Endress+Hauser Levelflex FMP51 User manual

Products Solutions Services
Operating Instructions
Levelflex FMP51, FMP52, FMP54
HART
Guided wave radar
BA01001F/00/EN/20.17
71385415
01.03.zz (Device firmware)

Levelflex FMP51, FMP52, FMP54 HART
2 Endress+Hauser
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser
Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
1.
3.
2.
A0023555

Levelflex FMP51, FMP52, FMP54 HART Table of contents
Endress+Hauser 3
Table of contents
1 Important document information .... 5
1.1 Document function ..................... 5
1.2 Symbols .............................. 5
1.2.1 Safety symbols .................. 5
1.2.2 Electrical symbols ................ 5
1.2.3 Tool symbols .................... 5
1.2.4 Symbols for
certain types of information ......... 6
1.2.5 Symbols in graphics ............... 6
1.2.6 Symbols at the device ............. 7
1.3 Supplementary documentation ............. 8
1.3.1 Safety Instructions (XA) ............ 9
2 Basic safety instructions ........... 13
2.1 Requirements for the personnel ........... 13
2.2 Designated use ....................... 13
2.3 Workplace safety ...................... 14
2.4 Operational safety ..................... 14
2.5 Product safety ........................ 14
2.5.1 CE mark ...................... 14
2.5.2 EAC conformity ................. 15
3 Product description ................ 16
3.1 Product design ........................ 16
3.1.1 Levelflex FMP51/FMP52/FMP54/
FMP55 ....................... 16
3.1.2 Electronics housing .............. 17
3.2 Registered trademarks .................. 18
4 Incoming acceptance and product
identification ..................... 19
4.1 Incoming acceptance ................... 19
4.2 Product identification .................. 19
4.2.1 Nameplate .................... 20
5 Storage, Transport ................ 21
5.1 Storage conditions ..................... 21
5.2 Transport product to the measuring point .... 21
6 Mounting ......................... 22
6.1 Mounting requirements ................. 22
6.1.1 Suitable mounting position ........ 22
6.1.2 Applications with restricted
mounting space ................. 24
6.1.3 Notes on the mechanical load of the
probe ........................ 26
6.1.4 Notes on the process connection .... 28
6.1.5 Mounting cladded flanges ......... 33
6.1.6 Securing the probe .............. 34
6.1.7 Special mounting conditions ....... 37
6.2 Mounting the device ................... 48
6.2.1 Required mounting tools .......... 48
6.2.2 Shortening the probe ............. 48
6.2.3 FMP54 with gas phase
compensation: Mounting the probe
rod .......................... 50
6.2.4 Mounting the device ............. 51
6.2.5 Mounting the "Sensor remote"
version ....................... 52
6.2.6 Turning the transmitter housing .... 54
6.2.7 Turning the display module ........ 54
6.3 Post-installation check .................. 55
7 Electrical connection .............. 56
7.1 Connection conditions .................. 56
7.1.1 Terminal assignment ............. 56
7.1.2 Cable specification ............... 62
7.1.3 Device plug connectors ........... 63
7.1.4 Power supply .................. 64
7.1.5 Overvoltage protection ........... 67
7.2 Connecting the measuring device .......... 67
7.2.1 Plug-in spring-force terminals ...... 68
7.3 Post-connection check .................. 69
8 Operation options ................. 70
8.1 Overview ............................ 70
8.1.1 Local operation ................. 70
8.1.2 Operation with remote display and
operating module FHX50 .......... 71
8.1.3 Remote operation ............... 71
8.2 Structure and function of the operating
menu .............................. 73
8.2.1 Structure of the operating menu .... 73
8.2.2 User roles and related access
authorization .................. 75
8.2.3 Write protection via access code ..... 76
8.2.4 Disabling write protection via access
code ......................... 77
8.2.5 Deactivation of the write protection
via access code ................. 77
8.2.6 Write protection via write protection
switch ........................ 77
8.2.7 Enabling and disabling the keypad
lock ......................... 80
8.3 Display and operating module ............ 81
8.3.1 Display appearance .............. 81
8.3.2 Operating elements .............. 84
8.3.3 Entering numbers and text ........ 85
8.3.4 Opening the context menu ......... 87
8.3.5 Envelope curve on the display and
operating module ............... 88

