Endress+Hauser Proline Promag 50P Manual

TI047D/24/ae/07.06
Technical Information
Proline Promag 50P, 53P
Electromagnetic Flow Measuring System
Flow rate measurement in chemical or process applications
Application
Electromagnetic flowmeter for bidirectional
measurement of liquids with a minimum conductivity
of ≥ 5 µS/cm:
• Acids and caustic solutions
•Paints
•Pastes,mashes
• Water, wastewater etc.
• Flow measurement up to 44,000 GPM
(9600 m3/h)
• Fluid temperature up to 356°F (180°C)
• Process pressures up to 580 psi (40 bar)
• Fitting lengths to DVGW/ISO
Application-specific lining materials:
• PTFE und PFA
Approvals for hazardous area:
• ATEX, FM, CSA, TIIS
Connection to process control system:
•HART
®, Profibus®DP/PA, FOUNDATION™
Fieldbus, MODBUS®RS485
Your benefits
Promag measuring devices offer you cost-effective flow
measurement with a high degree of accuracy for a wide
range of process conditions.
The Proline transmitter concept comprises:
• Modular device and operating concept resulting in a
higher degree of efficiency
• Software options for batching, electrode cleaning and
for measuring pulsating flow.
• Uniform operating concept
The tried-and-tested Promag sensors offer:
•Nopressureloss
• Not sensitive to vibrations
• Simple installation and commissioning

Proline Promag 50P, 53P
2Endress+Hauser
Function and system design
Measuring principle Faraday’s law of induction states that a voltage is induced in a conductor moving in a magnetic field.
In electromagnetic measuring, the flowing medium corresponds to the moving conductor. The induced voltage
is proportional to the flow velocity and is detected by two measuring electrodes and transmitted to the ampli-
fier. Flow volume is computed on the basis of the pipe's diameter. The constant magnetic field is generated by
a switched direct current of alternating polarity.
A0003191
Ue = B · L · v
Q = A · v
Ue = induced voltage
B = magnetic induction (magnetic field)
L = electrode gap
v = flow velocity
Q = volume flow
A = pipe cross-section
I = current strength
Measuring system The measuring system consists of a transmitter and a sensor.
Two versions are available:
• Compact version: transmitter and sensor form a single mechanical unit.
• Remote version: transmitter and sensor are installed separately.
Transmitter:
The Promag 50/53 transmitters incorporate a high impedance amplifier of 1 x 1012 ohms or greater.
• Promag 50 (user interface with push buttons for operation, two-line display)
• Promag 53 (“Touch Control” without opening the housing, four-line display)
Sensor:
• 1/2" to 24" (DN 15 to 600)
Input
Measured variable Flow rate (proportional to induced voltage)
Measuring range Typically v = 0.033 to 33 ft/s (0.01 to 10 m/s) with the specified measuring accuracy
Operable flow range Over 1000 : 1
Input signal Status input (auxiliary input):
U = 3 to 30 V DC, Ri= 5 kΩ,galvanically isolated.
Configurable for: totalizer(s) reset, measured value suppression, error-message reset.
Status input (auxiliary input) with PROFIBUS DP and MODBUS RS485:
U = 3 to 30 V DC, Ri= 3 kΩ, galvanically isolated
Ue
I
I
B
L
V

