Emerson Rosemount WPG User manual

Quick Start Guide
00825-0100-4145, Rev BA
February 2018
Rosemount™Smart Pressure Gauge

February 2018
2
Quick Start Guide
Required equipment
NOTICE
This guide provides basic guidelines for Rosemount Smart Pressure Gauges. It does not provide instructions
for configuration, diagnostics, maintenance, service, troubleshooting or intrinsically safe (I.S.) installations.
Refer to the Rosemount Smart Pressure Gauge Reference Manual for more instruction. The manual and this
guide are also available electronically on Emerson.com\Rosemount.
Shipping considerations
The device is shipped with the battery installed.
Each device contains one “D” size primary lithium-thionyl chloride battery. Primary lithium batteries are
regulated in transportation by the U.S. Department of Transportation, and are also covered by IATA
(International Air Transport Association), ICAO (International Civil Aviation Organization), and ARD
(European Ground Transportation of Dangerous Goods). It is the responsibility of the shipper to ensure
compliance with these or any other local requirements. Consult current regulations and requirements before
shipping.
Explosions could result in death or serious injury.
Installation of device in an explosive environment must be in accordance with appropriate local, national
and international standards, codes, and practices.
Ensure device is installed in accordance with intrinsically safe or non-incendive field practices.
Electrical shock can result in death or serious injury.
Care must be taken during transportation of device to prevent electrostatic charge build-up.
Device must be installed to ensure a minimum antenna separation distance of 8 in. (20 cm) from all
persons.
Process leaks could result in death or serious injury.
Handle the device carefully.
Failure to follow safe installation guidelines could result in death or serious injury.
Only qualified personnel should install the equipment.
Anti-seize paste or PTFE tape
(for NPT threaded connection)
Standard tools, e.g. screwdriver,
wrench, pliers
Contents
What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . 3
Optional: Power/device check . . . . . . . . . . . . . 4
Optional: Normal range indication option . . . 4
Installation Procedure . . . . . . . . . . . . . . . . . . . . . 5
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 7
Product Certifications . . . . . . . . . . . . . . . . . . . . . 8

Quick Start Guide
3
February 2018
What’s in the box
The following options are also available and will ship with the Rosemount Smart Pressure
Gauge if ordered.
Smart Pressure Gauge Quick Start Guide
Rosemount 306 Integral Manifold (model code S5) B4 bracket (model code B4)
Rosemount 1199 Seal (model code S1)
Product Certification (model codes below)
Q4: Calibration Cert
QG: Calibration Cert and GOST Verification Cert
QP: Calibration Cert and Tamper Evident Seal
Q8: Material Traceability cert per EN 102043.1
Q15: Cert of Compliance to NACE MR0175/ISO 15156 for
wetted materials
Q25: Cert of Compliance to NACE MR00103 for wetted
materials
Normal range Indication (model code LK)

February 2018
4
Quick Start Guide
1.0 Optional: Power/device check
The device is designed to be installation-ready. To check device battery prior
to installation, perform the following:
1. Perform “Turn on device” on page 6.
2. Slide the ON/OFF switch to the OFF position until ready for use.
2.0 Optional: Normal range indication option
Note
The stickers are intended to be installed on the dial only and should not be applied on
the inside or outside of the housing cover.
Stickers should be applied in an environment where the ambient temperature is above
50 °F (10 °C).
1. Modify each of the stickers to desired size.
2. Remove housing cover.
3. Slide ON/OFF switch to the OFF position and wait for LED to stop flashing.
4. Gently move the needle in the clockwise direction until it is pointing at the
Red X.
Note
Use caution as the electronics assembly is connected to the needle.
5. Remove any debris on the dial, so it does not become trapped under the
sticker.
6. Peel back the white paper backing of the sticker.
7. Slowly lower the sticker onto the surface of the dial in the desired location
and rub it in place firmly. Repeat steps 6and 7until desired indication
locations are set.
Note
Moving the sticker after initial contact is not recommended as this decreases the
amount of adhesive on the back of the sticker.
8. Slide ON/OFF switch to the ON position.
9. Replace housing cover.

