Empire Comfort Systems OP32FB2MF-2 Quick start guide
Page 1
INSTALLATION INSTRUCTIONS
AND OWNER'S MANUAL
OUTDOOR VENTLESS FIREBOX
OP32FB2MF-2
OP36FB2MF-2
OP42FB2MF-2
Premium Ventless Universal Fireboxes
EMPIRE
EMPIRE
Comfort Systems
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
vapors and liquids in the vicinity of this or any
other appliance.
— Installation and service must be performed by a
-
plier.
WARNING
If the information in these instructions are not fol-
WARNING
instructions thoroughly before installing or servicing
this equipment.
WARNING
For Outdoor Use Only.
WARNING
expose you to substances in fuel or from fuel combus-
tion which can cause death or serious illness.
WARNING
If you smell gas:
1. Shut off gas to the appliance.
2.
3.
-
partment.
WARNING
-
pors and liquids in the vicinity of this or any other
appliance.
An LP-cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.
GAS-FIRED
32273-0-0713Page 2
SECTION PAGE
Important Safety Information....................................................................................3
Introduction ...........................................................................................................4-5
Clearances ...............................................................................................................6
Combustible Materials..............................................................................................6
Outer Firebox Dimensions .......................................................................................7
Inner Firebox Dimensions ........................................................................................8
Planning Installation ............................................................................................9-10
Firebox Framing and Installation.......................................................................10-11
Gas Line Connection..............................................................................................12
Master Parts Distributor List...................................................................................13
How To Order Repair Parts ....................................................................................13
Parts List ................................................................................................................14
Parts View ..............................................................................................................15
Warranty Terms ......................................................................................................16
TABLE OF CONTENTS
32273-0-0713 Page 3
Installer: Please leave these instructions with the owner for
future reference
This unit complies with ANSI Z21.97/CSA 2.41 and CSA 4.96
U.S. for Outdoor Gas Fireboxes.
Children and adults should be alerted to the hazard of high
surface temperature and should stay away to avoid burns
or clothing ignition.
Young children should be carefully supervised when they
are in the same area with the appliance.
Installation and repair should be done by a QUALIFIED
SERVICE PERSON. This appliance should be inspected
before use and at least annually by a professional service
person. More frequent cleaning may be required due to
during operation.
off during initial operation of the appliance. This is a normal
temporary occurrence.
WARNING: Keep appliance area clear and free from
and liquids.
can be dangerous. Improper installation or use of the gas
explosion or carbon monoxide poisoning.
and ventilation air or in the absence of local codes follow
Do not operate this log set with glass doors in the closed
set is burning.
Inspect the hose before each use of the appliance.
The hose assembly must be replaced prior to the ap-
pliance being into operation if there is evidence of ex-
Inspect the burner at least once a year.
IMPORTANT SAFETY INFORMATION
DO NOT OPERATE THIS APPLIANCE WITH GLASS DOORS CLOSED.
DANGER: Indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING: Indicates a hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION: Indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE: Addresses practices not related to personal in-
jury.
high surface temperatures and should stay away to avoid
burns or clothing ignition.
are in the same area as the appliance.
on or near the appliance.
operation.
they are burned off during initial operation of the appliance.
This is a normal temporary occurrence.
Installation and repair should be done by a QUALIFIED
SERVICE PERSON. The appliance should be inspected
person. More frequent cleaning may be required due to
clean.
liquids.
A yearly examination and cleaning of the venting system
Clean and replace damaged parts.
use this appliance if any part has been under
to inspect the appliance and to replace any part of the
control system and any gas control which has been under
water.
32273-0-0713Page 4
Screened Porch Installation
be installed in a screen porch with the following guidelines.
Minimum Porch Area 96 sq. feet (9 sq m)
Minimum Ceiling Height 92" (234 cm)
See page 9.
Installation on Rugs and Tile
If this appliance is installed directly on carpeting, tile or other
be installed on a metal or wood panel extending the full width and
depth of the appliance.
used on wood stoves. The protection is for rugs that are extremely
thick and light colored tile.
Solid-fuels shall not be burned in a masonry or UL 127 factory-built
Installation and replacement of gas piping, gas utilization equipment
or accessories and repair and servicing of equipment shall be
person or through a representative is engaged in and is responsible for
(a) the installation or replacement of gas piping or (b) the connection,
installation, repair or servicing of equipment, who is experienced in
such work, familiar with all precautions required and has complied
with all the requirements of the authority having jurisdiction.