Proline Promag 50P, 53P
Endress+Hauser 3
Switching level: 3 to 30 V DC, independent of polarity
Configurable for: totalizer(s) reset, measured value suppression, error-message reset,
batching start/stop (optional), batch totalizer reset (optional)
Current input (for Promag 53 only):
Active/passive selectable, galvanically isolated, full scale value selectable, resolution: 3 µA,
temperature coefficient: typ. 0.003% o.r./°F (0.005% o.r./°C), o.r. = of reading
active: 4 to 20 mA, Ri≤150 Ω, Uout = 24 V DC, short-circuit-proof
passive: 0/4 to 20 mA, Ri≤ 150 Ω, Umax = 30 V DC
Output
Output signal Promag 50
Current output:
active/passive selectable, galvanically isolated, time constant selectable (0.01 to 100 s),
full scale value selectable, temperature coefficient: typ. 0.003% o.r./°F (0.005% o.r./°C), o.r. = of reading,
resolution: 0.5 µA
• active: 0/4 to 20 mA, RL< 700 Ω(HART: RL≥250 Ω)
• passive: 4 to 20 mA, operating voltage VS18 to 30 V DC, Ri≤150 Ω
Pulse/frequency output:
passive, open collector, 30 V DC, 250 mA, galvanically isolated.
• Frequency output: full scale frequency 2 to 1000 Hz (fmax = 1250 Hz), on/off ratio 1:1,
pulse width max. 10 s.
• Pulse output: pulse value and pulse polarity selectable, max. pulse width configurable
(0.5 to 2000 ms)
PROFIBUS DP interface:
• Transmission technology (Physical Layer): RS485 in accordance with ANSI/TIA/EIA-485-A: 1998,
galvanically isolated
• Profile version 3.0
• Data transmission rate: 9.6 kBaud to 12 MBaud
• Automatic data transmission rate recognition
• Function blocks: 1 x analog input, 3 x totalizer
• Output data: volume flow, totalizer
• Input data: positive zero return (ON/OFF), totalizer control, value for local display
• Cyclic data transmission compatible with previous model “Promag 33”
• Bus address adjustable via miniature switches or local display (optional) at the measuring device

Proline Promag 50P, 53P
4Endress+Hauser
PROFIBUS PA interface:
• Transmission technology (Physical Layer): IEC 61158-2 (MBP), galvanically isolated
• Profile version 3.0
• Current consumption: 11 mA
• Permissible supply voltage: 9 to 32 V
• Bus connection with integrated reverse polarity protection
• Error current FDE (Fault Disconnection Electronic): 0 mA
• Function blocks: 1 x analog input, 1 x totalizer
• Output data: volume flow, totalizer
• Input data: positive zero return (ON/OFF), control totalizer, value for local display
• Cyclic data transmission compatible with previous model “Promag 33”
• Bus address adjustable via miniature switches or local display (optional) at the measuring device
Promag 53
Current output:
active/passive selectable, galvanically isolated, time constant selectable (0.01 to 100 s),
full scale value selectable, temperature coefficient: typically 0.005% o.r./°C (o.r. = of reading),
resolution: 0.5 µA
• active: 0/4 to 20 mA, RL< 700 Ω(HART: RL≥250 Ω)
• passive: 4 to 20 mA, operating voltage VS18 to 30 V DC, Ri≤150 Ω
Pulse/frequency output:
active/passive selectable, galvanically isolated (Ex i version: only passive)
• active: 24 V DC, 25 mA (max. 250 mA during 20 ms), RL> 100 Ω
• passive: open collector, 30 V DC, 250 mA
• Frequency output: full scale frequency 2 to 10000 Hz (fmax = 12500 Hz), EEx-ia: 2 to 5000 Hz;
on/off ratio 1:1; pulse width max. 10 s.
• Pulse output: pulse value and pulse polarity adjustable, pulse width configurable
(0.05 to 2000 ms)
PROFIBUS DP interface:
• Transmission technology (Physical Layer): RS485 in accordance with ANSI/TIA/EIA-485-A:
1998, galvanically isolated
• Profile version 3.0
• Data transmission rate: 9.6 kBaud to 12 MBaud
• Automatic data transmission rate recognition
• Function blocks: 2 x analog input, 3 x totalizer
• Output data: volume flow, calculated mass flow, totalizer 1 to 3
• Input data: positive zero return (ON/OFF), totalizer control, value for local display
• Cyclic data transmission compatible with previous model “Promag 33”
• Bus address adjustable via miniature switches or local display (optional) at the measuring device
• Available output combination → Page 7 ff.
PROFIBUS PA interface:
• Transmission technology (Physical Layer): IEC 61158-2 (MBP), galvanically isolated
• Profile version 3.0
• Current consumption: 11 mA
• Permissible supply voltage: 9 to 32 V
• Bus connection with integrated reverse polarity protection
• Error current FDE (Fault Disconnection Electronic): 0 mA
• Function blocks: 2 x analog input, 3 x totalizer
• Output data: volume flow, calculated mass flow, totalizer 1 to 3
• Input data: positive zero return (ON/OFF), totalizer control, value for local display
• Cyclic data transmission compatible with previous model “Promag 33”
• Bus address adjustable via miniature switches or local display (optional) at the measuring device

