Endress+Hauser Levelflex M FMP41C User manual

BA276F/00/en/11.06
No. 52021033
Valid as of software version
V 01.04.00 (amplifier)
V 01.04.00 (communication)
Operating Instructions
Levelflex M FMP41C
Guided Level-Radar
HART/4...20 mA
6

Brief overview Levelflex M FMP41C with HART/4...20 mA
2Endress + Hauser
Brief overview
For quick and simple commissioning:
Safety Instructions →ä6
Explanation of the warning symbols
You can find special instructions at the appropriate position in the chapter in
question. The positions are indicated with the icons Warning #, Caution "and
Note !.
Æ
Installation →ä12
The steps for installing the device and installation conditions (e.g. dimensions)
can be found here.
Æ
Wiring →ä22
The device is virtually completely wired on delivery.
Æ
Display and Operating Elements →ä28
An overview of the position of the display and operating elements can be found
here.
Æ
Commissioning via Display VU331 →ä41
In the "Commissioning" section, you learn how to switch on the device and
check the functioning.
Æ
Commissioning via Operating Software ToF Tool →ä54
In the "Commissioning" section, you learn how to switch on the device and
check the functioning.
Additional information on the operation of the ToF Tool can be found in the
operating instructions BA224F/00.
Æ
Fault Tracking / Trouble Shooting →ä65
If faults occur during operation, use the checklist to localise the cause.
Here you can find measures you can take yourself to take remedial action
against the fault.
Æ
Index →ä89
You can find important terms and keywords on the individual sections here.
Use the keyword index to find quickly and efficiently the information you need.

Levelflex M FMP41C with HART/4...20 mA Brief overview
Endress + Hauser 3
Brief operating instructions
L00-FMP40xxx-19-00-00-en-012
!
Note!
This operating manual explains the installation and initial start-up for the level transmitter
measuring device. All functions that are required for a typical measuring task are taken into account
here.
In addition, the Levelflex M provides many other functions that are not included in this operating
manual, such as optimising the measuring point and converting the measured values.
An overview of all device functions can be found on →ä84.
An extensive description of all device functions can be found in BA245F – "Description of the
instrument functions" on the enclosed CD-ROM.
Operating Instructions can also be found on our homepage: www.endress.com
E
+
-
+
E
+
-
E
E
-
… …
… …
KA 189F/00/a2/11.05
52012501
52012501
100%
0%
F
E
UB
LN
D
L
Levelflex M - Brief operating instructions
input E
(see sketch)
input F
(see sketch) displayed
D and L are confirm
or specify
range
suggestion
000
measured value
Group
selection
00
basic setup
01
safety settings
09
display
04
linearisation
05
extended calibr.
0C
system
parameters
092
language
0A
diagnostics
0A0
present
error
002
tank
properties
004
process
cond.
005
empty
calibr.
006
full
calibr.
008
dist./
meas value
051
check
distance
003
medium
property
052
range of
mapping
053
start
mapping
008
dist./
meas value
- envel. curve
- substracted signal
- mapping
- single curve
- cyclic
= 100: unlocked
¹ 100: locked
09A
plot settings
09B
recording
curve
0A1
previous
error
0A4
unlock
parameter
(333 = reset customer parameters)
0A3
reset
min. level
threaded
connection
1½
(G 1
:
reference point of
measurement
¾or BSP
¾orG ½)
¾or1½NPT
03
length
adjustment
030
end of
probe
031
probe
length
032
probe
033
probe
length
034
determine
length
- unknown
- 1.4 … 1.6
- 1.6 … 1.9
- 1.9 … 2.5
-4…7
-2.5…4
->7
0E
envelope curve
Contrast: +or +
- standard
- aluminium tank
- plastic tank
- bypass/pipe
- coax-probe
- concrete
wall
- standard
- fast
change
- test: no filter
- slow
change
- free
- tie down
isolated
- tie down
gnd.
If shortened
please enter probe length here.
reference point of
measurement
F = measuring span
E = empty distance (= zero)
UB = upper blocking distance
LN = probe length
L = level
D = distance

