermal, electrical or mechanical damage. Contacts should be
protected to prevent premature discharge.
Battery hazards remain when cells are discharged.
Batteries should be stored in a clean and dry area. For maximum battery life,
storage temperature should not exceed 30° C.
NOTICE
The Rosemount 3051S and all other wireless devices should be installed only after the
1420 Wireless Gateway has been installed and is functioning properly. Wireless devices
should also be powered up in order of proximity from the 1420 Wireless Gateway,
beginning with the closest. This will result in a simpler and faster network installation.
NOTICE
Shipping considerations for wireless products (Lithium Batteries):
The unit was shipped to you without the battery installed. Please remove the battery pack
from the unit prior to shipping.
Primary lithium batteries are regulated in transportation by the U. S. Department of
Transportation, and are also covered by IATA (International Air Transport Association),
ICAO (International Civil Aviation Organization), and ARD (European Ground
Transportation of Dangerous Goods). It is the responsibility of the shipper to ensure
compliance with these or any other local requirements. Please consult current regulations
and requirements before shipping.

Reference Manual
00809-0100-4802, Rev BA
August 2007 Rosemount 3051S Wireless Series
1-1
SECTION 1
Introduction
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Models Covered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Service Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Shipping considerations for wireless products (Lithium Batteries): . . . . . .1-3
SECTION 2
Configuration
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Commissioning on the bench With HART . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Connection Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Review Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Field Communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Fast Key Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
Check Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
Process Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
Sensor Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
Basic Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
Set Process Variable Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
Set Output (Transfer function) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
Security (Write Protect) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7
LCD Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7
Detailed Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
Sensor Temperature Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
Diagnostics and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
Master Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
Advanced Functions for HART Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10
Saving, Recalling, and Cloning Configuration Data . . . . . . . . . . . . . . . . .2-10
Device Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
Transmit Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
Remove Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
Table of Contents

Reference Manual
00809-0100-4802, Rev BA
August 2007
Rosemount 3051S Wireless Series
1-2
SECTION 3
Installation
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Mount the Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Process Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
Consider Housing Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11
Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12
Installing the LCD Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12
Rosemount 304, 305 and 306 Integral Manifolds . . . . . . . . . . . . . . . . . . . . . .3-13
Rosemount 305 Integral Manifold Installation Procedure . . . . . . . . . . . .3-13
Rosemount 306 Integral Manifold Installation Procedure . . . . . . . . . . . .3-14
Rosemount 304 Conventional Manifold Installation Procedure . . . . . . . .3-15
Manifold Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
SECTION 4
Commissioning
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Network Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Verify Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
SECTION 5
Operation and
Maintenance
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
Sensor Trim Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Zero Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3
Sensor Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3
Recall Factory Trim—Sensor Trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4
Compensating for Line Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4
LCD Screen Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Startup Screen Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Diagnostic Button Screen Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7
Network Diagnostic Status Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
Device Diagnostic Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10
SECTION 6
Troubleshooting
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Disassembly Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
Remove from Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
Remove Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
Remove Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4
Remove the SuperModule from the Housing . . . . . . . . . . . . . . . . . . . . . . .6-4
Reassembly Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
Attach the SuperModule to the Wireless Housing . . . . . . . . . . . . . . . . . . .6-5
Install the Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
Reassemble the Process Flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5

Reference Manual
00809-0100-4802, Rev BA
August 2007 Rosemount 3051S Wireless Series
1-3
APPENDIX A
Specifications and
Reference Data
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Functional Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7
Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-10
Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-12
Rosemount 3051S Series Coplanar . . . . . . . . . . . . . . . . . . . . . . . . . . . A-12
Rosemount 3051S Series In-Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-17
Rosemount 3051S Series Liquid Level . . . . . . . . . . . . . . . . . . . . . . . . . A-20
Seal Options (page A-21—A-22) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-21
Transmitter Options continued from page A-20 . . . . . . . . . . . . . . . . . . . A-22
APPENDIX B
Product
Certifications
Wireless Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Approved Manufacturing Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Telecommunication Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Ordinary Location Certification for FM . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Hazardous Locations Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
European Directive Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
European Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2

Reference Manual
00809-0100-4802, Rev BA
August 2007
Rosemount 3051S Wireless Series
1-4