Table of contents Levelflex FMP51, FMP52, FMP54 HART
4 Endress+Hauser
9 Device integration via the HART
protocol .......................... 89
9.1 Overview of the Device Description files
(DD) ............................... 89
9.2 HART device variables and measuring
values .............................. 89
10 Commissioning via wizard ......... 90
11 Commissioning via operating
menu ............................. 91
11.1 Installation and function check ............ 91
11.2 Setting the operating language ............ 91
11.3 Checking the reference distance ........... 91
11.4 Configuration of a level measurement ...... 93
11.5 Configuration of an interface measurement .. 95
11.6 Recording the reference curve ............ 97
11.7 Configuration of the on-site display ........ 98
11.7.1 Factory settings of the on-site
display for level measurements ..... 98
11.7.2 Factory settings of the on-site
display for interface measurements .. 98
11.7.3 Adjustment of the on-site display ... 98
11.8 Configuration of the current outputs ........ 99
11.8.1 Factory setting of the current
outputs for level measurements ..... 99
11.8.2 Factory setting of the current
outputs for interface measurements .. 99
11.8.3 Adjustment of the current outputs ... 99
11.9 Configuration management ............. 100
11.10 Protection of the settings against
unauthorized changes ................. 101
12 Diagnostics and troubleshooting .. 102
12.1 General trouble shooting ............... 102
12.1.1 General errors ................. 102
12.1.2 Parametrization errors .......... 103
12.2 Diagnostic information on local display ..... 105
12.2.1 Diagnostic message ............. 105
12.2.2 Calling up remedial measures ..... 107
12.3 Diagnostic event in the operating tool ...... 108
12.4 Diagnostic list ....................... 109
12.5 List of diagnostic events ................ 110
12.6 Event logbook ....................... 112
12.6.1 Event history .................. 112
12.6.2 Filtering the event logbook ....... 112
12.6.3 Overview of information events .... 112
12.7 Firmware history ..................... 114
13 Maintenance .................... 115
13.1 Exterior cleaning ..................... 115
14 Repairs .......................... 116
14.1 General information on repairs ........... 116
14.1.1 Repair concept ................ 116
14.1.2 Repairs to Ex-approved devices .... 116
14.1.3 Replacement of an electronics
module ...................... 116
14.1.4 Replacement of a device ......... 116
14.2 Spare parts ......................... 117
14.3 Return ............................. 117
14.4 Disposal ........................... 117
15 Accessories ...................... 118
15.1 Device-specific accessories .............. 118
15.1.1 Weather protection cover ........ 118
15.1.2 Mounting bracket for the electronics
housing ..................... 119
15.1.3 Extension rod / centering HMP40 .. 120
15.1.4 Mounting kit, isolated ........... 121
15.1.5 Centering star ................. 122
15.1.6 Remote display FHX50 .......... 124
15.1.7 Overvoltage protection .......... 125
15.2 Communication-specific accessories ....... 126
15.3 Service-specific accessories .............. 127
15.4 System components ................... 128
16 Operating menu .................. 129
16.1 Overview of the operating menu (display
module) ........................... 129
16.2 Overview of the operating menu (operating
tool) .............................. 137
16.3 "Setup" menu ........................ 144
16.3.1 "Mapping" wizard ............... 157
16.3.2 "Advanced setup" submenu ........ 158
16.4 "Diagnostics" menu .................... 213
16.4.1 "Diagnostic list" submenu ......... 215
16.4.2 "Event logbook" submenu ......... 216
16.4.3 "Device information" submenu ..... 217
16.4.4 "Measured values" submenu ....... 220
16.4.5 "Data logging" submenu .......... 224
16.4.6 "Simulation" submenu ........... 227
16.4.7 "Device check" submenu .......... 232
16.4.8 "Heartbeat" submenu ............ 234
Index ................................. 235

Levelflex FMP51, FMP52, FMP54 HART Important document information
Endress+Hauser 5
1 Important document information
1.1 Document function
These Operating Instructions contain all the information that is required in various phases
of the life cycle of the device: from product identification, incoming acceptance and
storage, to mounting, connection, operation and commissioning through to
troubleshooting, maintenance and disposal.
1.2 Symbols
1.2.1 Safety symbols
Symbol Meaning
DANGER
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will
result in serious or fatal injury.
WARNING
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in serious or fatal injury.
CAUTION
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in minor or medium injury.
NOTICE
NOTE!
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.2.2 Electrical symbols
Symbol Meaning
Direct current
Alternating current
Direct current and alternating current
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a
grounding system.
Protective Earth (PE)
A terminal which must be connected to ground prior to establishing any other
connections.
The ground terminals are situated inside and outside the device:
• Inner ground terminal: Connects the protectiv earth to the mains supply.
• Outer ground terminal: Connects the device to the plant grounding system.
1.2.3 Tool symbols
Symbol Meaning
A0013442
Torx screwdriver
A0011220
Flat blade screwdriver

Important document information Levelflex FMP51, FMP52, FMP54 HART
6 Endress+Hauser
Symbol Meaning
A0011219
Cross-head screwdriver
A0011221
Allen key
A0011222
Hexagon wrench
1.2.4 Symbols for certain types of information
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Preferred
Procedures, processes or actions that are preferred.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information.
Reference to documentation.
A
Reference to page.
Reference to graphic.
Notice or individual step to be observed.
1.
,
2.
,
3.
… Series of steps.
Result of a step.
Help in the event of a problem.
Visual inspection.
1.2.5 Symbols in graphics
Symbol Meaning
1, 2, 3 ... Item numbers
1.
,
2.
,
3.
… Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
-
Hazardous area
Indicates a hazardous area.
.
Safe area (non-hazardous area)
Indicates the non-hazardous area.