Brief overview Levelflex M FMP41C with HART/4...20 mA
4Endress + Hauser

Levelflex M FMP41C with HART/4...20 mA Table of contents
Endress + Hauser 5
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . 6
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Installation, commissioning and operation . . . . . . . . 6
1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4 Notes on safety conventions and icons . . . . . . . . . . . 7
2 Identification . . . . . . . . . . . . . . . . . . . . 8
2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3 Certificates and approvals . . . . . . . . . . . . . . . . . . . 11
2.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . 11
3 Installation . . . . . . . . . . . . . . . . . . . . . 12
3.1 Incoming acceptance, transport, storage . . . . . . . . . 12
3.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . 13
3.3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.4 Turn housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.5 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 21
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 22
4.1 Quick wiring guide . . . . . . . . . . . . . . . . . . . . . . . . 22
4.2 Connecting the measuring unit . . . . . . . . . . . . . . . 24
4.3 Recommended connection . . . . . . . . . . . . . . . . . . 27
4.4 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 27
4.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 27
5 Operation . . . . . . . . . . . . . . . . . . . . . . 28
5.1 Quick operation guide . . . . . . . . . . . . . . . . . . . . . . 28
5.2 Display and operating elements . . . . . . . . . . . . . . . 30
5.3 Local operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.4 Display and acknowledging error messages . . . . . . 35
5.5 HART communication . . . . . . . . . . . . . . . . . . . . . . 36
6 Commissioning. . . . . . . . . . . . . . . . . . 38
6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
6.2 Switching on the measuring device . . . . . . . . . . . . 38
6.3 Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
6.4 Basic Setup with the VU331 . . . . . . . . . . . . . . . . . 41
6.5 Blocking distance . . . . . . . . . . . . . . . . . . . . . . . . . 49
6.6 Envelope curve with VU331 . . . . . . . . . . . . . . . . . 51
6.7 Function "envelope curve display" (0E3) . . . . . . . . 52
6.8 Basic Setup with the ToF Tool . . . . . . . . . . . . . . . . 54
7 Maintenance. . . . . . . . . . . . . . . . . . . . 60
8 Accessories. . . . . . . . . . . . . . . . . . . . . 61
9 Trouble-shooting . . . . . . . . . . . . . . . . 65
9.1 Trouble-shooting instructions . . . . . . . . . . . . . . . . 65
9.2 System error messages . . . . . . . . . . . . . . . . . . . . . . 66
9.3 Application errors . . . . . . . . . . . . . . . . . . . . . . . . . 68
9.4 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
9.5 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
9.6 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
9.7 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
9.8 Contact addresses of Endress+Hauser . . . . . . . . . . . 76
10 Technical data . . . . . . . . . . . . . . . . . . . 77
10.1 Additional technical data . . . . . . . . . . . . . . . . . . . . 77
11 Appendix. . . . . . . . . . . . . . . . . . . . . . . 84
11.1 Operating menu HART (Display modul), ToF Tool . 84
11.2 Description of functions . . . . . . . . . . . . . . . . . . . . . 86
11.3 Function and system design . . . . . . . . . . . . . . . . . . 86
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Safety instructions Levelflex M FMP41C with HART/4...20 mA
6Endress + Hauser
1 Safety instructions
1.1 Designated use
The Levelflex M FMP41C is a compact level transmitter for the continuous measurement of solids
and liquids, measuring prinziple: Guided Level Radar / TDR: Time Domain Reflectometry.
1.2 Installation, commissioning and operation
The Levelflex M has been designed to operate safely in accordance with current technical, safety
and EU standards. If installed incorrectly or used for applications for which it is not intended,
however, it is possible that application-related dangers may arise, e.g. product overflow due to
incorrect installation or calibration. For this reason, the instrument must be installed, connected,
operated and maintained according to the instructions in this manual: personnel must be authorised
and suitably qualified. The manual must have been read and understood, and the instructions
followed. Modifications and repairs to the device are permissible only when they are expressly
approved in the manual.
1.3 Operational safety
Hazardous areas
Measuring systems for use in hazardous environments are accompanied by separate "Ex
documentation", which is an integral part of this Operating Manual. Strict compliance with the
installation instructions and ratings as stated in this supplementary documentation is mandatory.
• Ensure that all personnel are suitably qualified.
• Observe the specifications in the certificate as well as national and local regulations.