State of Massachusetts: The installation must be made by
Massachusetts.
The installation must conform with local codes or, in the absence of
local codes, with the National Fuel Gas Code, ANSI Z223.1.*
*Available from theAmerican National Standards Institute, Inc. 1430
Broadway, New York, N.Y. 10018.
Instructions to Installer
1. Installer must leave instruction manual with owner after
installation.
Always consult your local Building Department regarding regulations,
codes or ordinances which apply to the installation of an ventless
room heater.
*Aftermarket: Completion of sale, not for purpose of resale, from
the manufacturer.
This appliance is only for use with the type of gas indicated on the
rating plate.
WARNING
ANY CHANGE TO THIS APPLIANCE OR ITS CONTROLS CAN
Improper installation or use of the appliance can cause se-
monoxide poisoning.
Standard Z21.97 as an Outdoor Ventless Firebox and should be
installed according to these instructions.
shown in these instructions is the responsibility of the person
Important
All correspondence should refer to complete Model Number, and
Serial Number.
Moisture Resistance
not waterproof. Water and condensing water vapor may enter the
chase under certain conditions.
walls or on moisture sensitive surfaces.
When installed on exterior walls: Empire Comfort Systems
detail similar to that required for attached decks. Chase platforms,
including hearths should slope away from the structure at 1/4 in per
When installed on surfaces where water may collect or cause
damage: Empire Comfort Systems recommends a slope of 1/8 in
be shimmed level.
at 1/8 in to 1/4 in per foot. Metal safety strips must be on top of
any combustible hearth materials used for moisture management.
buy a weather cover or glass door accessory to protect the unit
from moisture. Never install a burner where moisture cannot drain
off easily. We recommend a weather barrier - such as a cover or
bifold glass doors - to protect the burner from moisture.
INTRODUCTION
32273-0-0713 Page 5
INTRODUCTION
the installation must conform with local codes, or in the ab-
sence of local codes with the National Fuel Gas Code, ANSI
Z223.1/NFPA 54, or International Fuel Gas Code.
When installed, the appliance must be electrically grounded
in accordance with local codes, or in the absence of local
codes with the National Electrical Code, ANSI/NFPA 70, if
applicable.
Solid fuels shall not be burned in this appliance.
The maximum gas inlet supply pressure is 13" for LP and
10.5" for NAT.
with an appliance gas pressure regulator, the required mani-
fold pressure in inches water column: 10" for LP and 3.5"
NAT.
with an appliance gas pressure regulator, the appliance and
its individual shutoff valve must be disconnected from the
gas supply piping system during any pressure testing of that
system at test pressures in excess of 1/2 psi (3.5 kPa).
The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psi (3.5 kPa).
For an appliance designed for use with a non-disposable self-
contained LP-gas supply system:
Propane cylinders may be acceptable for use with the ap-
pliance provided they are compatible with the appliance
retention means.
LP-gas supply cylinder must be constructed and marked
in accordance with the U.S. Department of Transportation
(D.O.T.) Specications for LP-Gas Cylinders, or the Stan-
dard for Cylinders, Spheres and Tubes for Transportation
of Dangerous Goods and Commission, CAN/CSA-B339 as
applicable.
LP-gas supply cylinders between 4 and 40 pounds must
LP-gas supply cylinder must have a connection device com-
patible with the connection of the appliance.
If the appliance is equipped with a CGA No. 600 Cylinder
Connection Device, the cylinder must be disconnected when
the appliance is not in use.
If appliance is to be permanently connected to a gas piping
system from a remote supply tank, installation must be in ac-
cordance with local codes or, in the absence of local codes,
with the National Fuel Gas Codes ANSI Z223.1/NFPA 54.
