Empire Comfort Systems INTERMITTENT PILOT DVCD36FP70 User manual
Page 1
DIRECT VENT
ZERO CLEARANCE GAS
FIREPLACE HEATER SERIES:
MILLIVOLT (MV)
dvcd(32,36,42)fP3(0,1)(n,P)-4
INTERMITTENT PILOT (IP)
dvcd(32,36,42)fP7(0,1)(n,P)-4
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
— Do not store or use gasoline or other
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
service agency or the gas supplier.
aftermarket, permanently located,
This appliance is only for use with the type
of gas indicated on the rating plate. This
GAS-FIRED
HOT GLASS
DO NOT TOUCH
NEVER
WILL
CAUSE BURNS.
GLASS
UNTIL COOLED.
ALLOW CHILDREN
TO TOUCH GLASS.
DANGER
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and shall
be installed for the protection of children and other at-risk
individuals.
INSTALLATION INSTRUCTIONS
38712-2-0719Page 2
TABLE OF CONTENTS
3
4
5
5
6
6
7
7
10
11
12
14
14
16
19
23
24
25
26
27
30
31
32
34
36
39
40
49
50
59
70
71
72
73
74
75
90
91
91
92
93-95
SECTION PAGE
38712-2-0719 Page 3
DANGER
Indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
NOTICE:
Television Considerations
“”
BEFORE YOU START
See Figure 1.
Preparation
VALVE
RATING
PLATE
LIGHTING
INSTRUCTION
PLATE
Figure 1
38712-2-0719Page 4
CARTON CONTENTS & HARDWARE PACK
LOG SET
Decorative
Rock
Rockwool
12
3
4
6
5
7
10
9
11
8
13
12
Description Quantity Supplied Location
MV IP
1 1 1
2 1 1
3 1 1
4 1 1
5 1 1
6 1 1
7 2 2
1 1
9 1 1
10 0 1
11 0 4
12 1 1
13 1 1
NOTE:
#10 X ½” HEX HEAD SCREW (QTY. 8)
NAILING FLANGES (QTY. 4)
#8-18 X BLACK (QTY. 2)½” PAN HEAD SCREW
38712-2-0719 Page 5
INTRODUCTION
Instructions to Installer
Notes to Installer
WARNING
poisoning.
“
”
High Altitude
EMPIRE COMFORT
SYSTEMS
Canadian High Altitude
HOMEOWNER REFERENCE INFORMATION
_____________________________ ________________________
_____________________________ _____________________
______________________________ _________________________
______________________________________________________________________________
38712-2-0719Page 6
ACCESSORIES
ACCESSORIES
Description Model
fBB4
NOTICE
CONTROL OPTIONS
Description Model
VENT KITS
Part No. Description
dvvK4TSP
dvvK4TP
dvvK4vP
dvvK4f
)
CONVERSION KITS
Kit # Conversion Type Used On
dvcd32fP3
dvcd32fP3
dvcd36fP3
dvcd36fP3
dvcd42fP3
dvcd42fP3
dvcd32fP7
dvcd32fP7
31759 dvcd36fP7
dvcd36fP7
31761 dvcd42fP7
31760 dvcd42fP7
SPECIFICATIONS
DVCD32
Natural Gas
DVCD32
Propane Gas
DVCD36
Natural Gas
DVCD36
Propane Gas
DVCD42
Natural Gas
DVCD42
Propane Gas
20,000 20,000 25,000 25,000
14,000 14,000 14,000 16,500 19,500
)
)
NOTICE
GAS SUPPLY PRESSURES (inches water column)
Gas Type Maximum Minimum Manifold
38712-2-0719 Page 7
CEILING FIRE STOP
90° ELBOW
90° ELBOW
OR
45° ELBOW
WALL STRAP
PIPE LENGTH
WALL THIMBLE