Reference Manual
00809-0100-4802, Rev BA
August 2007 Rosemount 3051S Wireless Series
www.rosemount.com
Section 1 Introduction
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-1
Models Covered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-2
Service Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-3
USING THIS MANUAL The sections in this manual provide information on installing, operating, and
maintaining the Rosemount 3051S Wireless pressure transmitter with HART®
protocol. The sections are organized as follows:
• Section 2: Configuration provides instruction on commissioning and
operating 3051S Wireless transmitters. Information on software
functions, configuration parameters, and online variables is also
included.
•Section 3: Installation contains mechanical and electrical installation
instructions.
• Section 4: Commissioning contains techniques for properly
commissioning the device.
•Section 5: Operation and Maintenance contains operation and
maintenance techniques.
•Section 6: Troubleshooting provides troubleshooting techniques for
the most common operating problems.
•Appendix A: Specifications and Reference Data supplies reference
and specification data, as well as ordering information.
•Appendix B: Product Certifications contains approval information.

Reference Manual
00809-0100-4802, Rev BA
August 2007
Rosemount 3051S Wireless Series
1-2
MODELS COVERED The following 3051S Wireless pressure transmitters are covered in this
manual.
Rosemount 3051S Wireless Coplanar™Pressure Transmitter
Rosemount 3051S Wireless In-Line Pressure Transmitter
Rosemount 3051S Wireless Liquid Level Pressure Transmitter
Performance
Class
Measurement Type
Differential Gage Absolute
Classic X X X
Performance
Class
Measurement Type
Differential Gage Absolute
Classic – X X
Performance
Class
Measurement Type
Differential Gage Absolute
Classic X X X

Reference Manual
00809-0100-4802, Rev BA
August 2007
1-3
Rosemount 3051S Wireless Series
SERVICE SUPPORT To expedite the return process outside of the United States, contact the
nearest Rosemount representative.
Within the United States, call the Emerson Process Management Instrument
and Valves Response Center using the 1-800-654-RSMT (7768) toll-free
number. This center, available 24 hours a day, will assist you with any needed
information or materials.
The center will ask for product model and serial numbers, and will provide a
Return Material Authorization (RMA) number. The center will also ask for the
process material to which the product was last exposed.
The battery pack with the wireless unit contains two “C” size primary
lithium/thionyl chloride batteries. Each battery contains approximately 2.5
grams of lithium, for a total of 5 grams in each pack. Under normal conditions,
the battery materials are self-contained and are not reactive as long as the
batteries and the pack integrity are maintained. Care should be taken to
prevent thermal, electrical or mechanical damage. Contacts should be
protected to prevent premature discharge.
Emerson Process Management Instrument and Valves Response Center
representatives will explain the additional information and procedures
necessary to return goods exposed to hazardous substances.
Individuals who handle products exposed to a hazardous substance can avoid injury if they
are informed of and understand the hazard. If the product being returned was exposed to a
hazardous substance as defined by OSHA, a copy of the required Material Safety Data
Sheet (MSDS) for each hazardous substance identified must be included with the returned
goods.
NOTICE
Shipping considerations for wireless products (Lithium Batteries):
The unit was shipped to you without the battery installed. Please remove the battery pack from
the unit prior to shipping.
Primary lithium batteries (charged or discharged) are regulated in transportation by the U. S.
Department of Transportation, and are also covered by IATA (International Air Transport
Association), ICAO (International Civil Aviation Organization), and ARD (European Ground
Transportation of Dangerous Goods). It is the responsibility of the shipper to ensure
compliance with these or any other local requirements. Please consult current regulations and
requirements before shipping.

