Endress+Hauser Proline Cubemass C 500 Manual

Ultra‐compact sensor for smallest quantities, with
a transmitter remote version with up to 4 I/Os
Application
• Measuring principle operates independently of physical fluid
properties such as viscosity or density
• Measuring accurately smallest quantities of liquids and
gases
Device properties
•Nominal diameter: DN 1 to 6 (¹⁄₂₄ to ¹⁄₄")
• Process pressure up to 400 bar (5 800 psi)
• Medium temperature up to +205 °C (+401 °F)
• Remote version with up to 4 I/Os
• Backlit display with touch control and WLAN access
• Standard cable between sensor and transmitter
Your benefits
• Reduced Installation cost – compact single-tube design
• Fewer process measuring points – multivariable
measurement (flow, density, temperature)
•Space‐saving installation – no inlet/outlet run needs
• Full access to process and diagnostic information –
numerous, freely combinable I/Os and fieldbuses
• Reduced complexity and variety – freely configurable I/O
functionality
• Integrated verification – Heartbeat Technology
Products Solutions Services
Technical Information
Proline Cubemass C 500
Coriolis flowmeter
TI01281D/06/EN/03.18
71402594
2018-06-01
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
2 Endress+Hauser
Table of contents
About this document ........................ 4
Symbols used ................................ 4
Function and system design ................... 5
Measuring principle ............................ 5
Measuring system ............................. 7
Equipment architecture ......................... 9
Safety ..................................... 9
Input .................................... 12
Measured variable ............................ 12
Measuring range ............................. 12
Operable flow range ........................... 12
Input signal ................................ 13
Output .................................. 15
Output and input variants ....................... 15
Output signal ............................... 16
Signal on alarm .............................. 20
Ex connection data ........................... 22
Low flow cut off ............................. 23
Galvanic isolation ............................ 23
Protocol-specific data .......................... 23
Power supply ............................. 28
Terminal assignment .......................... 28
Device plugs available .......................... 29
Pin assignment, device plug ...................... 30
Supply voltage .............................. 31
Power consumption ........................... 32
Current consumption .......................... 32
Power supply failure .......................... 32
Electrical connection .......................... 33
Potential equalization ......................... 43
terminals .................................. 44
Cable entries ............................... 44
Cable specification ............................ 44
Performance characteristics .................. 49
Reference operating conditions ................... 49
Maximum measured error ....................... 49
Repeatability ............................... 50
Response time .............................. 50
Influence of ambient temperature ................. 51
Influence of medium temperature .................. 51
Influence of medium pressure .................... 51
Design fundamentals .......................... 52
Installation ............................... 52
Mounting location ............................ 52
Orientation ................................ 53
Inlet and outlet runs .......................... 54
Mounting the transmitter housing ................. 55
Special mounting instructions .................... 56
Environment .............................. 59
Ambient temperature range ..................... 59
Storage temperature .......................... 59
Climate class ............................... 59
Degree of protection .......................... 60
Vibration resistance ........................... 60
Shock resistance ............................. 60
Shock resistance ............................. 60
Interior cleaning ............................. 60
Electromagnetic compatibility (EMC) ............... 60
Process .................................. 60
Medium temperature range ...................... 60
Density ................................... 61
Pressure-temperature ratings .................... 61
Sensor housing .............................. 63
Rupture disk ................................ 64
Flow limit ................................. 64
Pressure loss ............................... 64
System pressure ............................. 64
Thermal insulation ........................... 64
Heating ................................... 65
Vibrations ................................. 65
Mechanical construction .................... 66
Dimensions in SI units ......................... 66
Dimensions in US units ......................... 75
Weight ................................... 83
Materials .................................. 83
Process connections ........................... 86
Surface roughness ........................... 86
Operability ............................... 86
Operating concept ............................ 86
Languages ................................. 87