Enclosures for LP-gas supply cylinders shall be ventilated by
effectiveness of the opening(s) for purposes of ventilation shall
be determined with the LP-gas supply cylinder(s) in place. This
shall be accomplished by one of the following.
a. One side of the enclosure shall be completely open; or
b. For an enclosure having four sides, a top and a bottom:
1. At least two ventilation openings at cylinder valve
level shall be provided in the side wall, equally
sized, spaced at 180 degrees (3.14rad), and unob-
structed. Each opening shall have a total free area
of not less than 1/2 square inch per pound (2.3 sq.
cm/kg) of stored fuel capacity and not less than a
total free area of 10 square inches (64.5 sq. cm).
level and shall have a total free area of not less
than 1/2 square inch per pound (3.2 sq. cm/kg) of
stored fuel capacity and not less than a total free
area of 10 square inches (64.5 sq. cm). If ventila-
shall be at least two openings. The bottom of the
The openings shall be equally sized, spaced at 180
degrees (3.14 rad) and unobstructed.
3. Every opening shall have minimum dimensions so
as to permit the entrance of a 1/8 inch (3.2 mm)
diameter rod.
Cylinder valves shall be readily accessible for hand opera-
tion. A door on the enclosure to gain access to the cylinder
valves is acceptable, provided it is non-locking and can be
opened without the use of tools.
There shall be a minimum clearance of 2 inches (51 mm)
cylinder enclosure and the ground.
The design of the appliance shall be such that (1) the LP-gas
supply cylinder(s) can be connected, disconnected and the
connections inspected and tested outside the cylinder en-
closure; and (2) those connections which could be disturbed
when installing the cylinder(s) in the enclosure can be leak
tested inside the enclosure;
Cleaning Instructions
This appliance is built using mostly high-grade stainless steel to
resist rust-through. In outdoor applications, all stainless steel will
develop a dull patina and, depending on the local environment
and on the materials used in the installation, may develop some
surface oxidation (rust). This does not affect the performance
required with stainless steel cleaner.
When installation application includes highly acidic applications
such as mortar or stone etching, do not remove the protective
the appliance be cleaned with a stainless steel cleaner immedi-
ately.
hems, etc.) may require extra cleaning due to the properties of
32273-0-0713Page 6
Minimum Wall and Ceiling Clearances
Sidewall and Back Clearances: The clearance from the
less than 2".
Ceiling Clearances: The ceiling height should not be less
than 36" from the top of the hood.
installed, it must meet the clearance requirements detailed
in Figure 1..
Figure 1
Mantel Clearances
CLEARANCES
Figure 2
No greeting cards, stockings or ornamentation of any type should
Figure 3
COMBUSTIBLE MATERIALS
32273-0-0713 Page 7
OUTER FIREBOX DIMENSIONS
DIMENSIONS (in inches)
INDEX
LETTER OP32FB2MF OP36FB2MF OP42FBMF
A 39-7/8 41-7/8 41-7/8
B 36-5/8 41-5/8 43-1/8
C 17-1/16 19-1/4 19-1/4
D 28-1/4 32-1/4 36-1/4
E 32-7/8 34-7/8 34-7/8
F 31 36 40
G 22-1/4 24 24
H 6-1/8 6-3/8 6-3/8
I 28-3/8 30-3/8 30-3/8
J 8-3/4 8-3/8 8-3/8
K 5-7/16 5-1/4 5-1/4
L 33-1/4 37-5/8 39-5/8
M 66-7/16 75-3/8 79-1/4
32273-0-0713Page 8
INNER FIREBOX DIMENSIONS
E
B
A
C
D
TOP VIEW SIDE VIEW
INDEX
LETTER OP32FB2MF OP36FB2MF OP42FBMF
A 29 1/8” 34 1/8” 38 1/8”
B 23 5/8” 27 5/8” 31 5/8”
C 12 7/8” 15 5/16” 15 5/16”
D 17 5/16” 18 3/4” 18 3/4”
E 20 9/16” 22 9/16” 22 9/16”
32273-0-0713 Page 9
where the unit is to be installed and whether optional accessories
are desired. Gas supply piping should also be planned at this time.
2. A raised platform non-combustible material.
perimeter edges on the bottom of the unit.
(Example: Four concrete masonry blocks.)
or wood panel extending the full width and depth of the unit.
At this point, you should have decided what components to include
has not been done, stop and consult your dealer for assistance
with this planning.
ventilated space and shall NOT be used in a building, garage, or
other enclosed area.
soot. These issues are nuisance issues rather than a safety issues.
Typical installation may include covered patio, screened porch,
gazebo or an outside wall of a house.