Reference Manual
00809-0100-4802, Rev BA
August 2007
Rosemount 3051S Wireless Series
1-4

Reference Manual
00809-0100-4802, Rev BA
August 2007 Rosemount 3051S Wireless Series
www.rosemount.com
Section 2 Configuration
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-1
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-1
Commissioning on the bench With HART . . . . . . . . . . . . page 2-2
Review Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . page 2-3
Field Communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-4
Check Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-5
Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-6
LCD Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-7
Detailed Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-9
Diagnostics and Service . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-10
Advanced Functions for HART Protocol . . . . . . . . . . . . . page 2-11
Device Network Configuration . . . . . . . . . . . . . . . . . . . . . page 2-12
OVERVIEW This section contains information on commissioning and tasks that should be
performed on the bench prior to installation.
Field Communicator and AMS instructions are given to perform configuration
functions. For convenience, Field Communicator fast key sequences are
labeled “Fast Keys” for each software function below the appropriate
headings.
Example Software Function
SAFETY MESSAGES Procedures and instructions in this section may require special precautions to
ensure the safety of the personnel performing the operations. Information that
raises potential safety issues is indicated by a warning symbol ( ). Refer to
the following safety messages before performing an operation preceded by
this symbol.
Warnings ( )
Fast Keys 1, 2, 3, etc.
Explosions can result in death or serious injury.
• Before connecting a 375 Field Communicator in an explosive atmosphere, make
sure the instruments are installed in accordance with intrinsically safe or
nonincendive field wiring practices.
Electrical shock can result in death or serious injury.
• Avoid contact with the leads and terminals. High voltage that may be present on
leads can cause electrical shock.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following conditions: This device may not cause harmful interference this device
must accept any interference received, including interference that may cause
undesired operation.
This device must be installed to ensure a minimum antenna separation distance of
20cm from all persons.

Reference Manual
00809-0100-4802, Rev BA
August 2007
Rosemount 3051S Wireless Series
2-2
COMMISSIONING ON
THE BENCH WITH HART
Commissioning consists of testing the transmitter and verifying transmitter
configuration data. 3051S Wireless transmitters can be commissioned either
before or after installation. Commissioning the transmitter on the bench before
installation using a 375 Field Communicator or AMS ensures that all
transmitter components are in working order.
To commission on the bench requires a 375 Field Communicator or AMS.
Connect the Field Communicator leads to the terminals labeled “COMM” on
the terminal block. See Figure 2-1 on page 2-2.
When using a Field Communicator, any configuration changes made must be
sent to the transmitter by using the “Send” key (F2). AMS configuration
changes are implemented when the “Apply” button is clicked.
AMS Wireless and Direct Connections
AMS is capable of connecting to devices either directly, using a HART
modem, or wirelessly via the 1420. When configuring on the bench using a
HART modem, double click the device icon (or right click and select
Configure/Setup), then choose the Configure/Setup tab. Configure the device
settings using the Direct Connection menu. When configuring wirelessly via
the 1420, double click the device icon (or right click and select
Configure/Setup), then choose the Configure/Setup tab. Configure the device
settings using the Wireless Connection menu.
Connection Diagrams Bench Hook-up
Connect the bench equipment as shown in Figures 2-1, and turn on the Field
Communicator by pressing the ON/OFF key or log into AMS. The Field
Communicator or AMS will search for a HART-compatible device and indicate
when the connection is made. If the Field Communicator or AMS fail to
connect, it indicates that no device was found. If this occurs, refer to
Section 6: Troubleshooting.
Field Hook-up
Figures 2-1 illustrates the wiring for a field hook-up with a Field Communicator
or AMS. The Field Communicator or AMS may be connected at “COMM” on
the transmitter terminal block.
Figure 2-1. 375 Connection
For HART communication, a 3051S WPT DD is required.
COMM
P/N 00753-9200-0010
COMMCOMM
P/N00753-9200-0010P/N00753-9200-0010