Local operation .............................. 87
Remote operation ............................ 87
Service interface ............................. 93
Network integration .......................... 94
Supported operating tools ....................... 95
HistoROM data management ..................... 96
Certificates and approvals ................... 98
CE mark ................................... 98
C-Tick symbol ............................... 98
Ex approval ................................ 98
Pharmaceutical compatibility .................... 100
Functional safety ............................ 100
HART certification ........................... 101
FOUNDATION Fieldbus certification ............... 101
Certification PROFIBUS ........................ 101
EtherNet/IP certification ....................... 101
Certification PROFINET ........................ 101
Radio approval ............................. 101
Additional certification ........................ 101
Other standards and guidelines .................. 102
Ordering information ...................... 102
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
Endress+Hauser 3
Application packages ...................... 102
Diagnostics functions ......................... 103
Heartbeat Technology ........................ 103
Concentration .............................. 103
Special density ............................. 103
OPC-UA server ............................. 103
Accessories .............................. 104
Device-specific accessories ...................... 104
Communication-specific accessories ............... 105
Service-specific accessories ..................... 106
System components .......................... 106
Supplementary documentation .............. 107
Standard documentation ....................... 107
Device-dependent additional documentation ......... 107
Registered trademarks ..................... 108
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
4 Endress+Hauser
About this document
Symbols used Electrical symbols
Symbol Meaning
Direct current
Alternating current
Direct current and alternating current
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a
grounding system.
Protective Earth (PE)
A terminal which must be connected to ground prior to establishing any other
connections.
The ground terminals are situated inside and outside the device:
• Inner ground terminal: Connects the protectiv earth to the mains supply.
• Outer ground terminal: Connects the device to the plant grounding system.
Communication symbols
Symbol Meaning
Wireless Local Area Network (WLAN)
Communication via a wireless, local network.
LED
Light emitting diode is off.
LED
Light emitting diode is on.
LED
Light emitting diode is flashing.
Symbols for certain types of information
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Preferred
Procedures, processes or actions that are preferred.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information.
Reference to documentation.
A
Reference to page.
Reference to graphic.
Visual inspection.
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
Endress+Hauser 5
Symbols in graphics
Symbol Meaning
1, 2, 3, ... Item numbers
1.
,
2.
,
3.
, … Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
-
Hazardous area
.
Safe area (non-hazardous area)
Flow direction
Function and system design
Measuring principle The measuring principle is based on the controlled generation of Coriolis forces. These forces are
always present in a system when both translational and rotational movements are superimposed.
Fc = 2 · ∆m (ν · ω)
Fc = Coriolis force
∆m = moving mass
ω = rotational velocity
ν = radial velocity in rotating or oscillating system
The amplitude of the Coriolis force depends on the moving mass ∆m, its velocity ν in the system and
thus on the mass flow. Instead of a constant rotational velocity ω, the sensor uses oscillation.
In the sensor, an oscillation is produced in the measuring tube. The Coriolis forces produced at the
measuring tube loop cause a phase shift in the tube oscillations (see illustration):
• If there is zero flow (i.e. when the fluid stands still), the oscillation measured at points A and B has
the same phase (no phase difference) (1).
•Mass flow causes deceleration of the oscillation at the inlet of the tubes (2) and acceleration at the
outlet (3).
2
13
A0029932
The phase difference (A-B) increases with increasing mass flow. Electrodynamic sensors register the
tube oscillations at the inlet and outlet. System balance is ensured by the antiphase oscillation of the
two measuring tubes. The measuring principle operates independently of temperature, pressure,
viscosity, conductivity and flow profile.
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
6 Endress+Hauser
Density measurement
The measuring tube is continuously excited at its resonance frequency. A change in the mass and
thus the density of the oscillating system (comprising measuring tube and fluid) results in a
corresponding, automatic adjustment in the oscillation frequency. Resonance frequency is thus a
function of medium density. The microprocessor utilizes this relationship to obtain a density signal.
Volume measurement
Together with the measured mass flow, this is used to calculate the volume flow.