HORIZONTAL
TERMINATION
(MAXIMUM OF
THREE 90° ELBOWS)
VERTICAL
TERMINATION
(MAXIMUM OF
THREE 90° ELBOWS)
STORM COLLAR
ROOF FLASHING
Figure 2
VENT SYSTEM IDENTIFICATION
Special venting components
Special DV Vent Kits
dvvK-4vP
dvvK-4TP
dvvK-4TSP
dvvK-4fv
NOTICE:
SPECIAL VENT SYSTEMS
The following 4 x 6-5/8 inch
38712-2-0719
Figure 3
FIREPLACE DIMENSIONS
G
I1
J1
P1
TOP VENTING
LEFT VIEW
C
O
N
S
E
B
D
Q
FRONT VIEW
T
K
LM
RIGHT VIEW
ZX
Y
REAR VENTING
P2
J2
I2
CORNER INSTALL
H
AR
38712-2-0719 Page 9
FIREPLACE DIMENSIONS
SIDE STANDOFF
INSTALLED NAILING
FLANGES
GAS LINE
ACCESS
BARRIER SCREEN ASSEMBL
Y
&
GLASS FRAME ASSEMBLY
VENT COLLAR
GAS CONTROL AND
SWITCHES INSIDE
RATING PLATE AND
LABELS INSIDE
TOPSTANDOFF
Figure 4
INDEX
LETTER DIMENSION DESCRIPTION DVCD32 DVCD36 DVCD42
Dimensions in Inches
B
c
d
31 34 40
f
H 666
J1 777
J2
K
L 10 10 10
666
n 20 20 22
P1
P2
S
T
X
42
38712-2-0719Page 10
CLEARANCES
CLEARANCE TO COMBUSTIBLES
DIM. IN INCHES
0
0
0
0
0
BARRIER SCREEN
&
GLASS FRONT
2" x 4" BOTTOM PLATE
INSTALLED
NAILING
FLANGES
STAND OFF
6” (76mm) HEIGHT
ABOVE TOP OF
FIREPLACE
FINISHED WALL
(COMBUSTIBLE)
SEE MANTEL CHART FOR
MAXIMUM MANTEL DEPTH
SEE MANTEL CHART FOR
MINIMUM HEIGHT OF
MANTEL ABOVE HOOD
FINISHED WITH
NON-COMBUSTIBLE
MATERIAL AS DESIRED
Figure 5
NOTICE:
FIREPLACE
(TOP VIEW)
FRONT
FACE
(SIDE)
COMBUSTIBLE
MATERIALS ALLOWED
IN SHADED AREAS
3
MAX.
6
PERPENDICULAR
SIDE WALL
45°
HOOD
Figure 6
Mantel Chart
CANOPY
FIREBOX
FACE
84”
MIN.
(CEILING TO FLOOR)
CEILING
FLOOR
WALL
FACING
A
B
C
D
E
F
10”
20 1/4”
MIN.
10 1/4”
MIN.
41”
MIN.
COMBUSTIBLES
ALLOWED
WALL
STUD
TOP OF CANOPY
INDEX
LETTER
DISTANCE FROM
WALL FACING
DISTANCE FROM
TOP OF CANOPY
Dimensions in inches
2
B 4
c 6
d
10
f 12
Figure 7
Clearances
41” (91.4 mm)
MINIMUM
6” (152 mm)
MINIMUM
Figure 8
38712-2-0719 Page 11
Figure 9
NOTICE
LOCATING FIREPLACE
38712-2-0719Page 12
GAS SUPPLY
GAS LINE HOLE
(BOTH SIDES)
10”
2”
FROM FRONT OF
FIREPLACE TO
GAS LINE HOLE
Figure 10
RECOMMENDED GAS PIPE DIAMETER
Pipe
Length
Schedule 40 Pipe
Inside Diameter
Outside Diameter
Natural Propane Natural Propane
(Dimensions in inches)
NOTICE
NOTICE
FLEXIBLE GAS LINE CONNECTION
GAS SUPPLY
TEE HANDLE
FLEX TUBING
FLARE FITTING FLARE SHUT
OFF VALVE
Figure 11
See
Figure 12.
GAS SUPPLY PIPING
SHUT-OFF VALVE
GAS SUPPLY
INLET
1/8 NPT PLUGGED HOLE
FOR TEST GAGE
3” MINIMUM
GROUND JOINT UNIO
N
DRIP LEG
CAP
Figure 12
38712-2-0719 Page 13
Installing a New Main Gas Supply Shut-off Valve (Check
Local Code)
NOTICE
WARNING
If one of the test procedures results in pressures in excess
of 1/2 psig (14 inches
valve, it will result in a hazardous condition.
Checking Manifold Pressures
Gas Supply Pressure (inches w.c.)
Minimum Normal Maximum
Manifold Pressure (inches w.c.)