Reference Manual
00809-0100-4802, Rev BA
August 2007
2-3
Rosemount 3051S Wireless Series
REVIEW
CONFIGURATION DATA
NOTE
Information and procedures in this section that make use of Field
Communicator fast key sequences and AMS assume that the transmitter and
communication equipment are connected, powered, and operating correctly.
The following is a list of factory default configurations. These can be reviewed
by using the Field Communicator or AMS.
Field Communicator
Enter the fast key sequence to view the configuration data.
AMS
Right click on the device and select “Configure/Setup” from the menu. Select
the tabs to review the transmitter configuration data.
Fast Keys 1, 5
Manufacturer Process Connector
Model Process Conn. Material
Measurement O Ring Material
Module Configuration Drain Vent Material
Module Range Number
Calibration Type Type
Model Number I Diaphragm Material
Model Number II Seal Fill Fluid
Model Number III Tag
PV is Date
SV is Descriptor
TV is Message
QV is Write Protect
Unit Power Mode
Lower Sensor Limit LCD Mode
Upper Sensor Limit Transmit Rate
Lower Range Point (0%) Universal Rev
Upper Range Point (100%) Field Device Rev
Min Span Software Rev
Lower Trim Point Hardware Rev
Upper Trim Point Radio Model Number
Supported Trim Radio Hardware Rev
Sensor 1 Trim Units Radio SW Major Rev
Min Lower Trim Radio SW Minor Rev
Max Lower Trim Radio SW Build
Min Upper Trim Physical Signaling
Max Upper Trim Transmitter S/N
Sensor 1 Min Trim Diff Dev ID
Transfer Function Network ID
Damping Node ID
Sensor S/N Radio Type
Unit Database Mode
Lower Sensor Limit Wireless Device Type
Upper Sensor Limit Poll Address
Unit Num Req Preams
Lower Sensor Limit Dev Flags
Upper Sensor Limit Distributor
Supply Units HI-HI Alert
Lower Sensor Limit HI Alert
Upper Sensor Limit LO Alert
Isolator Material LO-LO Alert
Fill Fluid

Reference Manual
00809-0100-4802, Rev BA
August 2007
Rosemount 3051S Wireless Series
2-4
FIELD COMMUNICATOR
Menu Tree
1. Universal
Rev.
2. Field
Device Rev.
3. Software
Rev.
4. Hardware
Rev.
1. Tag
2. Date
3. Descriptor
4. Message
5. Model
6. Model Number I
7. Model Number II
8. Model Number III
9. Write Protect
10. REVISION #’S
11. Final Assembly #
12. Device ID
13. Distributor
1. Measurement Type
2. Module Config Type
3. Isolator Material
4. Fill fluid
5. Process Connector
6. Process Connection
Material
7. O-Ring Material
8. Drain Vent Material
9. Module Range
10. Sensor Serial
Number
1. Pressure
2. Percent of Range
3. Sensor Temperature
4. Supply Voltage
5. Process Variable is
1. PRESSURE SENSOR
2. DEVICE TEMP. SENSOR
1. Date
2. Descriptor
3. Message
4. Write Protect
5. Model
6. Model Number I
7. Model Number II
8. Model Number III
1. Pressure
2. Percent of Range
3. Sensor Temperature
4. Supply Voltage
5. Process Variable is
1. Tag
2. Unit
3. RANGE VALUES
4. DEVICE INFO
5. Transfer Function
6. Damping
7. LCD Display Config.
1. Master Reset
2. Status
3. Status Log
1. Keypad Input
2. Apply Values
1. Keypad Input
2. Apply Values
1. Keypad Input
2. Apply Values
1. Poll Address
2. Num Req Preams
1. NETWORK
2. FIELD
DEVICE INFO
3. SENSOR
INFO
4. DIAPHRAGM
SEALS INFO
1. DEVICE SETUP
2. PV
3. Lower Range
Point (0%)
4. Upper Range
Point (100%)
1. PROCESS
VARIABLES
2. DIAG/SERVICE
3. BASIC SETUP
4. DETAILED
SETUP
5. Review
1. TEST DEVICE
2. CALIBRATION
1. RERANGE
2. SENSOR TRIM
3. Recall Factory Trim
Online Menu
1. PROCESS
VARIABLES
2. SENSOR
SERVICE
3. Unit
4. Damping
1. SENSORS
2. SIGNAL
CONDITION
3. OUTPUT
CONDITION
4. DEVICE
INFORMATION
1. PROCESS
VARIABLES
2. RANGE VALUES
3. Unit
4. Transfer Function
5. Damping
6. Sensor Temperature
Unit
1. NETWORK
2. PROCESS
VARIABLES
3. HART OUTPUT
4. ALERTS
5. VARIABLE
REMAPPING
1. Lower Sensor Trim
2. Upper Sensor Trim
3. Calibration Type
4. Sensor Trim Points
1. Pressure
2. Percent of Range
3. Sensor Temperature
4. Process Variable is
1. SENSOR TRIM
2. Recall Factory Trim
1. Zero trim
2. Lower Sensor Trim
3. Upper Sensor Trim
4. Calibration Type
5. Sensor Trim Points
1. Sensor Temperature
2. Sensor Temperature Unit
1. Pressure
2. Percent of Range
3. Sensor Temperature
4. Supply Voltage
5. Process Variable is
1. Process Variable is
2. Secondary Variable is
3. Tertiary Variable is
4. Quaternary Variable is
1. # of Diaphragm Seals
2. Seal Type
3. Seal Fill Fluid
4. Remote Seal Isolator
Material
1. Smart Power
2. Network ID
3. Set Join Key
4. Radio State
1. Power Mode
2. Transmit Rate
3. Database Mode
4. High Power Refresh
1. HI-HI Alert
2. HI Alert
3. LO Alert
4. LO-LO Alert 1. Configure Alert
2. Mode
3. Assigned Variable
4. Direction
5. Units
6. Set Point
7. Dead Band
1. Radio Model No.
2. Radio Type
3. Wireless Device Type
4. Get Unique ID
5. Radio SW Major Rev
6. Radio SW Minor Rev
7. Radio SW Build
8. Radio Hardware Rev
1. Logged Sensor Status
2. Clear Status Log