Proline Promag 50P, 53P
Endress+Hauser 5
MODBUS interface:
• Transmission technology (Physical Layer): RS485 in accordance with ANSI/TIA/EIA-485-A:
1998, galvanically isolated
• MODBUS device type: Slave
• Address range: 1 to 247
• Bus address adjustable via miniature switches or local display (optional) at the measuring device
• Supported MODBUS function codes: 03, 04, 06, 08, 16, 23
• Broadcast: supported with the function codes 06, 16, 23
• Transmission mode: RTU oder ASCII
• Supported baudrate: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 Baud
• Response time:
Direct data access = typically 25 to 50 ms
Auto-scan buffer (data range) = typically 3 to 5 ms
• Available output combination → Page 7 ff.
FOUNDATION Fieldbus interface:
• FOUNDATION Fieldbus H1
• Transmission technology (Physical Layer): IEC 61158-2 (MBP), galvanically isolated
• ITK version 4.01
• Current consumption: 12 mA
• Error current FDE (Fault Disconnection Electronic): 0 mA
• Bus connection with integrated reverse polarity protection
• Function blocks: 5 x analog input, 1 x discrete output, 1 x PID
• Output data: volume flow, calculated mass flow, temperature, totalizer 1 to 3
• Input data: positive zero return (ON/OFF), reset totalizer
• Link Master (LM) functionality is supported
Signal on alarm • Current output → failure response selectable (e.g. in accord. with NAMUR Recom. NE 43)
• Pulse/frequency output → failure response selectable
• Status output (Promag 50) → non-conductive by fault or power supply failure
• Relay output (Promag 53) → de-energized by fault or power supply failure
Load See “Output signal”
Switching output Status output (Promag 50, Promag 53):
Open collector, max. 30 V DC / 250 mA, galvanically isolated.
Configurable for: error messages, Empty Pipe Detection (EPD), flow direction, limit values.
Relay outputs (Promag 53):
Normally closed (NC or break) or normally open (NO or make) contacts available
(default: relay 1 = NO, relay 2 = NC)
max. 30 V / 0.5 A AC; 60 V / 0.1 A DC, galvanically isolated.
Configurable for: error messages, Empty Pipe Detection (EPD), flow direction, limit values, batching contacts.
Low flow cutoff Switch points for low flow cutoff are selectable
Galvanic isolation All circuits for inputs, outputs, and power supply are galvanically isolated from each other.

Proline Promag 50P, 53P
6Endress+Hauser
Power supply
Electrical connection
Measuring unit
a0002441
Cable cross section max. 16 AWG (2.5 mm2)
A View A (field housing)
B View B (stainless steel field housing)
C View C (wall-mount housing)
*) not changeable communication board
**) changeable communication board
a Cover of the connection compartment
b Cable for power supply: 85 to 260 V AC, 20 to 55 V AC,16 to 62 V DC
Terminal No. 1: L1 for AC, L+ for DC
Terminal No. 2: N for AC, L- for DC
c Ground terminal for protective conductor
d Signal cable: see Terminal assignment →Page 7 ff.
Fieldbus cable:
Terminal No. 26: DP (A) / PA (+) / FF (+) / MODBUS RS485 (A) / (PA, FF: with reverse polarity protection)
Terminal No. 27: DP (B) / PA (-) / FF (-) / MODBUS RS485 (B) / (PA, FF: with reverse polarity protection)
e Ground terminal for signal-cable shield / Fieldbus cable / RS485 line
f Service connector for connecting service interface FXA 193 (Fieldcheck, Tof Tool - Fieldtool Package)
g Signal cable: see Terminal assignment →Page 7 ff.
Cable for external termination (only for PROFIBUS DP with fixed assignment communication board):
Terminal No. 24: +5 V
Terminal No. 25: DGND
a
a
d
b
a
HART*
PROFIBUS DP**
FOUNDATION Fieldbus*
PROFIBUS PA*
MODBUS RS485**
27
25
23
21
2
1
26
24
22
20
L1 (L+)
N (L-)
–
–
–
+
+
+
PA(–)/FF(–)
27
25
23
21
2
1
26
24
22
20
L1 (L+)
N (L-)
–
–
–
+
+
+
A (RxD/TxD-N)
B (RxD/TxD-P)
PA(+)/FF(+)
d
c
e
b
–27
–25
–23
–21
+26
+24
+22
+20
N (L-) 2
L1 (L+)1
25
23
21
2
1
24
22
20
L1 (L+)
N (L-)
–
–
–
+
+
+
27
26
A (RxD/TxD-N)
B (RxD/TxD-P)
AB
C
g
d
b
g
d
c
e
b
d
c
e
b
g
d
c
e
b
g
PROFIBUS DP*
(d)
bd/(g)
f f
f f