Normal (HI)
HI/LO REGULATOR
CONTROL KNOB
OUTLET
PRESSURE
TAP
INLET
PRESSURE
TAP
Figure 13 - Millivolt Valve
OUTLET PRESSURE TAP
INLET PRESSURE TAP
Figure 14 - IP Valve
38712-2-0719Page 14
JUNCTION BOX WIRING (FOR OPTIONAL BLOWER)
CAUTION
Before making the electrical connection, make sure that the
Electrical Code ANSI/NFPA 70 (latest edition).
STANDARD MILLIVOLT VALVE MODELS
Figure 15
INSTALLATION
NOTICE:
Framing Information
Figure 16
CAUTION
and verify framing methods and wall covering details.
HEADER
DIMENSIONS (IN INCHES)
DVCD32 DVCD36 DVCD42
39 39 41
B
c
Figure 16
38712-2-0719 Page 15
Frame the Fireplace Opening
PLATE
Figure 17
NOT USED
½” BOARD
5/8”
BOARD
USED TO
AT
TACH TO
FRAMING
Figure 18
Figure 19
See Figure 20.
NAIL OR OTHER SUITABLE FASTENER
Figure 20
38712-2-0719Page 16
Install the Canopy
Figure 21.
NOTICE
See Figure 21.
HEAT
SHIELD
CANOPY
Figure 21
NOTICE
See Figure 22.
See Figures 23
and 24.
Cold Climate Installation Recommendation
Figure 22
VENT PIPE CLEARANCE
Finishing
Figure 7 on page 10
WARNING
installation may cause a hazardous situation.
CAUTION
Failure to use the 300°F minimum adhesive may allow the
NOTICE
6-5/8” Diameter
intake vent
4” Diameter flue
Combustibles NOT
allowed in shaded
area
Top of Vent
3” (76 mm)
1” (25 mm)
1”
(25 mm)
Figure 23 - Hard Pipe Vent Clearance
38712-2-0719 Page 17
11”
(297 mm)
MIN.
9 1/8”
(232 mm)
MIN.
OUTSIDE THIMBLE ASSEMBLY
INSIDE THIMBLE ASSEMBLY
EXTERIOR
SHEAVING
Figure 24
VENT PIPE CLEARANCE
3” (76mm)
MINIMUM CLEARANCE
TO COMBUSTIBLES
VENT CAP/
THIMBLE
WALL FIRESTOP
DVCD(32,36)
47 ½”
(121 cm)
TO BOTTOM
OF UNIT
DVCD42
49 ½”
(126 cm)
TO BOTTOM
OF UNIT
Figure 25
Horizontal Only, Straight Out the Back
“A”
PIPE LENGTH
VENT CAP
WALL FIRESTOP/
THIMBLE
“B”
DIMENSIONS (INCHES) Models
A B
6 dvcd(32,36,42)
9 dvcd(32,36,42)
12 dvcd(32,36,42)
Figure 26
38712-2-0719
90° ELBOW “A”
PIPE
LENGTH
VENT CAP
WALL FIRESTOP/
THIMBLE
“B”
“C”
DIMENSIONS (INCHES)
A B C
6
9
12
Figure 27
Wall
WALL FIRESTOP/
THIMBLE
VENT
CAP
6” (152 mm)
MINIMUM
9” (229 mm)
MINIMUM
“B”
“C”
Dimensions (inches)
B C
DVCD32 DVCD36 DVCD42 DVCD(32,36,42)
Figure 28
the Wall
WALL FIRESTOP/
THIMBLE
“A”
PIPE LENGTH
VENT CAP
“B”
Reference
Letter
DVCD32 DVCD36 DVCD42
Dimension (inches)
BBB
6
9
12
Figure 29
VENT PIPE CLEARANCE
38712-2-0719 Page 19
To Use the Vent Graph
EXAMPLE A:
EXAMPLE B:
SPECIAL NOTE:
Example:
NOTICE:
Figure 30
Venting Graph (Dimensions in Feet)
TOP EXIT - VERTICAL AND HORIZONTAL TERMINATION
(DIMENSIONS IN FEET)
VERTICAL DIMENSION FROM THE BOTTOM OF THE UNIT TO THE CENTER OF THE
FLUE OUTLET WITH VERTICAL OR HORIZONTAL TERMINATION CAPS
TO
P VENT
CONNECTION
(HEIGHT
MAY
VA
RY WITH
MODEL)
HORIZONTAL RUN
VENTING FIREPLACE - TOP
38712-2-0719Page 20
VENTING FIREPLACE - TOP
SEE GRAPH FOR PERMISSIBLE “H” AND “V” DIMENSIONS
FIRESTOP AT
CEILING LEVEL
IF PENATRATING
CEILING
H
V
Figure 32
Below Grade Installation
12
The 7
and proper drainage around the termination area if the
3” (76mm)
MINIMUM
PIPE STRAP
48”
(1219mm)
COMBUSTIBLE
PROJECTION
18” (457mm)
MINIMUM
12” (305mm)
ABOVE GRADE OR
EXPECTED SNOW LEVEL
TYPICAL BASEMENT INSTALLATION
Figure 31
