Emerson E2 User manual

026-1400 Rev 2 12-APR-10
Facility Status Display (FSD)
Installation and
Operation Manual

3240 Town Point Drive NW Suite 100
Kennesaw, GA 30144, USA
Phone: [phone]
Fax: [phone]
ALL RIGHTS RESERVED.
The information contained in this manual has been carefully checked and is believed to be accurate. However, Com-
puter Process Controls, Inc. assumes no responsibility for any inaccuracies that may be contained herein. In no event will
Computer Process Controls, Inc. be liable for any direct, indirect, special, incidental, or consequential damages resulting
from any defect or omission in this manual, even if advised of the possibility of such damages. In the interest of continued
product development, Computer Process Controls, Inc. reserves the right to make improvements to this manual, and the
products described herein, at any time without notice or obligation.
CE/FCC COMPLIANCE NOTICE
Class A compliance for Facility Status Display under Part 15 of the FCC Rules and CE EN 55022. In a domestic envi-
ronment this product may cause radio interference in which case the user may be required to take adequate measures.
READ ALL INSTRUCTIONS CAREFULLY
If the equipment is not used in the manner specified by the manufacturer, the protection provided
by the equipment may be impaired.

Table of Contents • v
Table of Contents
1 INTRODUCTION.......................................................................................................................................................... 1
2 INSTALLATION........................................................................................................................................................... 2
2.1. WIRING......................................................................................................................................................................... 2
2.2. ALARM RELAYS............................................................................................................................................................ 3
2.3. MOUNTING.................................................................................................................................................................... 3
3 SET UP FSD AND E2 COMMUNICATION.............................................................................................................. 5
3.1. STEP 1: ADD FSD TO E2............................................................................................................................................. 5
3.2. STEP 2: SET UPIP ADDRESS FOR THE FSD................................................................................................................ 5
3.3. STEP 3: SET THE E2 IP ADDRESS IN FSD................................................................................................................... 6
4 ALARM OVERVIEW................................................................................................................................................... 7
4.1. ALARM FILTERING........................................................................................................................................................ 7
4.1.1. Alarm Snoozing..................................................................................................................................................... 7
5 FSD SCREEN NAVIGATION ..................................................................................................................................... 8
5.1. HOME SCREEN ............................................................................................................................................................. 8
5.2. ALARM LIST SCREEN ................................................................................................................................................... 8
5.2.1. Advisory Detail Screen ......................................................................................................................................... 9
5.3. DATA POINTS SCREEN ................................................................................................................................................. 9
5.3.1. Data Points Detail Screen .................................................................................................................................... 9
5.4. FSD CONFIGURATION................................................................................................................................................. 10
5.4.1. Alarms Tab.......................................................................................................................................................... 11
5.4.2. Communications Tab .......................................................................................................................................... 12
5.4.3. General Tab ........................................................................................................................................................ 12
5.4.4. About Tab............................................................................................................................................................ 12
5.4.5. Backlight Time-out Setting.................................................................................................................................. 13
6 E2 DATA POINT SETUP FOR FSD......................................................................................................................... 15
7 E2 ETHERNET PEER COMMUNICATIONS........................................................................................................ 17
7.1. ETHERNET IP CONFIGURATIONS ................................................................................................................................ 17
7.2. HARDWARE SPECIFICATIONS...................................................................................................................................... 17
7.2.1. Components......................................................................................................................................................... 17
7.3. SOFTWARE SPECIFICATIONS ....................................................................................................................................... 17
7.4. ETHERNET NETWORK LAYOUTS................................................................................................................................. 18
7.4.1. Closed Network Layout....................................................................................................................................... 18
7.4.2. Open Network Layout ......................................................................................................................................... 19
7.5. SOFTWARE SETUP....................................................................................................................................................... 19
7.6. TROUBLESHOOTING .................................................................................................................................................... 20
8 E2 ALARM ANNUNCIATOR SETUP...................................................................................................................... 21
9 SOFTWARE UPDATES............................................................................................................................................. 21
10 SPECIFICATIONS.................................................................................................................................................... 22

Introduction • 1
1Introduction
One of the most important features of the E2 facility
managementsystemistoputvitalsysteminformation
at the fingertips of the service technician or store man-
ager. The FSD reports alarm information and more,
(such as temperatures, occupancy, case status, and
setpoints) and provides a centralized device for store
personnel to review information by communicating
with the E2 via Ethernet connectivity (minimum E2
firmware revision 2.65F01).
The FSD has a touch screen color display for quick
navigation and can be mounted in a separate, remote
location from the E2 controller, which enables alarms
and other relevant store information to be viewed
from where it is most convenient for the user.
The FSD can be configured to filter out notices and/or
return-to-normal alarms, and provides a quick review
of all advisories and detailed advisory information.
The FSD also receives alerts and provides annunciat-
ed alarms and alarm information directly to store and
department managers. This compact unit can be in-
stalled virtually anywhere with a standard Ethernet
connection and 120V power source. Features include:
• 6” LCD touch screen (with backlight).
• Mounting plate for recessed installation.
• Audible alarm buzzer (with silence setting) and
red alarm LED (illuminates when there is an ac-
tive advisory).
• Auxiliary relay provides a dry contact closure
that follows the alarm relay output.
• Connectivity with E2 via TCP/IP Ethernet.
• Remote software upgrading of the FSD.
• Display of up to 200 alarms.
• Display of up to 150 customizable data points.
Figure 1-1 - Facility Status Display