Temperature measurement
The temperature of the measuring tube is determined in order to calculate the compensation factor
due to temperature effects. This signal corresponds to the process temperature and is also available
as an output signal.
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
Endress+Hauser 7
Measuring system The measuring system consists of a transmitter and a sensor. The transmitter and sensor are
mounted in physically separate locations. They are interconnected by connecting cables.
Transmitter
Two versions of the transmitter are available.
Proline 500 – digital Proline 500
For use in applications not required to meet special requirements due to
ambient or operating conditions.
For use in applications required to meet special requirements due to
ambient or operating conditions.
2
3
1
A
B
A Non-hazardous area or Zone 2; Class I, Division 2
B Non-hazardous area or Zone 2; Class I, Division 2 or Zone 1; Class I,
Division 1
1 Transmitter
2 Connecting cable: cable, separate, standard
3 Sensor connection housing with integrated ISEM
1
2
3
Non-hazardous area or Zone 2; Class I, Division 2 or Zone 1; Class I,
Division 1
1 Transmitter with integrated ISEM
2 Connecting cable: cable, separate
3 Sensor connection housing
• Flexible and cost-effective separate installation.
• A standard cable can be used as the connecting cable.
Application examples for sensors without electronics:
• Strong vibrations at the sensor.
• Sensor in underground installations.
•Permanent immersion of sensor in water, IP68 ingress protection.
• Electronics in the transmitter housing, ISEM (intelligent sensor
electronics module) in the sensor connection housing
• Signal transmission: digital
Order code for "Integrated ISEM electronics", option A "Sensor"
• Electronics and ISEM (intelligent sensor electronics module) in the
transmitter housing
• Signal transmission: analog
Order code for "Integrated ISEM electronics", option B "Transmitter"
Connecting cable (can be ordered in various lengths)→  104
• Length:
– Zone 2; Class I, Division 2: max. 300 m (1 000 ft)
– Zone 1; Class I, Division 1: max. 150 m (500 ft)
• Standard cable with common shield (pair-stranded)
• Length: max. 20 m (65 ft)
• Cable with a common shield and individual shielded cores (3 pairs)
Hazardous area
Use in: Zone 2; Class I, Division 2
Mixed installation is possible:
• Sensor: Zone 1; Class I, Division 1
• Transmitter: Zone 2; Class I, Division 2
Use in: Zone 1; Class I, Division 1 oder Zone 2; Class I, Division 2
Device versions and materials
• Transmitter housing
– Aluminum, coated: aluminum, AlSi10Mg, coated
– Material: polycarbonate
• Material of window in transmitter housing
– Aluminum, coated: glass
– Polycarbonate: plastic
• Transmitter housing
– Aluminum, coated: aluminum, AlSi10Mg, coated
– Cast, stainless: cast, stainless steel, 1.4409 (CF3M) similar to 316L
• Window material: glass
Configuration
• External operation via 4-line, backlit, graphic local display with touch control and guided menus ("Make-it-run" wizards) for application-specific
commissioning.
• Via service interface or WLAN interface:
– Operating tools (e.g. FieldCare, DeviceCare, SmartBlue app)
–Web server (access via Web browser, e.g. Microsoft Internet Explorer, Microsoft Edge)
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
8 Endress+Hauser
Sensor connection housing
Different versions of the connection housing are available.
Order code for "Sensor connection housing", option A, "Aluminum, coated":
Aluminum, AlSi10Mg, coated
This device version is only available in conjunction with the Proline
500 – digital transmitter.
Order code for "Sensor connection housing", option B, "Stainless":
• Hygienic version, stainless steel 1.4301 (304)
• Optional: order code for "Sensor feature", option CC "Hygienic version,
for maximum corrosion resistance": stainless steel 1.4404 (316L)
Order code for "Sensor connection housing", option C, "Ultra-compact
hygienic, stainless":
• Hygienic version, stainless steel 1.4301 (304)
• Optional: order code for "Sensor feature", option CC "Hygienic version,
for maximum corrosion resistance": stainless steel 1.4404 (316L)
This device version is only available in conjunction with the Proline
500 – digital transmitter.