ATTENTION
This manual suits for next models
37
Table of contents
Other Empire Comfort Systems Indoor Fireplace manuals
Empire Comfort Systems
Empire Comfort Systems MILLIVOLT DVCP3630-1 Quick start guide
Empire Comfort Systems
Empire Comfort Systems FG28BM Series User manual
Empire Comfort Systems
Empire Comfort Systems LS38DF-1 Quick start guide
Empire Comfort Systems
Empire Comfort Systems MANTIS BF28(B User manual
Empire Comfort Systems
Empire Comfort Systems DV33IN33N-4 Quick start guide
Empire Comfort Systems
Empire Comfort Systems Boulevard LS41THF-1 Quick start guide
Empire Comfort Systems
Empire Comfort Systems LA21-1 User manual
Empire Comfort Systems
Empire Comfort Systems OP32FB2MF-2 Quick start guide
Empire Comfort Systems
Empire Comfort Systems DV25IN33L-3 Quick start guide
Empire Comfort Systems
Empire Comfort Systems DVCP36PP30 Series Quick start guide
Empire Comfort Systems
Empire Comfort Systems VFD26FM series User manual
Empire Comfort Systems
Empire Comfort Systems Boulevard VFLL60FP90LP-1 User manual
Empire Comfort Systems
Empire Comfort Systems VFD32FB0F-4 Quick start guide
Empire Comfort Systems
Empire Comfort Systems VFP32FB0L Quick start guide
Empire Comfort Systems
Empire Comfort Systems LTH1118ST-1 User manual
Empire Comfort Systems
Empire Comfort Systems DVLT42FP92N-2 Quick start guide
Empire Comfort Systems
Empire Comfort Systems DVCT35CBN95N User manual
Empire Comfort Systems
Empire Comfort Systems OP32FB2MF-1 User manual
Empire Comfort Systems
Empire Comfort Systems DVP36CPKR-1 User manual
Empire Comfort Systems
Empire Comfort Systems DVP42FP3 Quick start guide
Empire Comfort Systems
Empire Comfort Systems VFSE-18-1 User manual
Empire Comfort Systems
Empire Comfort Systems DVL25IN33N-1 User manual
Empire Comfort Systems
Empire Comfort Systems White Mountain Hearth MULTIFUNCTION REMOTE... Quick start guide
Empire Comfort Systems
Empire Comfort Systems HYDRAULIC Quick start guide
Popular Indoor Fireplace manuals by other brands
Napoleon
Napoleon NEFL42CHD-1 manual
Masport
Masport WOOD FIRE installation guide
JAYLINE
JAYLINE SS280 Installation & operation instructions
Heat-N-Glo
Heat-N-Glo SL-32S Installation
kozy heat
kozy heat Bellingham 52 quick start guide
Paragon Fires
Paragon Fires ROOM SEALED INSET LIVE FUEL EFFECT GAS FIRE owner's manual
Monessen Hearth
Monessen Hearth LCUF32CR-B Installation & owner's manual
PuraFlame
PuraFlame Galena owner's manual
Dimplex
Dimplex Toluca Deluxe instruction manual
SEI
SEI TENNYSON FA8544AO Assembly instructions
Dru
Dru G25 installation manual
Capital fireplaces
Capital fireplaces Designline DL700 Installation and user instructions
IronStrike
IronStrike VINTAGE VINT-DVS-U Installation and operation
ACR Heat
ACR Heat HERITAGE N25 Installation and operating instruction manual
European Home
European Home HVF-42 Installation, operation and owner's manual
Quadra-Fire
Quadra-Fire MTVERNINSAE-MBK Owner's manual operation & care
Harman Home Heating
Harman Home Heating Accentra Insert Installation & operating manual
Trimline Fires
Trimline Fires Zircon 1024 installation instructions