Reference Manual
00809-0100-4802, Rev BA
August 2007
2-5
Rosemount 3051S Wireless Series
Fast Key Sequence The following menu indicates fast key sequences for common functions. A
check (⻫) indicates the basic configuration parameters. At minimum, these
parameters should be verified as part of the configuration and startup
procedure.
CHECK OUTPUT Before performing other transmitter on-line operations, review the digital
output parameters to ensure that the transmitter is operating properly and is
configured to the appropriate process variables.
Process Variables The pressure output value in both engineering units and percent of range will
reflect the applied pressure even when the applied pressure is outside of the
configured range as long as the applied pressure is between the upper and
lower range limit of the transmitter. For example, if a Range 2 3051S_T (LRL
= 0 psi, URL = 150 psi) is ranged from 0 to 100 psi, an applied pressure of
150 psi will return a % of range output of 150% and an engineering output of
150 psi.
Field Communicator
The process variable menu displays the following process variables:
• Pressure
• Percent of Range
• Sensor Temperature
• Supply Voltage
Function HART Fast Key Sequence
⻫Damping 1, 3, 6
Date 1, 3, 4, 1
Descriptor 1, 3, 4, 2
Device Info 1, 3, 4
Field Device Information 1, 4, 4, 2
LCD Display Configuration 1, 3, 7
Lower Sensor Trim 1, 2, 2, 2, 1
Message 1, 3, 4, 3
Network 1, 4, 3, 1
Number of Requested Preambles 1, 4, 3, 3, 2
Poll Address 1, 4, 3, 3, 1
Range Values 1, 3, 3
Variable Re-mapping 1, 4, 3, 5
Rerange- Keypad Input 1, 2, 2, 1, 1
Sensor Information 1, 4, 4, 3
Sensor Temperature 1, 1, 3
Sensor Trim 1, 2, 2, 2
Sensor Trim Points 1, 2, 2, 2, 4
Status 1, 2, 1, 2
⻫Tag 1, 3, 1
⻫Transfer Function (Setting Output Type) 1, 3, 5
Transmitter Security (Write Protect) 1, 3, 4, 4
⻫Units (Process Variable) 1, 3, 2
Upper Sensor Trim 1, 2, 2, 2, 2
Zero Trim 1, 4, 1, 1, 2, 1, 1
Fast Keys 1, 1