Order code for "Sensor connection housing", option L, "Cast, stainless":
1.4409 (CF3M) similar to 316L
Sensor
Cubemass C
A0029825
The ultra compact single-tube system for minimum flow rates and high
pressure
•Simultaneous measurement of flow, volume flow, density and
temperature (multivariable)
•Immune to process influences
•Nominal diameter range: DN 1 to 6 (¹⁄₂₄ to ¹⁄₄ ")
• Materials:
– Sensor: stainless steel, 1.4301 (304)
– Measuring tube: stainless steel, 1.4539 (904L)
– Process connections: stainless steel, 1.4404 (316/316L); 1.4539
(904L)
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
Endress+Hauser 9
Equipment architecture
2
1
6
5
7
4
3
3
A0027512
 1 Possibilities for integrating measuring devices into a system
1Control system (e.g. PLC)
2 Connecting cable (0/4 to 20 mA HART etc.)
3 Fieldbus
4 Segment coupler
5 Non-hazardous area
6 Hazardous area: Zone 2; Class I, Division 2
7 Hazardous area: Zone 1; Class I, Division 1
Safety IT security
Our warranty is valid only if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any inadvertent
changes to the settings.
IT security measures, which provide additional protection for the device and associated data transfer,
must be implemented by the operators themselves in line with their security standards.
Device-specific IT security
The device offers a range of specific functions to support protective measures on the operator's side.
These functions can be configured by the user and guarantee greater in-operation safety if used
correctly. An overview of the most important functions is provided in the following section.
Function/interface Factory setting Recommendation
Write protection via hardware write
protection switch →  10
Not enabled. On an individual basis following risk
assessment.
Access code
(also applies for Web server login or
FieldCare connection) →  10
Not enabled
(0000).
Assign a customized access code during
commissioning.
WLAN
(order option in display module)
Enabled. On an individual basis following risk
assessment.
WLAN security mode Enabled (WPA2-
PSK)
Do not change.
WLAN passphrase
(password) →  10
Serial number Assign a customized access code during
commissioning.
WLAN mode Access Point On an individual basis following risk
assessment.
Web server→  10 Enabled. On an individual basis following risk
assessment.
CDI-RJ45 service interface →  11 – On an individual basis following risk
assessment.
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
10 Endress+Hauser
Protecting access via hardware write protection
Write access to the device parameters via the local display, Web browser or operating tool (e.g.
FieldCare, DeviceCare) can be disabled via a write protection switch (DIP switch on the
motherboard). When hardware write protection is enabled, only read access to the parameters is
possible.
Hardware write protection is disabled when the device is delivered.
Protecting access via a password
Different passwords are available to protect write access to the device parameters or access to the
device via the WLAN interface.
• User-specific access code
Protect write access to the device parameters via the local display, Web browser or operating tool
(e.g. FieldCare, DeviceCare). Access authorization is clearly regulated through the use of a user-
specific access code.
• WLAN passphrase
The network key protects a connection between an operating unit (e.g. notebook or tablet) and the
device via the WLAN interface which can be ordered as an option.
• Infrastructure mode
When the device is operated in infrastructure mode, the WLAN passphrase corresponds to the
WLAN passphrase configured on the operator side.
User-specific access code
Write access to the device parameters via the local display, Web browser or operating tool (e.g.
FieldCare, DeviceCare) can be protected by the modifiable, user-specific access code.
WLAN passphrase: Operation as WLAN access point
A connection between an operating unit (e.g. notebook or tablet) and the device via the WLAN
interface, which can be ordered as an optional extra, is protected by the network key. The WLAN
authentication of the network key complies with the IEEE 802.11 standard.
When the device is delivered, the network key is pre-defined depending on the device. It can be
changed via the WLAN settings submenu in the WLAN passphrase parameter.
