Enclume DUTCH CROWN RACK PR2 Instruction manual

Enclume DUTCH CROWN RACK
PR2
Enclume racks are the ultimate in
Quality, design, strength and function.
Congratulations for owning one of the finest
Storage racks made.
WARNING:
READ ALL OF THE INSTRUCTIONS
BEFORE ASSEMBLING AND USING
YOUR RACK.
All of our hammered steel racks are finished with an industrial wax designed to
give years of protection to the rack. Cleaning is easily done with a damp cloth. Dry
thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge"
like wax product.
Enclosed you will find everything needed for the assembly
and use of your storage rack. Two people make assembly
and installation easier. The parts and hardware included are:
Hardware included:
4 –3/8” x ½” Button Head Screws
1 – Ceiling Screw Hook
1- 7/32” Allen Wrench
12 – Angled pot hooks
Toggler Kit
Components included:
1 – Hoop Body
4 – Arm
1 – Axial
1 – Grid
6 – Straight Pot Hooks
4 – Grid Brackets
See reverse side for ASSEMBLY AND INSTALLATION INSTRUCTIONS
Limited Warranty:This product is warranted to be free of material defects for a period of five years from the date of purchase. Customer's exclusive remedy shall
be the repair or replacement of the defective product and shall be subject to the following conditions: (1) notice of any defect is received by Enclume within the
warranty period and (2) customer returns the defective product to Enclume Design Products, Inc. , 24 Colwell St.. , Port Hadlock, WA 98339, postage prepaid
within 20 days following a return authorization number (which may be obtained by telephoning the number at the bottom of this instructions) being provided to the
customer by Enclume. There are no other warranties, expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. ENCLUME SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE PURCHASE OR USE OF ENCLUME'S PRODUCTS.

ASSEMBLY AND INSTALLATION INSTRUCTIONS for PR2
Enclosed you will find everything needed for the assembly
and use of your storage rack. Two people make assembly
and installation easier. The parts and hardware included are:
Hardware included:
4 – 3/8” x ½” Button Head Screws
1 – Ceiling Screw Hook
12 – Straight pot hooks
1 – 7/32” Allen wrench
Toggler Kit
Components included:
1 – Hoop Body
4 – Arm
1 – Axial
1 – Grid
6 – Straight Pot Hooks
4 – Grid Brackets
Rack Assembly
1) If your rack is plated it is best to keep the tissue on during installation to avoid fingerprinting.
2) Thread the axial through the roll at the top of each of the four arms.
3) Hold the axial and arms over the hoop body. Place the base of the arms over the outside of the hoop body. Attach the two
together with the ½” button head screws, leaving the screws loose.
4) Arrange the axial so that it is level and the arms are symmetrical.
5) Tighten the screws. The assembly of your rack is now complete.
6) We recommend that you anchor your rack into the solid wood of ceiling joists or beams. Carefully measure the area where the
rack is to be hung and install the ceiling screw hooks directly into the wood joists. If it is not convenient to hang your rack
directly into wood joists you may use the new-technology DRYWALL anchors enclosed with your rack. The steel anchors are
very strong and when installed in drywall will hold 200 lbs. each. Two anchors hold about 400 lbs. Follow the instructions in
the Toggler kit.
7) Distribute the weight of your cookware evenly around the hoop.
8) All of our hammered steel racks are finished with an industrial wax designed to give years of protection to the rack. Cleaning is
easily done with a damp cloth. Dry thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge" like wax
product.
9) The care and cleaning of our copper and brass units must be done with a low abrasive cleaner such as “Flitz”. Chrome racks are
best cleaned with a good quality glass cleaner like “Windex”. Our high quality plating will age & tarnish the same as solid
material. A periodic cleaning will restore your rack to its original brilliance.
Grid Assembly
1) Slip the grid brackets over the hoop, placing one near each hole where the arms will attach.. The “L” portion should point to the
inside of the circle.
2) Place the grid on the brackets and adjust it so that is rests evenly on all four brackets and doesn’t wobble.
3) Hang your pot hooks from the interior squares only Do not hang them from the perimeter or the cut portions of the grid.
Distribute your cookware evenly.
4) The grid has been treated with a finish which will resist corrosion and tarnish. It can be cleaned with a damp cloth and dried
thoroughly. Please do not use abrasive cleaners.
It is important that your rack is assembled correctly. If the unit is assembled or used incorrectly, it
could become unstable and collapse, possibly causing injury.
WARNING