Endress+Hauser Proline Promass E 200 Manual

The genuine loop-powered flowmeter for minimized cost of ownership
Application
• Measuring principle operates independently of physical fluid
properties such as viscosity or density
• Highly accurate measurement of liquids and gases for a wide
range of standard applications
Device properties
• Compact dual-tube system
• Medium temperature up to +140 °C (+284 °F)
• Process pressure up to 100 bar (1 450 psi)
• Loop-powered technology
• Robust two-chamber housing
• Plant safety: worldwide approvals (SIL, Haz. area)
Your benefits
• Cost-effective – multi-purpose device; an alternative to
conventional volumetric flowmeters
• Fewer process measuring points – multivariable
measurement (flow, density, temperature)
• Space-saving installation – no in/outlet run needs
• Convenient device wiring – separate connection
compartment
• Safe operation – no need to open the device due to display
with touch control, background lighting
• Integrated verification – Heartbeat Technology™
Products Solutions Services
Technical Information
Proline Promass E 200
Coriolis flowmeter
TI01009D/06/EN/17.14
71237197

Proline Promass E 200
2 Endress+Hauser
Table of contents
Document information ....................... 3
Symbols used ................................ 3
Function and system design ................... 4
Measuring principle ............................ 4
Measuring system ............................. 5
Input ..................................... 5
Measured variable ............................. 5
Measuring range .............................. 5
Operable flow range ........................... 6
Input signal ................................. 6
Output ................................... 7
Output signal ................................ 7
Signal on alarm ............................... 8
Load ...................................... 9
Ex connection data ........................... 10
Low flow cut off ............................. 12
Galvanic isolation ............................ 12
Protocol-specific data .......................... 12
Power supply ............................. 14
Terminal assignment .......................... 14
Pin assignment, device plug ...................... 14
Supply voltage .............................. 15
Power consumption ........................... 15
Power supply failure .......................... 15
Electrical connection .......................... 16
Potential equalization ......................... 19
Terminals ................................. 19
Cable entries ............................... 19
Cable specification ............................ 19
Overvoltage protection ......................... 19
Performance characteristics .................. 20
Reference operating conditions ................... 20
Maximum measured error ....................... 20
Repeatability ............................... 21
Response time .............................. 21
Influence of ambient temperature ................. 21
Influence of medium temperature .................. 22
Influence of medium pressure .................... 22
Design fundamentals .......................... 22
Installation ............................... 23
Mounting location ............................ 23
Orientation ................................ 24
Inlet and outlet runs .......................... 25
Special mounting instructions .................... 25
Environment .............................. 25
Ambient temperature range ..................... 25
Storage temperature .......................... 30
Climate class ............................... 30
Degree of protection .......................... 30
Shock resistance ............................. 31
Vibration resistance ........................... 31
Interior cleaning ............................. 31
Electromagnetic compatibility (EMC) ............... 31
Process .................................. 31
Medium temperature range ...................... 31
Medium density ............................. 31
Pressure-temperature ratings .................... 31
Secondary containment pressure range .............. 34
Rupture disk ................................ 35
Flow limit ................................. 35
Pressure loss ............................... 35
System pressure ............................. 35
Thermal insulation ........................... 35
Heating ................................... 35
Vibrations ................................. 35
Mechanical construction .................... 36
Design, dimensions ........................... 36
Weight ................................... 49
Materials .................................. 49
Process connections ........................... 51
Operability ............................... 51
Operating concept ............................ 51
Local operation .............................. 52
Remote operation ............................ 53
Certificates and approvals ................... 54
CE mark ................................... 54
C-Tick symbol ............................... 54
Ex approval ................................ 54
Hygienic compatibility ......................... 55
Functional safety ............................. 55
Certification PROFIBUS ......................... 55
Pressure Equipment Directive .................... 55
Other standards and guidelines ................... 56
Ordering information ....................... 56
Application packages ....................... 57
Diagnostics functions .......................... 57
Heartbeat Technology ......................... 57
Accessories ............................... 57
Device-specific accessories ...................... 57
Communication-specific accessories ................ 58
Service-specific accessories ...................... 59
System components ........................... 60
Documentation ............................ 60
Standard documentation ........................ 60
Supplementary device-dependent documentation ....... 60
Registered trademarks ...................... 61