Infrastructure mode
A connection between the device and WLAN access point is protected by means of an SSID and
passphrase on the system side. Please contact the relevant system administrator for access.
General notes on the use of passwords
• The access code and network key supplied with the device should be changed during
commissioning.
• Follow the general rules for generating a secure password when defining and managing the access
code or network key.
• The user is responsible for the management and careful handling of the access code and network
key.
Access via Web server
The device can be operated and configured via a Web browser with the integrated Web server. The
connection is via the service interface (CDI-RJ45) or the WLAN interface. For device versions with
the EtherNet/IP and PROFINET communication protocols, the connection can also be established via
the terminal connection for signal transmission with EtherNet/IP or PROFINET (RJ45 connector).
The Web server is enabled when the device is delivered. The Web server can be disabled if necessary
(e.g. after commissioning) via the Web server functionality parameter.
The device and status information can be hidden on the login page. This prevents unauthorized
access to the information.
For detailed information on device parameters, see:
The "Description of Device Parameters" document →  107
Access via OPC-UA
The "OPC UA Server" application package is available in the device version with the HART
communication protocol →  103.
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
Endress+Hauser 11
The device can communicate with OPC UA clients using the "OPC UA Server" application package.
The OPC UA server integrated in the device can be accessed via the WLAN access point using the
WLAN interface - which can be ordered as an optional extra - or the service interface (CDI- RJ45) via
Ethernet network. Access rights and authorization as per separate configuration.
The following Security Modes are supported as per the OPC UA Specification (IEC 62541):
• None
• Basic128Rsa15 – signed
•Basic128Rsa15 – signed and encrypted
Access via service interface (CDI-RJ45)
The device can be connected to a network via the service interface (CDI-RJ45). Device-specific
functions guarantee the secure operation of the device in a network.
The use of relevant industrial standards and guidelines that have been defined by national and
international safety committees, such as IEC/ISA62443 or the IEEE, is recommended. This includes
organizational security measures such as the assignment of access authorization as well as technical
measures such as network segmentation.
The device can be integrated in a ring topology. The device is integrated via the terminal
connection for signal transmission (output 1) and the connection to the service interface (CDI-
RJ45) →  91.
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
12 Endress+Hauser
Input
Measured variable Direct measured variables
• Mass flow
•Density
• Temperature
Calculated measured variables
• Volume flow
• Corrected volume flow
• Reference density
Measuring range Measuring ranges for liquids
DN Measuring range full scale values min(F) to max(F)
[mm] [in] [kg/h] [lb/min]
1 ¹⁄₂₄ 0 to 20 0 to 0.735
2 ¹⁄₁₂ 0 to 100 0 to 3.675
4 ¹⁄₈ 0 to 450 0 to 16.54
6 ¹⁄₄ 0 to 1 000 0 to 36.75
Measuring range for gases
The full scale value depends on the density and the sound velocity of the gas used and can be
calculated with the formula below:
max(G) = minimum (max(F) · ρG : x ; ρG · cG · π/2 · (di)2 · 3600)
 max(G) Maximum full scale value for gas [kg/h]
 max(F) Maximum full scale value for liquid [kg/h]
 max(G) <  max(F)  max(G) can never be greater than  max(F)
ρGGas density in [kg/m³] at operating conditions
xConstant dependent on nominal diameter
cGSound velocity (gas) [m/s]
diMeasuring tube internal diameter [m]
DN x
[mm] [in] [kg/m3]
1 ¹⁄₂₄ 20
2 ¹⁄₁₂ 20
4 ¹⁄₈ 20
6 ¹⁄₄ 20
To calculate the measuring range, use the Applicator sizing tool →  106
Recommended measuring range
"Flow limit" section →  64
Operable flow range Over 1000 : 1.
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
Endress+Hauser 13
Flow rates above the preset full scale value do not override the electronics unit, with the result that
the totalizer values are registered correctly.
