Endress+Hauser Liquiline To Go CYM290 User manual

Operating Instructions
Liquiline To Go CYM290
Products ServicesSolutions

3
Basics
Warranty
Defects occurring within 3 years from delivery date shall be remedied free of charge
at our plant (carriage and insurance paid by sender).
Subject to change.
Return of Products Under Warranty
Please contact our Service Team before returning a defective device.
Ship the cleaned device to the address you have been given.
If the device has been in contact with process uids, it must be decontaminated/
disinfected before shipment. In that case, please attach a corresponding certicate,
for the health and safety of our service personnel.
Disposal
Please observe the applicable local or national regulations concerning
the disposal of “waste electrical and electronic equipment”.
Registered Trademarks
The following names are registered trademarks. For practical reasons they are shown
without trademark symbol in this manual.
• Memosens®
• Liquiline®
• Sensocheck®
• Sensoface®

4Table of Contents
Basics ..............................................................................................................................3
Table of Contents .......................................................................................................4
Package Contents ............................................................................... 6
Documentation................................................................................... 7
Overview ............................................................................................. 8
Value-Added Features ..............................................................................................9
Protective Cover.......................................................................................................10
Hook ............................................................................................................................10
Display and Keypad................................................................................................ 11
Start-Up.............................................................................................12
Inserting the Batteries ...........................................................................................12
Connecting a Sensor..............................................................................................13
Switching On the Meter........................................................................................14
Icons ............................................................................................................................14
Information.......................................................................................15
Calibration Record ..................................................................................................15
Sensor Information (Digital Sensors only)...................................................... 15
Sensor Network Diagram (pH and Oxy only) ................................................16
Sensor Monitor......................................................................................................... 17
Messages....................................................................................................................17
MemoLog (Memosens only) ...............................................................................17
Device Info.................................................................................................................18
Device Test.................................................................................................................18
Conguration ...................................................................................19
Calibration ................................................................................................................26
Manual Calibration .................................................................................................27
Data Entry Calibration ...........................................................................................27
Auto Calibration.......................................................................................................28
”Entry of Solution” Calibration ...........................................................................29
Cell Constant Calibration......................................................................................29
Calibration in Air...................................................................................................... 30

5
Table of Contents
Zero Calibration .......................................................................................................31
Data Entry Calibration ...........................................................................................31
Measuring .........................................................................................32
Toggling the Measured Value Display .............................................................32
Adjusting the Temperature..................................................................................32
Data Logger ......................................................................................33
Operating Modes of the Data Logger (Logger Type) ................................. 34
Conguring the Data Logger..............................................................................36
Increasing the Battery Life ...................................................................................36
Starting/Stopping the Data Logger..................................................................38
Viewing the Logger Data......................................................................................38
Deleting the Logger Data.....................................................................................38
Error and Status Messages...............................................................41
Info and Help Texts ................................................................................................. 42
Error Messages .........................................................................................................43
pH Product Line ................................................................................44
pH Sensors.................................................................................................................44
Endress+Hauser Buer Solutions (pH) ...........................................................45
Ready-to-use quality pH buer solutions.......................................................45
Accessories for pH................................................................................................... 45
Conductivity Product Line ...............................................................46
Conductivity Sensors .............................................................................................46
Conductivity Calibration Solutions CLY11...................................................... 47
Accessories for Conductivity............................................................................... 47
Oxygen Product Line........................................................................ 48
Oxygen Sensor .........................................................................................................48
Accessories for Oxygen......................................................................................... 48
Specications....................................................................................49
Index..................................................................................................55

6Package Contents
Check the shipment for transport damage and completeness.
The package of the Liquiline To Go CYM290 includes:
Liquiline To Go CYM290
Meter incl. 4 batteries (AA)
and premounted quiver P
Carrying strap P
Data carrier with detailed user manuals P
USB cable, 1.5 m P
Safety instructions P
Quickstart instructions in various languages P

7
Documentation
CD-ROM
Complete documentation:
• User manuals in dierent languages
• Safety instructions
• Certicates
• Quickstart guides
Safety Instructions
Quickstart Guides
Installation and rst steps:
• Operation
• Menu structure
• Calibration
• Error messages and recommended actions
Various languages on CD-ROM:
• German
• English
• French
• Italian
• Spanish
• Portuguese (Brazil)
Specic Test Report
CAUTION!
These safety instructions are part of the
product documentation and must be
observed.
In ocial EU languages and others.
• EU Declarations of Conformity

8
The Liquiline To Go CYM290 is a portable
multiparameter meter for use with analog
or digital sensors. The meter automatically
recognizes a connected Memosens sensor
and accordingly selects the correspond-
ing process variable. By simply replacing
the Memosens sensor, the meter can be
used for measuring conductivity, pH or
oxygen.
Operation is simple and intuitive, support-
ed by detailed information and help texts.
Overview
The meter stands out by the following features:
• Use of digital Memosens sensors
• A detachable quiver protects the sensor and prevents it from drying out.
Furthermore, it can be used for calibration.
• The rugged housing is made of a high-performance polymer. It provides high
impact resistance and dimensional stability even when exposed to extreme
moisture.
• Scratch-proof clear glass display, perfectly readable even after years
• Long operating time with one set of batteries (4 x AA) or use of a Li-ion battery for
reliable operation even at high or very low operating temperatures
• Data logger with 10,000 values
• Micro USB port
• Sensoface icons provide single-glance information on the sensor condition
• Real-time clock and indication of battery charging level
• Automatic compensation of ambient pressure for oxygen measurement
• At measuring temperatures from -20 to +100 °C the temperature detector can be
automatically identied.
Quiver

9
Value-Added Features
Memosens
The Liquiline To Go CYM290 can communicate
with Memosens sensors. These digital sensors are
automatically identied and the meter switches to
the appropriate measurement method.
When a Memosens sensor is connected to the
meter, it is indicated by the logo shown on the
right. Furthermore, Memosens allows the storage
of calibration data, which will be available and
can still be used when the sensor is connected to
another Memosens-capable device.
Sensoface
Sensoface provides quick information on the
sensor condition. The three“smiley” faces as shown
on the right represent the sensor condition during
measurement and after a calibration. When the
condition deteriorates, a status message gives a
hint to the cause.
Programmed buers
“Programmed buers” is a very convenient method
for pH calibration with automatic buer recogni-
tion. You only have to select the buer set with the
buers used. The buers can then be used in any
order.
Overview

10 Overview
Protective Cover
The front of the meter is protected
by a cover, which can be completely
ipped over and secured to the back for
operation.
Hook
A fold-out hook on the back allows
suspending the meter. This leaves your
hands free for the actual measurement.
The rating plate is located beneath the
hook.
Protective Cover and Hook
Combined
Cover and hook can be joined together
to form a benchtop stand allowing com-
fortable and fatigue-free working at a lab
bench or desk.