Levelflex FMP51, FMP52, FMP54 HART Important document information
Endress+Hauser 7
1.2.6 Symbols at the device
Symbol Meaning
Safety instructions
Observe the safety instructions contained in the associated Operating Instructions.
Temperature resistance of the connection cables
Specifies the minimum value of the temperature resistance of the connection cables.

Important document information Levelflex FMP51, FMP52, FMP54 HART
8 Endress+Hauser
1.3 Supplementary documentation
Document Purpose and content of the document
Technical Information
TI01001F (FMP51, FMP52,
FMP54)
Planning aid for your device
The document contains all the technical data on the device and provides
an overview of the accessories and other products that can be ordered for
the device.
Brief Operating Instructions
KA01077F (FMP51/FMP52/
FMP54, HART)
Guide that takes you quickly to the 1st measured value
The Brief Operating Instructions contain all the essential information
from incoming acceptance to initial commissioning.
Description of Device Parameters
GP01000F (FMP5x, HART)
Reference for your parameters
The document provides a detailed explanation of each individual
parameter in the operating menu. The description is aimed at those who
work with the device over the entire life cycle and perform specific
configurations.
Special documentation
SD00326F
Functional Safety Manual
The document is part of the Operating Instructions and serves as a
reference for application-specific parameters and notes.
Special documentation
SD01872F
Manual for Heartbeat Verification and Heartbeat Monitoring
The document contains descriptions of the additonal parameters and
technical data which are available with the Heartbeat Verification and
Heartbeat Monitoring application packages.
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The W@M Device Viewer : Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate
or scan the 2-D matrix code (QR code) on the nameplate.

Levelflex FMP51, FMP52, FMP54 HART Important document information
Endress+Hauser 9
1.3.1 Safety Instructions (XA)
Depending on the approval, the following Safety Instructions (XA) are supplied with the
device. They are an integral part of the Operating Instructions.
Feature 010 Approval Available for Feature 020: "Power Supply; Output"
A 1) B 2) C 3) E 4)/G 5) K 6)/L 7)
BA ATEX II 1G Ex ia IIC T6 Ga • FMP51
• FMP52
• FMP54
XA00496F XA01125F XA01126F XA00516F -
BB ATEX II 1/2G Ex ia IIC T6 Ga/Gb • FMP51
• FMP52
• FMP54
XA00496F XA01125F XA01126F XA00516F -
BC ATEX II 1/2G Ex d[ia] IIC T6 Ga/Gb • FMP51
• FMP52
• FMP54
XA00499F XA00499F XA00499F XA00519F XA01133F
BD ATEX II 1/3G Ex ic[ia] IIC T6 Ga/Gc • FMP51
• FMP52
• FMP54
XA00497F XA01127F XA01128F XA00517F -
BE ATEX II 1D Ex t IIIC Da FMP54 XA00501F XA00501F XA00501F XA00521F XA00501F
BF ATEX II 1/2D Ex t IIIC Da/Db FMP54 XA00501F XA00501F XA00501F XA00521F XA00501F
BG ATEX II 3G Ex nA IIC T6 Gc • FMP51
• FMP52
• FMP54
XA00498F XA01130F XA01131F XA00518F XA01132F
BH ATEX II 3G Ex ic IIC T6 Gc • FMP51
• FMP52
• FMP54
XA00498F XA01130F XA01131F XA00518F -
BL ATEX II 1/3G Ex nA[ia] IIC T6 Ga/Gc • FMP51
• FMP52
• FMP54
XA00497F XA01127F XA01128F XA00517F XA01129F
B2 ATEX II 1/2G Ex ia IIC T6 Ga/Gb, 1/2D Ex ia IIIC Da/Db • FMP51
• FMP52
• FMP54
XA00502F XA00502F XA00502F XA00522F -
B3 ATEX II 1/2G Ex d[ia] IIC T6 Ga/Gb, 1/2 D Ex t IIIC
Da/Db
• FMP51
• FMP52
• FMP54
XA00503F XA00503F XA00503F XA00523F XA01136F
B4 ATEX II 1/2G Ex ia IIC T6 Ga/Gb, Ex d[ia] IIC T6 Ga/Gb • FMP51
• FMP52
• FMP54
XA00500F XA01134F XA01135F XA00520F -
CD CSA C/US DIP Cl.II,III Div.1 Gr.E-G FMP54 XA00529F XA00529F XA00529F XA00570F XA00529F
C2 CSA C/US IS Cl.I,II,III Div.1 Gr.A-G, NI Cl.1 Div.2, Ex ia • FMP51
• FMP52
• FMP54
XA00530F XA00530F XA00530F XA00571F XA00530F
C3 CSA C/US XP Cl.I,II,III Div.1 Gr.A-G, NI Cl.1 Div.2, Ex d • FMP51
• FMP52
• FMP54
XA00529F XA00529F XA00529F XA00570F XA00529F
FB FM IS Cl.I,II,III Div.1 Gr.A-G, AEx ia, NI Cl.1 Div.2 • FMP51
• FMP52
• FMP54
XA00531F XA00531F XA00531F XA00573F XA00531F
FD FM XP Cl.I,II,III Div.1 Gr.A-G, AEx d, NI Cl.1 Div.2 • FMP51
• FMP52
• FMP54
XA00532F XA00532F XA00532F XA00572F XA00532F
FE FM DIP Cl.II,III Div.1 Gr.E-G FMP54 XA00532F XA00532F XA00532F XA00572F XA00532F
GA EAC Ex ia IIC T6 Ga • FMP51
• FMP52
• FMP54
XA01380F XA01380F XA01380F XA01381F XA01380F