Levelflex M FMP41C with HART/4...20 mA Safety instructions
Endress + Hauser 7
1.4 Notes on safety conventions and icons
In order to highlight safety-relevant or alternative operating procedures in the manual, the following
conventions have been used, each indicated by a corresponding symbol in the margin.
Safety conventions
#
Warning!
A warning highlights actions or procedures which, if not performed correctly, will lead to personal
injury, a safety hazard or destruction of the instrument
"
Caution!
Caution highlights actions or procedures which, if not performed correctly, may lead to personal
injury or incorrect functioning of the instrument
!
Note!
A note highlights actions or procedures which, if not performed correctly, may indirectly affect
operation or may lead to an instrument response which is not planned
Explosion protection
0
Device certified for use in explosion hazardous area
If the device has this symbol embossed on its name plate it can be installed in an explosion hazardous
area
-
Explosion hazardous area
Symbol used in drawings to indicate explosion hazardous areas. Devices located in and wiring
entering areas with the designation “explosion hazardous areas” must conform with the stated type
of protection.
.
Safe area (non-explosion hazardous area)
Symbol used in drawings to indicate, if necessary, non-explosion hazardous areas. Devices located in
safe areas still require a certificate if their outputs run into explosion hazardous areas
Electrical symbols
%
Direct voltage
A terminal to which or from which a direct current or voltage may be applied or supplied
&
Alternating voltage
A terminal to which or from which an alternating (sine-wave) current or voltage may be applied or
supplied
)
Grounded terminal
A grounded terminal, which as far as the operator is concerned, is already grounded by means of an
earth grounding system
*
Protective grounding (earth) terminal
A terminal which must be connected to earth ground prior to making any other connection to the
equipment
+
Equipotential connection (earth bonding)
A connection made to the plant grounding system which may be of type e.g. neutral star or
equipotential line according to national or company practice
Temperature resistance of the connection cables
States, that the connection cables must be resistant to a temperature of at least 85 °C.
t >85°C

Identification Levelflex M FMP41C with HART/4...20 mA
8Endress + Hauser
2 Identification
2.1 Device designation
2.1.1 Nameplate
The following technical data are given on the instrument nameplate:
L00-FMP4xxxx-18-00-00-en-001
Fig. 1: Information on the nameplate of the Levelflex M FMP41C (example)
2.1.2 Ordering structure
This overview does not mark options which are mutually exclusive.
Ordering structure Levelflex M FMP41C
Made in Germany
D-79689 Maulburg
Dat./Insp.:
Order Code:
IP68 / NEMA 6P
Ser.-No.:
4-wire
ENDRESS+HAUSER
t >85°C
TA > 70°C:
D01301-A
if modification
see sep. label
X= Patents
LEVELFLEX-M
90 …253 V AC 3,5VA
10,5 …32VDC 1W
16 …3 V DC 0,8W
Profibus PA
Foundation Fieldbus
LN= PN=
4…20 mA HART 2-wire
Order No
(see Order Information)
Communication
variant and
supply voltage
Serial number
Reference to additional
safety-relevant documentation
Designation according to Directive 94/9/EC
and designation of protection
10 Approval:
A Non-hazardous area
F Non-hazardous area, WHG
1 ATEX II 1/2G EEx ia IIC T6
Note safety instruction (XA) (electristatic charging)!
3 ATEX II 2G EEx em (ia) IIC T6
Note safety instruction (XA) (electristatic charging)!
5 ATEX II 1/2G EEx ia IIC T6, ATEX II 1/3D
Note safety instruction (XA) (electristatic charging)!
6 ATEX II 1/2G EEx ia IIC T6, WHG
Note safety instruction (XA) (electristatic charging)!
7 ATEX II 1/2G EEx d (ia) IIC T6
Note safety instruction (XA) (electristatic charging)!
8 ATEX II 1/2G EEx ia IIC T6, ATEX II 1/3D, WHG
Note safety instruction (XA) (electristatic charging)!
G ATEX II 3G EEx nA II T6
S FM IS Cl.I,II,III Div.1 Gr.A-G N.I.
T FM XP Cl.I,II,III Div.1 Gr.A-G
N CSA General Purpose
U CSA IS Cl.I,II,III Div.1 Gr.A-D,G + coal dust, N.I.
V CSA XP Cl.I,II,III Div.1 Gr.A-D,G + coal dust, N.I.
K TIIS Ex ia IIC T4
L TIIS Ex d (ia) IIC T4
YSpecialversion
FMP41C- Product designation (part 1)