Minimum porch area – 96 square feet
Minimum ceiling height – 92 inches
Outdoor Firebox Enclosure Requirements
Do not install appliance until all necessary provisions are made
for combustion and ventilation air. Consult the written instructions
provided with the appliance for information concerning combustion
and ventilation air. In the absence of instructions, refer to the
National Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion
and Ventilation, or applicable local codes.
WARNING`
-
sion or other electrical appliance installed above it.
Installation must conform with one of the following conditions:
With walls on all sides, but with no overhead cover;
Within a partial enclosure which includes an overhead cover
and no more than two side walls. These side walls may be
parallel, as in a breezeway or at right angles to each side; or
Within a partial enclosure which includes an overhead cover
and three sidewalls, as long as 30% or more of the horizontal
periphery of the enclosures is permanently open.
appliance and/or accessory are rated for use up to 50,000 Btu
instructions that came with the appliance or accessory (i.e.
clearances, combustion and ventilation air, and enclosure
information).
WARNING
Improper installation, adjustment, alteration, service or mainte-
nance can cause property damage, personal injury or loss of life.
service agency or the gas supplier.
Clearances
Figure 4
where studs are to be placed.
Figure 5
PLANNING INSTALLATION
32273-0-0713Page 10
PLANNING INSTALLATION
Installing the Hood
Finishing
Hearth extensions are recommended, not a requirement for these
Figure 6
Cleaning Instructions
This appliance is built using mostly high-grade stainless steel to
resist rust-through. In outdoor applications, all stainless steel will
develop a dull patina and, depending on the local environment
and on the materials used in the installation, may develop some
surface oxidation (rust). This does not affect the performance of
-
-
quired with stainless steel cleaner.
When installation application includes highly acidic applications
such as mortar or stone etching, do not remove the protective PVC
-
ance be cleaned with a stainless steel cleaner immediately.
FIREBOX FRAMING AND INSTALLATION
Locate the three metal framing studs:
SIDE TOP
OP32FB Two - 42” Stud One - 36-5/8” Top Stud
OP36FB Two - 42” Stud One - 44-5/8” Top Stud
OP42FB Two - 42” Stud One - 45-5/8” Top Stud
1. Secure the metal studs to the frame using six #10 pan-head
screws as shown in Figure 7. The channel of the studs
should face as shown in Figure 7.
Figure 7
Note: If using a drain tray, verify framing height using the drain
tray.
the 1/2 inch non-combustible board provided with the unit.
Figure 8
3. Locate the middle bracket. Loosen the screw in the middle
shown in Figure 10. Tighten the hex-head screws on the
and into the top stud.
32273-0-0713 Page 11
7. Secure the non-combustible board to the middle bracket
Figure 11
Alternate Framing and Installation Method
the 1/2 inch non-combustible board provided with the unit.
2. Connect the side framing studs to the top stud as shown in
Figure 12. The channel of the studs should face inward.
Figure 12
head screws.
Note: If using a drain tray, the bottom of the side framing studs
4. Locate the middle bracket. Loosen the screw in the middle
shown in Figure 10. Tighten the hex-head screws on the
and into the top stud.
5. Locate the two non-combustible boards and place them
screws.
6. Secure the non-combustible board to the middle bracket
unit and check for leaks with a soapy water solution.
Note: Ensure that the gas shut-off valve is accessible.
as shown in Figure 9.
Figure 9
5. Connect the gas line to the unit and check for leaks with a
soapy water solution.
Note: Ensure that the gas shut-off valve is accessible.
6. Locate the two non-combustible boards and place them
screws.
Figure 10
FIREBOX FRAMING AND INSTALLATION
32273-0-0713Page 12
person in accordance with all building codes. Consult local building
codes to properly size the gas supply line leading to the 3/8-inch
hook-up at the unit. The state of Massachusetts requires that a
See
Figure 12. Carefully remove the knockout in the refractory brick
panel using a large standard screwdriver and hammer. First, place
screwdriver in groove next to plug and pry sideways to pop out
main plug. Then remove the remaining concrete in hole with gentle
tapping with ball peen hammer and/or screwdriver. A masonry drill
and bit may also be used to create a clean hole for the gas line to
pass through. See Figure 13.
screwdriver to punch out the metal knockout.
set rating plate. If the gas listed on the plate is not your type of gas
supply, DO NOT INSTALL. Contact your dealer for proper model.
supply tank pressure to a maximum of 14" w.c. This is in addition
Install only a ANSI Z21.97.1/CSA 2.41 ventless log set into this
Figure 12
GAS LINE CONNECTION
Figure 13
GAS ACCESS HOLES
32273-0-0713 Page 13
com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the
nature of the problem with the unit.