Reference Manual
00809-0100-4802, Rev BA
August 2007
Rosemount 3051S Wireless Series
2-6
AMS
Right click on the device and select “Process Variables...” from the menu.The
process variable screen displays the following process variables:
• Pressure
• Percent of range
• Sensor temperature
• Supply Voltage
• Primary Variable (PV)
Sensor Temperature The 3051S Wireless contains a temperature sensor near the pressure sensor
in the SuperModule. This does not provide an accurate process temperature.
Field Communicator
Enter the fast key sequence “Sensor Temperature” to view the sensor
temperature reading.
AMS
Right click on the device and select “Process Variables...” from the menu.
“Snsr Temp” is the sensor temperature reading.
BASIC SETUP
Set Process Variable
Units
The PV Unit command sets the process variable units to allow you to monitor
your process using the appropriate units of measure.
Field Communicator
Enter the fast key sequence “Set Process Variable Units.” Select from the
following engineering units:
AMS
Right click on the device and select “Configure/Setup” from the menu. In the
Basic Setup tab, use “Unit” drop down menu to select units.
Set Output
(Transfer function)
The 3051S Wireless has two output settings: Linear and Square Root.
Activate the square root output option to make output proportional to flow. As
input approaches zero, the 3051S Wireless automatically switches to linear
output in order to ensure a more smooth, stable output near zero (see
Figure 2-2).
From 0 to 0.6 percent of the ranged pressure input, the slope of the curve is
unity (y = x). This allows accurate calibration near zero. Greater slopes would
cause large changes in output (for small changes at input). From 0.6 percent
to 0.8 percent, curve slope equals 42 (y = 42x) to achieve continuous
transition from linear to square root at the transition point.
Fast Keys 1, 1, 3
Fast Keys 1, 3, 2
•inH
2O • bar • torr
• inHg • mbar • atm
•ftH
2O•g/cm
2•MPa
• mmH2O • kg/cm2•inH
2O at 4 °C
• mmHg • Pa • mmH2O at 4 °C
•psi •kPa
Fast Keys 1, 3, 5

Reference Manual
00809-0100-4802, Rev BA
August 2007
2-7
Rosemount 3051S Wireless Series
Field Communicator
Enter the fast key sequence “Set Output (Transfer function).”
AMS
Right click on the device and select “Configure/Setup” from the menu.
1. In the Basic Setup tab, use “Xfer fnctn” drop down menu to select output,
click Apply.
2. After carefully reading the warning provided, select yes.
Figure 2-2. Square Root Output
Transition Point
Security (Write Protect) The 3051S Wireless has a software write protect security feature.
Field Communicator
Enter the fast key sequence “Transmitter Security” to view the Write Protect
setting.
AMS
Right click on the device and select “Configure/Setup” from the menu. In the
Basic Setup tab, review the Write Protect setting.
LCD DISPLAY The LCD display indicates output and abbreviated diagnostic messages.
NOTE
Use Rosemount Wireless LCD Part Number: 00753-9004-0002.
The LCD display features a four-line display and a bar graph. The first line of
five characters displays the output description, the second line of seven digits
displays the actual value, the third line of six characters displays engineering
units and the fourth line displays “Error” when the transmitter is in alarm. The
LCD display can also display diagnostic messages. The bar graph represents
the network connectivity status.
Sq. Root
Curve
Transition Point
Linear Section
Slope=1
Slope=42
Transition Point
Sq. Root Curve
Full Scale
Flow (%)
Fast Keys 1, 3, 4, 4

Reference Manual
00809-0100-4802, Rev BA
August 2007
Rosemount 3051S Wireless Series
2-8
See “LCD Screen Messages” on page 5-6 for more information on LCD
messages.
LCD Display Configuration
AMS
Right click on the device and select “Configure/Setup” from the menu.
1. Under “Device” in the “Smart Power” tab, select the desired LCD option
to suit your application needs, click Apply.
2. After carefully reading the warning provided, select yes.
DETAILED SETUP
Alerts Alerts allow the user to configure the transmitter to output a HART message
when the configured data point is exceeded. A process alert will be
transmitted continuously if the set points are exceeded and the alert mode is
ON. An alert will be displayed on a Field Communicator, AMS status screen or
in the error section of the LCD display. The alert will reset once the value
returns within range.
NOTE
HI alert value must be higher than the LO alert value. Both alert values must
be within the pressure or temperature sensor limits.
Example 1: Rising Alert
Example 2: Falling Alert
Fast Keys 1, 3, 7
Fast Keys 1, 4, 3, 4
Deadband
Assigned Value
Alert Set Point
Alert “OFF” Alert “ON” Alert “OFF”
Units of Measurement
Time
Deadband
Assigned Value
Alert Set Point
Alert “OFF” Alert “ON” Alert “OFF”
Units of Measurement
Time