Proline Promag 50P, 53P
Endress+Hauser 7
Terminal assignment, Promag 50
Terminal assignment, Promag 53
The inputs and outputs on the communication board can be either permanently assigned or variable, depending
on the version ordered (see table). Replacements for modules which are defective or which have to be replaced
can be ordered as accessories.
Terminal No. (inputs / outputs)
Order variant 20 (+) / 21 (–) 22 (+) / 23 (–) 24 (+) / 25 (–) 26 (+) / 27 (–)
50***-***********W−−−
Current output
HART
50***-***********A−−Frequency output Current output
HART
50***-***********DStatus input Status output Frequency output Current output
HART
50***-***********H–––
PROFIBUS PA
50***-***********J––
+5 V (external
termination)
PROFIBUS DP
50***-***********S––
Frequency output
Ex i, passive
Current output Ex i
active, HART
50***-***********T––
Frequency output
Ex i, passive
Current output Ex i
passive, HART
Ground connection, power supply →Page 6
Terminal No. (inputs / outputs)
Order variant 20 (+) / 21 (–) 22 (+) / 23 (–) 24 (+) / 25 (–) 26 (+) / 27 (–)
Fixed communication boards (fixed assignment)
53***-***********A−−Frequency output Current output
HART
53***-***********BRelay output 2 Relay output 1 Frequency output Current output
HART
53***-***********F–––
PROFIBUS PA
IS
53***-***********G–––
FOUNDATION
Fieldbus, IS
53***-***********H–––
PROFIBUS PA
53***-***********J–––
PROFIBUS DP
53***-***********K−−−
FOUNDATION
Fieldbus
53***-***********Q−−Status input MODBUS RS485
53***-***********S−−
Frequency output
IS
Current output IS
active, HART
53***-***********T−−
Frequency output
IS
Current output IS
passive, HART
Flexible communication boards
53***-***********CRelay output 2 Relay output 1 Frequency output Current output
HART
53***-***********DStatus input Relay output Frequency output Current output
HART
53***-***********LStatus input Relay output 2 Relay output 1 Current output
HART

Proline Promag 50P, 53P
8Endress+Hauser
Electrical connection remote
version
F06-5xFxxxxx-04-xx-xx-de-001
n.c. = isolated cable shields, not connected
Cable entry Power-supply and signal cables (inputs/outputs):
• Cable entry M20 x 1.5 (8 to 12 mm)
• Sensor cable entry for armoured cables M20 x 1.5 (9.5 to 16 mm)
• Threads for cable entries 1/2" NPT, G 1/2"
Connecting cable for remote version:
• Cable entry M20 x 1.5 (8 to 12 mm)
• Sensor cable entry for armoured cables M20 x 1.5 (9.5 to 16 mm)
• Threads for cable entries 1/2" NPT, G 1/2"
53***-***********MStatus input Frequency output Frequency output Current output
HART
53***-***********NCurrent output Frequency output Status input MODBUS RS485
53***-***********PCurrent output Frequency output Status input PROFIBUS DP
53***-***********VRelay output 2 Relay output 1 Status input PROFIBUS DP
53***-***********2Relay output Current output Frequency output Current output
HART
53***-***********4Current input Relay output Frequency output Current output
HART
53***-***********5Status input Current input Frequency output Current output
HART
53***-***********7Relay output 2 Relay output 1 Status input MODBUS RS485
Ground connection, power supply →Page 6
Terminal No. (inputs / outputs)
Order variant 20 (+) / 21 (–) 22 (+) / 23 (–) 24 (+) / 25 (–) 26 (+) / 27 (–)
65
5
7
7
84
4
37
37
36 42
42
41
41
2
1
brown
white
green
yellow
n.c. n.c.n.c.
S1 E1 E2 S2 GND ES
EPD
Coil circuit
Pipe
Electrode circuit
Meas. signal