To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below.
This list changes from time to time. For the current list, please click on the Master Parts button at www.empirecomfort.com.
Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original
Equipment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc.
MASTER PARTS DISTRIBUTOR LIST
Parts Not Under Warranty
Parts can be ordered through your Service Person, Dealer, or a Master Parts Distributor. See this page for the Master Parts Distribu-
tors list. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the
service person/dealer.
Warranty Parts
Warranty parts will need a proof of purchase and can be ordered by your Service Person or Dealer. Proof of purchase is required for
warranty parts.
name plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the fol-
lowing illustration and part list. Be sure to give all this information . . .
Appliance Model Number Part Description
Appliance Serial Number Part Number
Type of Gas (Propane or Natural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
HOW TO ORDER REPAIR PARTS
Dey Distributing
1401 Willow Lake Boulevard
Vadnais Heights, MN 55101
Phone: 651-490-9191
Toll Free: 800-397-1339
Website: www.deydistributing.com
Victor Division of F. W. Webb Company
200 Locust Street
Hartford, CT 06114
Phone: 860-722-2433
Toll Free: 800-243-9360
Fax: 860-293-0479
Toll Free Fax: 800-274-2004
Websites: www.fwwebb.com & www.victormfg.com
East Coast Energy Products
10 East Route 36
West Long Branch, NJ 07764
Phone: 732-870-8809
Toll Free: 800-755-8809
Fax: 732-870-8811
Website: www.eastcoastenergy.com
Able Distributors
2501 North Central Avenue
Chicago, IL 60639
Phone: 773-889-5555
Toll Free: 800-880-2253
Fax: 773-466-1118
Website: www. abledistributors.com
Parts: Heater
32273-0-0713Page 14
PARTS LIST
Index
No.
PART No. Description
OP32FB2MF OP36FB2MF OP42FB2MF
1 23219 23219 23219 Top Standoff
2 28987 27781 27782 Firebox Front
3 32359 32359 32359 Mount Bracket
4 R10387 R10391 R10391 Liner, Side - Left
5 R10388 R10392 R10392 Liner, Side - Right
6 R10386 R10390 R10393 Liner, Rear
7 27792 27792 27792 Liner Bracket - Bottom
8 20447 20447 20447 Liner Bracket - Top
9 29068 20234 20237 Hood
10 R11107 R11036 R11037 Curtain, Rod
11 R11108 R10765 R10765 Curtain, Screen
12 R11104 R11105 R11106 Liner, Bottom
13 32231 32231 32231 Metal Channel - Side
14 32232 32233 32234 Metal Channel - Top
15 R11678 R11681 R11683 Non-Combustible Board
16 10554 10554 10554 Flange
USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INjURY OR DEATH.
32273-0-0713 Page 15
PARTS VIEW
32273-0-0713Page 16
WARRANTY TERMS
EMPIRE
EMPIRE
Comfort Systems
Empire Comfort Systems Inc.
918 Freeburg Ave. Belleville, IL 62220
If you have a general question about our products, please e-mail us at
If you have a service or repair question, please contact your dealer.
www.empirecomfort.com
Empire Comfort Systems Inc. warranties this hearth product to be free from defects at the time of purchase and for the pe-
Limited Five-Year Parts Warranty – All Components
(Except Remote Controls, Thermostats, Accessories and Replacement Parts)
Limited One-Year Parts Warranty – Remote Controls, Thermostats, Accessories, and Parts
Should any remote control, thermostat, accessory, or other part fail because of defective workmanship within one
Duties of the Owner
with the appliance.
A bill of sale, cancelled check, or payment record should be kept to verify purchase date and establish warranty
period.
Ready access to the appliance for service.
What Is Not Covered
Damages that might result from the use, misuse, or improper installation of this appliance.
Travel, diagnostic costs and freight charges on warranted parts to and from the factory.
Claims that do not involve defective workmanship or materials.
Removal and reinstallation cost.