Quick Start Guide
5
February 2018
3.0 Installation Procedure
Step 1: Seal and protect threads
Step 2: Mount device
Note
Use wrench on flats, not on housing.
Mounting orientation
The low side pressure port (atmospheric reference) is located in the neck of the
device behind the housing. The vent path is between the housing and sensor
(see Figure 1).
Figure 1. Low Side Pressure Port
A. Low side pressure port (atmospheric reference)
Keep the vent path free of any obstruction, including but not limited to paint, dust, and lubrication by
mounting the device so the process can drain away.
OR
A

February 2018
6
Quick Start Guide
Step 3: Turn on device
Check to ensure the device and battery are working properly.
1. Twist the cover counterclockwise to remove it.
2. Slide the OFF/ON switch to the ON position to initiate the power sequence.
Note
During the power sequence, the dial tests full range of motion and LED flashes amber.
3. Once the power sequence ends, verify the LED flashes green.
Note
The LED may display several colors; see Figure 1in “Troubleshooting” on page 7for
device statuses.
Step 4: Connect to device
Field Communicator
1. Turn on the Field Communicator.
2. From the Main menu, select the HART symbol.
AMS Configurator
1. Start AMS Configurator.
2. From the View menu, select Device Connection View.
3. Double click the device under the HART modem.
A. Field Communicator B. HART®Modem C. AMS Configurator
123
645
87
0
9
A
BC

Quick Start Guide
7
February 2018
Step 5: Eliminate mounting effects
Devices are factory-calibrated. Once installed, it is recommended to perform
this step to eliminate potential error caused by mounting position or static
pressure. Instructions for using a Field Communicator are listed below.
Note
See the Rosemount Smart Pressure Gauge Reference Manual for the following:
Using AMS Configurator
Sensor trim function on absolute gauge
1. Vent the device.
2. Connect the Field Communicator.
3. From the HOME screen, enter the HART Fast Key sequence.
4. Follow the commands to perform the procedure.
4.0 Troubleshooting
This section provides information for basic troubleshooting. See the Reference
Manual for advanced troubleshooting.
Device status
The flashing LED indicates device status using the colors descibed in Table 1.
Table 1. Status Descriptions
Pressure measurement
If the mounting effects have not been eliminated after completing Step 5,
perform this alternative procedure for verifying the pressure value.
1. From the HOME screen, eter the HART Fast Key sequence.
2. Follow the commands to perform the procedure.
Device dashboard Fast Keys 2, 1, 1
LED color Device status
Green Functioning properly
Amber Battery is low, battery replacement recommended
Red
Battery replacement required
OR
Device is malfunctioning
No
color No power, verify ON/OFF switch is in “on” position
Device dashboard Fast Keys 2, 2, 1, 1, 1

February 2018
8
Quick Start Guide
5.0 Product Certifications
Rev: 2.0
5.1 European Directive Information
A copy of the EU Declaration of Conformity can be found at the end of the
Quick Start Guide. The most recent revision of the EU Declaration of
Conformity can be found at www.Emerson.com/Rosemount.
5.2 Ordinary Location Certification from CSA
The product has been examined and tested to determine that the design
meets the basic electrical, mechanical, and fire protection requirements by
CSA, a nationally recognized test laboratory (NRTL) as accredited by the
Federal Occupational Safety and Health Administration (OSHA).
5.3 Installing in North America
The US National Electrical Code (NEC) and the Canadian Electrical Code (CEC)
permit the use of Division marked equipment in Zones and Zone marked
equipment in Divisions.The markings must be suitable for the area
classification, gas, and temperature class. This information is clearly defined
in the respective codes.
5.4 USA
I5 U.S.A. Intrinsically Safe (IS)
Certificate: [CSA] 70047656
Standards: FM 3600 – 2011, FM 3610 – 2010, UL Standard 50 – Eleventh Edition,
UL 61010-1 – 3rd Edition, ANSI/ISA-60079-0 (12.00.01) – 2013,
ANSI/ISA-60079-11 (12.02.01) – 2013, ANSI/IEC 60529 – 2004
Markings: IS CL I, DIV 1, GP A, B, C, D T4;
Class 1, Zone 0, AEx ia IIC T4 Ga;
T4 (–40 °C Ta+70 °C)
when installed per Rosemount drawing 00G45-1020;
Type 4X; IP66/67;
Special Conditions for Safe Use (X):
1. Do not replace battery when explosive atmosphere is present.
2. Use only 00G45-9000-0001 batteries.
3. The surface resistivity of the housing is greater than 1G . To avoid electrostatic
charge build-up, it must not be rubbed or cleaned with solvents or a dry cloth.
4. Substitution of components may impair intrinsic safety.
5.5 Canada
I6 Canada Intrinsically Safe (IS)
Certificate: [CSA] 70047656
Standards: CAN/CSA C22.2 No. 0-10, CAN/CSA C22.2 No. 94-M1991 (R2011),
CAN/CSA-60079-0-11, CAN/CSA-60079-11-14, CSA Std C22.2 No.
60529-05, CAN/CSA-C22.2 No. 61010-1-12