Levelflex M FMP41C with HART/4...20 mA Identification
Endress + Hauser 9
Ordering structure Levelflex M FMP41C (continued)
20 Probe:
A ..... mm, rope PFA>316, 150mm, Center rod, nozzle height max 150mm
B ..... mm, rope PFA>316, 300mm, Center rod, nozzle height max 300mm
C ..... mm, rope PFA>316, 450mm, Center rod, nozzle height max 450mm
D ..... inch, rope PFA>316, 6inch, Center rod, nozzle height max 6inch
E ..... inch, rope PFA>316, 12inch, Center rod, nozzle height max 12inch
G ..... inch, rope PFA>316, 18inch, Center rod, nozzle height max 18inch
K ..... mm, rod PFA>316L
M ..... inch, rod PFA>316L
Y Special version
30 Process Connection:
AEK 1-1/2" 150lbs, PTFE >316/316L flange ASME B16.5
AFK 2" 150lbs, PTFE >316/316L flange ASME B16.5
AGK 3" 150lbs, PTFE >316/316L flange ASME B16.5
AHK 4" 150lbs, PTFE >316/316L flange ASME B16.5
AJK 6" 150lbs, PTFE >316/316L flange ASME B16.5
AQK 1-1/2" 300lbs, PTFE >316/316L flange ASME B16.5
ARK 2" 300lbs, PTFE >316/316L flange ASME B16.5
ASK 3" 300lbs, PTFE >316/316L flange ASME B16.5
ATK 4" 300lbs, PTFE >316/316L flange ASME B16.5
CEK DN40 PN16-40, PTFE >316L flange EN1092-1 (DIN2527 C)
CFK DN50 PN10-40, PTFE >316L flange EN1092-1 (DIN2527 C)
CGK DN80 PN10/16, PTFE >316L flange EN1092-1 (DIN2527 C)
CHK DN100 PN10/16, PTFE >316L flange EN1092-1 (DIN2527 C)
CJK DN150 PN10/16, PTFE >316L flange EN1092-1 (DIN2527 C)
CSK DN80 PN25/40, PTFE >316L flange EN1092-1 (DIN2527 C)
CTK DN100 PN25/40, PTFE >316L flange EN1092-1 (DIN2527 C)
KEK 10K 40, PTFE >316L flange JIS B2220
KFK 10K 50, PTFE >316L flange JIS B2220
KGK 10K 80, PTFE >316L flange JIS B2220
KHK 10K 100, PTFE >316L flange JIS B2220
30 Process Connection:
MRK DIN11851 DN50 PN40, PTFE >316L
TCK Clamp ISO2852 1-1/2", PTFE >316L
TDK Clamp ISO2852 2", PTFE >316L
TFK Clamp ISO2852 3", PTFE >316L
TJK Clamp ISO2852 1-1/2", PTFE >316L
TKK DRD 65mm PN40, PTFE >316L
TLK Clamp ISO2852 2", PTFE >316L, 3A EHEDG
TNK Clamp ISO2852 3", PTFE >316L, 3A EHEDG
UPK Universal adapter 44mm, PTFE >316L
UQK Universal adapter 44mm, PTFE >316L, EHEDG 3A
YY9 Special version
FMP41C- Product designation (part 2)

Identification Levelflex M FMP41C with HART/4...20 mA
10 Endress + Hauser
Ordering structure Levelflex M FMP41C (continued)
40 Power Supply; Output:
B 2-wire; 4…20mA HART
D 2-wire; PROFIBUS PA
F 2-wire; FOUNDATION Fieldbus
G 4-wire 90...250VAC; 4...20mA HART
H 4-wire 10.5...32VDC; 4...20mA HART
Y Special version
50 Operation:
1 W/o display, via communication
2 4-line display VU331, Envelope curve display on site
3 Prepared for FHX40, Remote display (accessory)
9 Special version
60 Type of Probe:
1 Compact, basic version
3 Remote, cable 3m, top entry
4 Remote, cable 3m, side entry
9Specialversion
70 Housing:
A F12 Alu, coated IP68 NEMA6P
B F23 316L IP68 NEMA6P
C T12 Alu, coated IP68 NEMA6P, Separate conn. compartment
D T12 Alu, coated IP68 NEMA6P + OVP, Separate conn. compartment,
OVP = overvoltage protection
YSpecialversion
80 Cable Entry:
2 Gland M20 (EEx d > thread M20)
3ThreadG1/2
4ThreadNPT1/2
5PlugM12
6Plug7/8"
9Specialversion
90 Additional Option:
A Basic version
Y Special version
FMP41C- Complete product designation
⇓
Please enter probe length in mm or inch / 0.1 inch
mm
inch / 0.1 inch
probe length LN →ä14