Inoperable due to improper or lack of maintenance.
How To Get Service
To make a claim under this warranty, please have your receipt available and contact your installing dealer. Pro-
-
sponsible for providing service and will contact the factory to initiate any warranted parts replacements. Empire will make
replacement parts available at the factory. Shipping expenses are not covered.
If, after contacting your Empire dealer, service received has not been satisfactory, contact: Consumer Relations
Department, Empire Comfort Systems Inc., PO Box 529, Belleville, Illinois 62222, or send an e-mail to info@empirecom-
Your Rights Under State Law
This manual suits for next models
2
Table of contents
Other Empire Comfort Systems Indoor Fireplace manuals
Empire Comfort Systems
Empire Comfort Systems DVCT36CBP95N-2 Series Planning guide
Empire Comfort Systems
Empire Comfort Systems Boulevard VFLL60FP90LP-1 User manual
Empire Comfort Systems
Empire Comfort Systems CIBV-30-2 Quick start guide
Empire Comfort Systems
Empire Comfort Systems DVD32 Quick start guide
Empire Comfort Systems
Empire Comfort Systems Breckenridge VFFD-32-1 Quick start guide
Empire Comfort Systems
Empire Comfort Systems DVCT30CBN95N-2 User manual
Empire Comfort Systems
Empire Comfort Systems VFD26FM series User manual
Empire Comfort Systems
Empire Comfort Systems White Mountain Hearth VFP24FP20LN-1 Quick start guide
Empire Comfort Systems
Empire Comfort Systems DVP36PP32EN-4 User manual
Empire Comfort Systems
Empire Comfort Systems EF39 User manual
Empire Comfort Systems
Empire Comfort Systems DVD32FP33N-4 User manual
Empire Comfort Systems
Empire Comfort Systems VFH-33M-1 Quick start guide
Empire Comfort Systems
Empire Comfort Systems VFP32FB0F-5 Quick start guide
Empire Comfort Systems
Empire Comfort Systems MILLIVOLT DVCP3630-1 Quick start guide
Empire Comfort Systems
Empire Comfort Systems VFD26FM(2 Quick start guide
Empire Comfort Systems
Empire Comfort Systems VFLL38FP30L-1 Quick start guide
Empire Comfort Systems
Empire Comfort Systems VFP24FP30 Quick start guide
Empire Comfort Systems
Empire Comfort Systems DVCP32BP30N-4 User manual
Empire Comfort Systems
Empire Comfort Systems White Mountain Hearth DVTL27FP90N-1 Quick start guide
Empire Comfort Systems
Empire Comfort Systems HYDRAULIC Quick start guide
Empire Comfort Systems
Empire Comfort Systems superb CHBR-16-3 Quick start guide
Empire Comfort Systems
Empire Comfort Systems DVP42FP3(0 Quick start guide
Empire Comfort Systems
Empire Comfort Systems MILLIVOLT DVD32FP30N-3 User manual
Empire Comfort Systems
Empire Comfort Systems DVD32FP34N-2 User manual
Popular Indoor Fireplace manuals by other brands
Drolet
Drolet Eastwood 1800 DB03161 Installation and operation manual
Apex Fires
Apex Fires HAVANA Installation instructions & operating manual
HWAM
HWAM Autopilot IHS 7100 user manual
Bellfires
Bellfires Smart Bell 65 MF Preparation manual
Dimplex
Dimplex BLF5051-AU/PRISM 50" owner's manual
GDC Group
GDC Group BACH Instructions for use
Valor
Valor black beauty 466 owner's guide
ecofires
ecofires eko 2050 Installation & user's instructions
chazelles
chazelles GIGIO Installation and instruction manual
Faber
Faber e-MatriX 800-500 RD installation manual
Rinnai
Rinnai RF1200TW Operation & installation manual
Empire
Empire LTH1118-1 installation instructions
Whalen
Whalen WMFP48EC-18 manual
Valor
Valor BOLERO BR626 Installer's guide
EarthCore
EarthCore Isokern Maximus Linear 82L48 Installation, operation, maintenance and owner's manual
Heatilator
Heatilator GBI25 Series Installation & operating instructions
Nectre Fireplaces
Nectre Fireplaces Nectre 15 operating instructions
Twin-Star International
Twin-Star International home CFS-300-BLK instructions