Quick Start Guide
9
February 2018
Markings: Intrinsically Safe for Class I, Division 1, Groups A, B, C, D T4;
Ex ia IIC T4 Ga
T4 (–50 °C Ta +70 °C)
when installed per Rosemount drawing 00G45-1020;
Type 4X; IP66/67;
Special Conditions for Safe Use (X):
1. Do not replace battery when explosive atmosphere is present.
Ne pas remplacer les accumulateurs si une atmosphère explosive peut être
présente.
2. Use only 00G45-9000-0001 batteries.
Utiliser uniquement des accumulateurs 00G45-9000-0001.
3. The surface resistivity of the housing is greater than 1G . To avoid electrostatic
charge build-up, it must not be rubbed or cleaned with solvents or a dry cloth.
La résistivité de surface du boÎtier est supérieure à un gigaohm. Pour éviter
l’accumulation de charge électrostatique, ne pas frotter ou nettoyer avec des
produits solvants ou un chiffon sec.
4. Substitution of components may impair intrinsic safety.
La substitution de composants peut compromettre la sécurité intrinsèque.
5.6 Europe
I1 ATEX Intrinsic Safety
Certificate: Baseefa16ATEX0005X
Standards: EN 60079-0: 2012 + A11: 2013, EN 60079-11: 2012
Markings: II 1 G Ex ia IIC T4 Ga, T4 (–40 °C Ta +70 °C)
IP66/67;
Special Conditions for Safe Use (X):
1. The plastic enclosure may constitute a potential electrostatic ignition risk and must
not be rubbed or cleaned with a dry cloth.
2. The measured capacitance between the equipment enclosure and metallic inline
sensor module is 4.7pF. This must be considered only when the SPG is integrated
into a system where the process connection is not grounded.
3. Do not change the battery when an explosive atmosphere is present.
4. Only replace battery with Rosemount Part No. 00G45-9000-0001.
5.7 International
I7 IECEx Intrinsic Safety
Certificate: IECEx BAS 16.0012X
Standards: IEC 60079-0: 2011, IEC 60079-11: 2011
Markings: Ex ia IIC T4 Ga, T4 (–40 °C Ta+70 °C)
IP66/67;
Special Conditions for Safe Use (X):
1. The plastic enclosure may constitute a potential electrostatic ignition risk and must
not be rubbed or cleaned with a dry cloth.
2. The measured capacitance between the equipment enclosure and metallic inline
sensor module is 4.7pF. This must be considered only when the SPG is integrated
into a system where the process connection is not grounded.
3. Do not change the battery when an explosive atmosphere is present.
4. Only replace battery with Rosemount Part No. 00G45-9000-0001.


February 2018
10
Quick Start Guide
Figure 2. Declaration of Conformity
EU Declaration of Conformity
No: RMD 1108 Rev. D
Page 1 of 3
We,
Rosemount Inc.
8200 Market Boulevard
Chanhassen, MN 55317-9685
USA
declare under our sole responsibility that the product,
Models WPG & SPG:
Wireless Pressure Gauge & Smart Pressure Gauge
manufactured by,
Rosemount Inc.
8200 Market Boulevard
Chanhassen, MN 55317-9685
USA
to which this declaration relates, is in conformity with the provisions of the European
Community Directives, including the latest amendments, as shown in the attached schedule.
Assumption of conformity is based on the application of the harmonized standards and, when
applicable or required, a European Community notified body certification, as shown in the
attached schedule.
(signature)
Vice President of Global Quality
(function name - printed)
Chris LaPoint
(name - printed)
28-Aug-2017
(date of issue)