Input signal Input and output versions
→  15
External measured values
To increase the accuracy of certain measured variables or to calculate the corrected volume flow for
gases, the automation system can continuously write different measured values to the measuring
device:
•Operating pressure to increase accuracy (Endress+Hauser recommends the use of a pressure
measuring device for absolute pressure, e.g. Cerabar M or Cerabar S)
• Medium temperature to increase accuracy (e.g. iTEMP)
• Reference density for calculating the corrected volume flow for gases
Various pressure transmitters and temperature measuring devices can be ordered from Endress
+Hauser: see "Accessories" section →  106
It is recommended to read in external measured values to calculate the corrected volume flow.
HART protocol
The measured values are written from the automation system to the measuring device via the HART
protocol. The pressure transmitter must support the following protocol-specific functions:
•HART protocol
• Burst mode
Current input
The measured values are written from the automation system to the measuring device via the
current input →  13.
Digital communication
The measured values can be written from the automation system to the measuring via:
• FOUNDATION Fieldbus
• PROFIBUS DP
• PROFIBUS PA
• Modbus RS485
• EtherNet/IP
• PROFINET
Current input 0/4 to 20 mA
Current input 0/4 to 20 mA (active/passive)
Current span • 4 to 20 mA (active)
• 0/4 to 20 mA (passive)
Resolution 1 µA
Voltage drop Typically: 0.6 to 2 V for 3.6 to 22 mA (passive)
Maximum input voltage ≤ 30 V (passive)
Open-circuit voltage ≤ 28.8 V (active)
Possible input variables • Pressure
• Temperature
• Density
Status input
Maximum input values • DC –3 to 30 V
• If status input is active (ON): Ri >3 kΩ
Response time Adjustable: 5 to 200 ms
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
14 Endress+Hauser
Input signal level • Low signal: DC –3 to +5 V
• High signal: DC 12 to 30 V
Assignable functions • Off
• Reset the individual totalizers separately
• Reset all totalizers
• Flow override
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
Endress+Hauser 15
Output
Output and input variants Depending on the option selected for output/input 1, different options are available for the other
outputs and inputs. Only one option can be selected for each output/input 1 to 4. The table must be
read vertically (↓).
Example: If the option BA "4–20 mA HART" was selected for output/input 1, one of the options A, B,
D, E, F, H, I or J is available for output 2, and one of the options A, B, D, E, F, H, I or J is available for
output 3 and 4.
Order code for "Output; input 1" (020) → Possible options
Current output 4 to 20 mA HART BA
Current output 4 to 20 mA HART Ex i ↓ CA
FOUNDATION Fieldbus ↓ SA
FOUNDATION Fieldbus Ex i ↓ TA
PROFIBUS DP ↓ LA
PROFIBUS PA ↓ GA
PROFIBUS PA Ex i ↓ HA
Modbus RS485 ↓ MA
EtherNet/IP 2-port switch integrated ↓ NA
PROFINET 2-port switch integrated ↓ RA
Order code for "Output; input 2" (021) → ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓
Not assigned A A A A A A A A A A
Current output 0/4 to 20 mA B B B B B B B
Current output 0/4 to 20 mA (Ex i) C C C
User configurable input/output 1) D D D D D D D
Pulse/frequency/switch output E E E E E E E
Double pulse output 2) F F
Pulse/frequency/switch output (Ex i) G G G
Relay output HH H H H H H
Current input 0/4 to 20 mA I I I I I I I
Status input J J J J J J J
Order code for "Output; input 3" (022), "Output; input 4" (023) 3) → ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓
Not assigned A A A A A A A A A A
Current output 0/4 to 20 mA B B B B B
Current output 0/4 to 20 mA (Ex i) C
User configurable input/output D D D D D
Pulse/frequency/switch output E E E E E
Double pulse output (slave) 4) F F
Pulse/frequency/switch output (Ex i) G
Relay output H H H H H
Current input 0/4 to 20 mA I I I I I
Status input J J J J J
1) A specific input or output can be assigned to a user configurable input/output →  19.