2 • FSD Installation and Operation Guide 026-1400 Rev 2 12-APR-10
2 Installation
This section of the manual covers wiring and mounting for the FSD.
2.1. Wiring
1. Step 1: Using the fourscrews onthe front
of the mounting plate, unscrew the cover
of the FSD and remove, exposing the
back of the enclosure. Once the top has
been separated from the back of the en-
closure, unplug the 8-pin connector and
RS232 cable (Step 1 of Figure 2-1) from
the circuit board (P/N 537-1100).
2. Step 2: Mount the base enclosure and re-
fer to Section 2.3., Mounting for instruc-
tions.
3. Step 3: Once the unit has been mounted,
depending on the voltage input, wire ei-
ther 120VAC, 208VAC, or 240VAC Hot
leg to the corresponding terminal block
label. Then wire the Neutral or L2 leg to
the terminal block labeled Neutral. Wire
Ground to Ground as indicated byStep 3
of Figure 2-1.
4. Step 4: Open the ferrite (P/N 090-0008)
and run the Ethernet cable through, wrap-
ping the cable around the ferrite twice
(two turns), near the Ethernet port (LAN)
on the back of the display, and close the
ferrite (Figure 2-2) around the Ethernet
cable.
5. Step 5: Plug the Ethernet cable into the
RJ45 connector (LAN) on the back of the
NOTE: Provide either 120VAC, 208VAC,
or 240VAC (40VA max) to the FSD termi-
nal block through a store circuit breaker.
The breaker size should be 20 amps or less.
Figure 2-1 - 8-Pin Connector and RS232 Cable Connections
Figure 2-2 - Ferrite Installation on Ethernet Cable
Inside Back of Enclosure
9.0”
STEP 3
8.0”
Transformer
Ground
120VAC
Neutral
208VAC
240VAC
Hot in
FSD Circuit
Board
RS232
A
U
X
+
+
_
+__
Earth
Ground
Alarm
LED
HornVdeOut
Display
STEP 1

Alarm Relays Installation • 3
FSD’sdisplaymodule(P/N 750-5100)as
indicated by Step 5 of Figure 2-3.
6. Step 6: Reconnect the 8-pin connector
and RS232 cable to the circuit board in
Step 6 of Figure 2-3.
7. Step 7: Replace the mounting plate back
onto the enclosure and attach using the
four screws.
2.2. Alarm Relays
• An audible alarm will sound when a new advi-
sory has been received.
• The red alarm LED on the front of the display
module illuminates any time there is an active
advisory.
• The auxiliary relay (dry contact closure) will
activate any time there is an active advisory.
This output allows an external alarm indicator
to be installed away from the board.
2.3. Mounting
The FSD is recess-mounted into a wall or other
mounting surface. The face plate with the LCD dis-
play (front portion of the unit) will mount flush
against the surface around the outside of the opening
once the power supply box has been mounted inside
the wall.
1. Cut a rectangular hole into the mounting
surface 8.0” high by 9.0” wide, byat least
3.875” deep (20.32 cm high by 22.86 cm
wide by at least 9.84 cm deep). When
cutting the mounting hole, allow at least
1/2” (1.27 cm) clearance around the hole
for face plate mounting (Figure 2-5).
2. Once this hole is cut, mount the unit as
desired (Figure 2-4), and position the en-
closure so that the four support tabs are
flush against the outside lip of the open-
ing in the wall.
3. Use a screwdriver to bend the four push-
out tabs (two on each side) against the
inside of the drywall so that they hold the
power supply box in place.
Figure 2-3 - Wiring Layout of FSD Enclosure
Inside Back of Enclosure
9.0”
8.0”
Transformer
Back of FSD Panel
LAN
COM1COM2
COM3
GND
-vdc
+vdc
FSD Circuit
Board
R
S
2
3
2
A
U
X
+
+
_
+
_
_
E
a
r
t
h
G
r
o
u
n
d
Alarm
LED
HornVdeOut
Display
STEP 5
STEP 6
ON/OFF
Switch
NOTE: Do not exceed the maximum
Ethernet cable length of 328 feet (100 me-
ters).

4 • FSD Installation and Operation Guide 026-1400 Rev 2 12-APR-10
Figure 2-4 - Mounting The Power Supply Box
Figure 2-5 - Leave 1/2” For Face Plate Mounting
Open Side of
Power Supply Box
Mount Back Portion of FSD Power Supply Box
Inside Wall
9.0”
8.0”
Support
Tabs (4)
3.875”
Push-out
Tabs
Conduit
Knock-outs
Drawing Not To Scale
Face Plate
Screw Holes (4)
Open Side of
Power Supply Box
9.0”
8.0”
1/2”
1/2”
leave ½” clearance
each side for face plate
1/2”
1/2”