Proline Promag 50P, 53P
Endress+Hauser 9
Cable specifications
remote version
Coil cable:
• 2 x 18 AWG (0.75 mm2) PVC cable with common, braided copper shield (Ø approx. 7 mm)
• Conductor resistance: ≤37 Ω/km
• Capacitance: core/core, shield grounded: ≤120 pF/m
• Permanent operating temperature: -4 to +180°F (–20 to +80°C)
• Cable cross-section: max. 16 AWG (2.5 mm2)
Signal cable:
• 3 x 20 AWG (0.38 mm2) PVC cable with common, braided copper shield (Ø approx. 0.28" / 7 mm) and
individually shielded cores
• With Empty Pipe Detection (EPD): 4 x 20 AWG (0.38 mm2) PVC cable with common, braided copper shield
(Ø approx. 0.28" / 7 mm) and individually shielded cores.
• Conductor resistance: ≤50 Ω/km
• Capacitance: core/shield: ≤420 pF/m
• Permanent operating temperature: -4 to +180°F (–20 to +80°C)
• Cable cross-section: max. 16 AWG (2.5 mm2)
A0003194
a = signal cable, b = coil current cable (cross-section: max. 16 AWG / 2.5 mm2)
1 = core, 2 = core insulation, 3 = core shield, 4 = core jacket, 5 = core strengthening,
6 = cable shield, 7 = outer jacket
Optionally, Endress+Hauser also supplies reinforced connecting cables with an additional, metal strenghtening
braid. We recommend such cables for the following cases:
• Cables laid underground
• Danger of rodent attack
• Device used with ingress protection NEMA 6P (IP 68)
Operation in zones of severe electrical interference:
The measuring device complies with the general safety requirements in accordance with EN 61010,
the EMC requirements of EN 61326/A1, and NAMUR recommendation NE 21.
Caution!
Grounding is by means of the ground terminals provided for that purpose inside the connection housing.
Keep the stripped and twisted lengths of cable shield to the terminals as short as possible.
1
2
3
4
5
6
7
ab

Proline Promag 50P, 53P
10 Endress+Hauser
Supply voltage 85 to 260 V AC, 45 to 65 Hz
20 to 55 V AC, 45 to 65 Hz
16 to 62 V DC
PROFIBUS PA and FOUNDATION Fieldbus
Non-hazardous: 9 to 32 V DC
Intrinsically safe: 9 to 24 V DC
Explosion proof: 9 to 32 V DC
Power consumption AC: <15 VA (including sensor)
DC: <15 W (including sensor)
Switch-on current:
• max. 13.5 A (< 50 ms) at 24 V DC
• max. 3 A (< 5 ms) at 260 V AC
Power supply failure Lasting min. 1 power cycle:
• EEPROM or T-DAT (Promag 53 only) retain the measuring system data in the event of a power supply failure
• S-DAT: exchangeable data storage chip which stores the data of the sensor (nominal diameter, serial number,
calibration factor, zero point, etc.)
Potential equalisation Standard case
Perfect measurement is only ensured when the medium and the sensor have the same electrical potential. Most
Promag sensors have a standard installed reference electrode which guarantees the required connection. This
usually means that additional potential matching measures are unnecessary.
Note!
For installation in metal pipes, it is advisable to connect the ground terminal of the transmitter housing to the
piping. Also, observe company-internal grounding guidelines.
A0004375
Caution!
For sensors without reference electrodes or without metal process terminals, carry out potential matching as
per the instructions for special cases described below. These special measures are particularly important when
standard grounding practice cannot be ensured or extremely strong matching currents are expected.