2) If double pulse output (F) is selected for output/input 2 (021), only the double pulse output (F) option is available for selection for output/input 3
(022).
3) The order code for "Output; input 4" (023) is only available for the Proline 500 – digital transmitter.
4) The double pulse output (F) option is not available for input/output 4.
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
16 Endress+Hauser
Output signal HART current output
Current output 4 to 20 mA HART
Current span Can be set to: 4 to 20 mA (active/passive)
Ex-i, passive
Open-circuit voltage DC 28.8 V (active)
Maximum input voltage DC 30 V (passive)
Load 250 to 700 Ω
Resolution 0.38 µA
Damping Configurable: 0.07 to 999 s
Assignable measured
variables
• Mass flow
• Volume flow
• Corrected volume flow
•Density
• Reference density
• Temperature
• Electronic temperature
• Oscillation frequency 0
• Oscillation damping 0
• Signal asymmetry
• Exciter current 0
The range of options increases if the measuring device has one or more
application packages.
PROFIBUS PA
PROFIBUS PA In accordance with EN 50170 Volume 2, IEC 61158-2 (MBP), galvanically
isolated
Data transmission 31.25 kbit/s
Current consumption 10 mA
16 mA
Permitted supply voltage 9 to 32 V
Bus connection With integrated reverse polarity protection
PROFIBUS DP
Signal encoding NRZ code
Data transfer 9.6 kBaud…12 MBaud
EtherNet/IP
Standards In accordance with IEEE 802.3
PROFINET
Standards In accordance with IEEE 802.3
FOUNDATION Fieldbus
FOUNDATION Fieldbus H1, IEC 61158-2, galvanically isolated
Data transfer 31.25 kbit/s
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
Endress+Hauser 17
Current consumption 10 mA
Permitted supply voltage 9 to 32 V
Bus connection With integrated reverse polarity protection
Modbus RS485
Physical interface RS485 in accordance with EIA/TIA-485 standard
Terminating resistor Integrated, can be activated via DIP switches
Current output 0/4 to 20 mA
Current output 0/4 to 20 mA
Maximum output values 22.5 mA
Current span Can be set to:
• 4 to 20 mA (active)
• 0/4 to 20 mA (passive)
Ex-i, passive
Open-circuit voltage DC 28.8 V (active)
Maximum input voltage DC 30 V (passive)
Load 0 to 700 Ω
Resolution 0.38 µA
Damping Adjustable: 0.07 to 999 s
Assignable measured
variables
• Mass flow
• Volume flow
• Corrected volume flow
• Density
• Reference density
• Temperature
• Electronic temperature
• Oscillation frequency 0
• Oscillation damping 0
• Signal asymmetry
• Exciter current 0
The range of options increases if the measuring device has one or more
application packages.
Pulse/frequency/switch output
Function Can be set to pulse, frequency or switch output
Version Open collector
Can be set to:
• Active
• Passive
Ex-i, passive
Maximum input values DC 30 V, 250 mA (passive)
Open-circuit voltage DC 28.8 V (active)
Voltage drop For 22.5 mA: ≤ DC 2 V
Pulse output
Maximum input values DC 30 V, 250 mA (passive)
Maximum output current 22.5 mA (active)
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
18 Endress+Hauser
Open-circuit voltage DC 28.8 V (active)
Pulse width Adjustable: 0.05 to 2 000 ms
Maximum pulse rate 10 000 Impulse/s
Pulse value Adjustable
Assignable measured
variables
• Mass flow
• Volume flow
• Corrected volume flow
Frequency output
Maximum input values DC 30 V, 250 mA (passive)
Maximum output current 22.5 mA (active)
Open-circuit voltage DC 28.8 V (active)
Output frequency Adjustable: end value frequency 2 to 10 000 Hz (f max = 12 500 Hz)
Damping Adjustable: 0 to 999 s
Pulse/pause ratio 1:1
Assignable measured
variables
• Mass flow
• Volume flow
• Corrected volume flow
• Density
• Reference density
• Temperature
• Electronic temperature
• Oscillation frequency 0
• Oscillation damping 0
• Signal asymmetry
• Exciter current 0
The range of options increases if the measuring device has one or more
application packages.