Important document information Levelflex FMP51, FMP52, FMP54 HART
10 Endress+Hauser
Feature 010 Approval Available for Feature 020: "Power Supply; Output"
A 1) B 2) C 3) E 4)/G 5) K 6)/L 7)
GB EAC Ex ia IIC T6 Ga/Gb • FMP51
• FMP52
• FMP54
XA01380F XA01380F XA01380F XA01381F XA01380F
GC EAC Ex d[ia] IIC T6 Ga/Gb • FMP51
• FMP52
• FMP54
XA01382F XA01382F XA01382F XA01383F XA01382F
IA IEC Ex ia IIC T6 Ga • FMP51
• FMP52
• FMP54
XA00496F XA01125F XA01126F XA00516F -
IB IEC Ex ia IIC T6 Ga/Gb • FMP51
• FMP52
• FMP54
XA00496F XA01125F XA01126F XA00516F -
IC IEC Ex d[ia] IIC T6 Ga/Gb • FMP51
• FMP52
• FMP54
XA00499F XA00499F XA00499F XA00519F XA01133F
ID IEC Ex ic[ia] IIC T6 Ga/Gc • FMP51
• FMP52
• FMP54
XA00497F XA01127F XA01128F XA00517F -
IE IEC Ex t IIIC Da FMP54 XA00501F XA00501F XA00501F XA00521F XA00501F
IF IEC Ex t IIIC Da/Db FMP54 XA00501F XA00501F XA00501F XA00521F XA00501F
IG IEC Ex nA IIC T6 Gc • FMP51
• FMP52
• FMP54
XA00498F XA01130F XA01131F XA00518F XA01132F
IH IEC Ex ic IIC T6 Gc • FMP51
• FMP52
• FMP54
XA00498F XA01130F XA01131F XA00518F -
IL IEC Ex nA[ia] IIC T6 Ga/Gc • FMP51
• FMP52
• FMP54
XA00497F XA01127F XA01128F XA00517F XA01129F
I2 IEC Ex ia IIC T6 Ga/Gb, Ex ia IIIC Da/Db • FMP51
• FMP52
• FMP54
XA00502F XA00502F XA00502F XA00522F -
I3 IEC Ex d [ia] IIC T6 Ga/Gb, Ex t IIIC Da/Db • FMP51
• FMP52
• FMP54
XA00503F XA00503F XA00503F XA00523F XA01136F
I4 IEC Ex II 1/2G Ex ia IIC T6 Ga/Gb, Ex d[ia] IIC T6 Ga/Gb • FMP51
• FMP52
• FMP54
XA00500F XA01134F XA01135F XA00520F -
KA KC Ex ia IIC T6 Ga • FMP51
• FMP52
• FMP54
XA01169F - XA01169F - -
KB KC Ex ia IIC T6 Ga/Gb • FMP51
• FMP52
• FMP54
XA01169F - XA01169F - -
KC KC Ex d[ia] IIC T6 • FMP51
• FMP52
• FMP54
- - XA01170F - -
MA INMETRO Ex ia IIC T6 Ga • FMP51
• FMP52
• FMP54
XA01038F XA01038F XA01038F - XA01038F
MC INMETRO Ex d[ia] IIC T6 Ga/Gb • FMP51
• FMP52
• FMP54
XA01041F XA01041F XA01041F - XA01041F
ME INMETRO Ex t IIIC Da FMP54 XA01043F XA01043F XA01043F - XA01043F