Watch in amazement as two life-like jellyfish gently float and sway in the
water when you activate your switch. Just fill the tower with distilled
water, add the plastic jellyfish and a steady flow of air will circulate and
animate the jellyfish. Great for teaching cause and effect and for
encouraging visual attention. Size: 2¾"L x 2¾"W x 9"H. Requires 3 AA
Batteries. Weight: 2 lbs.
WARNING: Choking hazard. Small parts. Not for children under 3
WARNING: Choking hazard. Small parts. Not for children under 3 WARNING: Choking hazard. Small parts. Not for children under 3
WARNING: Choking hazard. Small parts. Not for children under 3
years.
years.years.
years.
Operation:
Operation:Operation:
Operation:
. Jelly Fish Lamp requires 3 AA batteries. The battery compartment is
located under the base of the unit. Carefully turn the unit over, and
remove the battery cover. Install new batteries, being careful to
observe proper battery polarity. Alkaline batteries must be used only
(e.g. Duracell or Energizer brand). Do not use rechargeable
batteries or any other type of batteries because they supply lower
voltage and the unit will not perform properly. Never mix old, new or
different types of batteries together. Replace the battery
compartment cover.
2. Lift off the black cover of the bottle and the rubber stopper at the
top of the bottle and fill the bottle with 75% tap or distilled water.
3. Please Note:
Please Note:Please Note:
Please Note: The Jelly Fish are extremely delicate. Handle very
carefully. Carefully and slowly place them into the bottle.
4. Fill the container the rest of the way with water and replace the
rubber stopper and black cover.
5. Next plug in your external capability switch into the female /8"
jack, located in the side of the unit. If your switch has a ¼" male
plug, then order one of our # 70 ¼" to /8" adapters. Make sure
the male plug is pressed firmly into the female jack, there should be
not gaps. Set the Jelly Ball Lamp’s ON/OFF
ON/OFFON/OFF
ON/OFF switch to OFF
OFFOFF
OFF
for
external switch use. You can now activate the Jelly Fish Lamp with
your switch.
6. When you activate your switch the Jelly Fish will float accompanied
by illuminating light. Once you release your switch the Jelly Fish with
sink and light will stop.
7. The Jelly Fish Lamp can be used normally without the use of a
switch.
Troubleshooting:
Troubleshooting:Troubleshooting:
Troubleshooting:
Problem:
Problem:Problem:
Problem: The Jelly Fish Lamp does not turn on when switch is
depressed.
Action # :
Action # :Action # :
Action # : Make sure that you press all connections firmly together.
Any gaps may interrupt electrical connection. The Jelly Fish Lamp’s
ON/OFF
ON/OFFON/OFF
ON/OFF switch needs to be set to O
OO
OFF
FFFF
FF
for external switch use.
Action #2:
Action #2:Action #2:
Action #2: Make sure batteries are fresh.
Action #3:
Action #3:Action #3:
Action #3: Try a different switch with your Jelly Fish Lamp to rule it out
as the source of the problem.
Notes:
Notes:Notes:
Notes:
• If the Jelly Fish Lamp is not used for an extended period, make
sure to remove the batteries and empty the water.
• This unit is intended for indoor use only.
Care of Unit:
Care of Unit:Care of Unit:
Care of Unit:
The Jelly Fish Lamp can be wiped clean with any mild household multi-
purpose, non-abrasive cleaner and disinfectant. We recommend Simple
Green, which is a non-toxic biodegradable all-purpose cleaner.
Do not submerge
Do not submergeDo not submerge
Do not submerge the unit in any fluids, as it will damage the contents
and the electrical components.
Do not use abrasive cleaners
Do not use abrasive cleanersDo not use abrasive cleaners
Do not use abrasive cleaners, as they will scratch the surface of the
unit.
Rev
Rev Rev
Rev 3/7/ 7
3/7/ 73/7/ 7
3/7/ 7