Switch output
Maximum input values DC 30 V, 250 mA (passive)
Open-circuit voltage DC 28.8 V (active)
Switching behavior Binary, conductive or non-conductive
Switching delay Adjustable: 0 to 100 s
Number of switching
cycles
Unlimited
Assignable functions • Off
• On
• Diagnostic behavior
• Limit value
– Mass flow
– Volume flow
– Corrected volume flow
– Density
– Reference density
– Temperature
– Totalizer 1-3
• Flow direction monitoring
• Status
– Partially filled pipe detection
– Low flow
The range of options increases if the measuring device has one or more
application packages.
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
Endress+Hauser 19
Double pulse output
Function Double pulse
Version Open collector
Can be set to:
• Active
• Passive
Maximum input values DC 30 V, 250 mA (passive)
Open-circuit voltage DC 28.8 V (active)
Voltage drop For 22.5 mA: ≤ DC 2 V
Output frequency Adjustable: 0 to 1 000 Hz
Damping Adjustable: 0 to 999 s
Pulse/pause ratio 1:1
Assignable measured
variables
• Mass flow
• Volume flow
• Corrected volume flow
• Density
• Reference density
• Temperature
The range of options increases if the measuring device has one or more
application packages.
Relay output
Function Switch output
Version Relay output, galvanically isolated
Switching behavior Can be set to:
• NO (normally open), factory setting
• NC (normally closed)
Maximum switching
capacity (passive)
•DC 30 V, 0.1 A
• AC 30 V, 0.5 A
Assignable functions • Off
• On
• Diagnostic behavior
• Limit value
– Mass flow
– Volume flow
– Corrected volume flow
– Density
– Reference density
– Temperature
– Totalizer 1-3
• Flow direction monitoring
• Status
– Partially filled pipe detection
– Low flow
The range of options increases if the measuring device has one or more
application packages.
User configurable input/output
One specific input or output is assigned to a user-configurable input/output (configurable I/O)
during device commissioning.
The following inputs and outputs are available for assignment:
• Choice of current output: 4 to 20 mA (active), 0/4 to 20 mA (passive)
•Pulse/frequency/switch output
• Choice of current input: 4 to 20 mA (active), 0/4 to 20 mA (passive)
• Status input
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]

Proline Cubemass C 500
20 Endress+Hauser
The technical values correspond to those of the inputs and outputs described in this section.
Signal on alarm Depending on the interface, failure information is displayed as follows:
HART current output
Device diagnostics Device condition can be read out via HART Command 48
PROFIBUS PA
Status and alarm
messages
Diagnostics in accordance with PROFIBUS PA Profile 3.02
Error current FDE (Fault
Disconnection Electronic)
0 mA
PROFIBUS DP
Status and alarm
messages
Diagnostics in accordance with PROFIBUS PA Profile 3.02
EtherNet/IP
Device diagnostics Device condition can be read out in Input Assembly
PROFINET
Device diagnostics According to "Application Layer protocol for decentralized periphery", Version 2.3
FOUNDATION Fieldbus
Status and alarm
messages
Diagnostics in accordance with FF-891
Error current FDE (Fault
Disconnection Electronic)
0 mA
Modbus RS485
Failure mode Choose from:
• NaN value instead of current value
• Last valid value
Current output 0/4 to 20 mA
4 to 20 mA
Failure mode Choose from:
• 4 to 20 mA in accordance with NAMUR recommendation NE 43
•4 to 20 mA in accordance with US
• Min. value: 3.59 mA
• Max. value: 22.5 mA
• Freely definable value between: 3.59 to 22.5 mA
• Actual value
• Last valid value
Заказывайте на сайте: www.tinnova.ru/endress_hauser/ || Эл. почта: [email protected]