Proline Promass E 200
Endress+Hauser 3
Document information
Symbols used Electrical symbols
Symbol Meaning
A0011197
Direct current
A terminal to which DC voltage is applied or through which direct current flows.
A0011198
Alternating current
A terminal to which alternating voltage is applied or through which alternating current flows.
A0017381
Direct current and alternating current
• A terminal to which alternating voltage or DC voltage is applied.
• A terminal through which alternating current or direct current flows.
A0011200
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a grounding
system.
A0011199
Protective ground connection
A terminal which must be connected to ground prior to establishing any other connections.
A0011201
Equipotential connection
A connection that has to be connected to the plant grounding system: This may be a potential
equalization line or a star grounding system depending on national or company codes of practice.
Symbols for certain types of information
Symbol Meaning
A0011182
Allowed
Indicates procedures, processes or actions that are allowed.
A0011183
Preferred
Indicates procedures, processes or actions that are preferred.
A0011184
Forbidden
Indicates procedures, processes or actions that are forbidden.
A0011193
Tip
Indicates additional information.
A0011194
Reference to documentation
Refers to the corresponding device documentation.
A0011195
Reference to page
Refers to the corresponding page number.
A0011196
Reference to graphic
Refers to the corresponding graphic number and page number.
A0015502
Visual inspection
Symbols in graphics
Symbol Meaning
1, 2, 3,... Item numbers
,… ,
Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections

Proline Promass E 200
4 Endress+Hauser
Symbol Meaning
A0013441
Flow direction
-
A0011187
Hazardous area
Indicates a hazardous area.
.
A0011188
Safe area (non-hazardous area)
Indicates a non-hazardous area.
Function and system design
Measuring principle The measuring principle is based on the controlled generation of Coriolis forces. These forces are
always present in a system when both translational and rotational movements are superimposed.
Fc = 2 · ∆m (ν · ω)
Fc = Coriolis force
∆m = moving mass
ω = rotational velocity
ν = radial velocity in rotating or oscillating system
The amplitude of the Coriolis force depends on the moving mass ∆m, its velocity ν in the system and
thus on the mass flow. Instead of a constant rotational velocity ω, the sensor uses oscillation.
In the sensor, two parallel measuring tubes containing flowing fluid oscillate in antiphase, acting like
a tuning fork. The Coriolis forces produced at the measuring tubes cause a phase shift in the tube
oscillations (see illustration):
• At zero flow (when the fluid is at a standstill) the two tubes oscillate in phase (1).
• Mass flow causes deceleration of the oscillation at the inlet of the tubes (2) and acceleration at the
outlet (3).
1 2 3
A0016771
The phase difference (A-B) increases with increasing mass flow. Electrodynamic sensors register the
tube oscillations at the inlet and outlet. System balance is ensured by the antiphase oscillation of the
two measuring tubes. The measuring principle operates independently of temperature, pressure,
viscosity, conductivity and flow profile.
Density measurement
The measuring tube is continuously excited at its resonance frequency. A change in the mass and
thus the density of the oscillating system (comprising measuring tube and fluid) results in a
corresponding, automatic adjustment in the oscillation frequency. Resonance frequency is thus a
function of medium density. The microprocessor utilizes this relationship to obtain a density signal.
Volume measurement
Together with the measured mass flow, this is used to calculate the volume flow.

Proline Promass E 200
Endress+Hauser 5
Temperature measurement
The temperature of the measuring tube is determined in order to calculate the compensation factor
due to temperature effects. This signal corresponds to the process temperature and is also available
as an output signal.
Measuring system The device consists of a transmitter and a sensor.
One device version is available: compact version, transmitter and sensor form a mechanical unit.
Transmitter
Promass 200 Device versions and materials:
• Compact, aluminum coated:
Coated aluminum AlSi10Mg
• Compact, hygienic, stainless:
Hygienic version, for maximum corrosion resistance: stainless steel
1.4404 (316L)
Configuration:
• External operation via four-line, illuminated local display with touch
control and guided menus ("Make-it-run" wizards) for applications
• Via operating tools (e.g. FieldCare)
A0013471
Sensor
Promass E • Multipurpose sensor
• Ideal substitute for volumetric flowmeters
• Nominal diameter range: DN 8 to 50 (³⁄₈ to 2")
• Materials:
– Sensor: stainless steel 1.4301 (304)
– Measuring tubes: stainless steel 1.4539 (904L)
– Process connections: stainless steel 1.4404 (316/316L)
A0013472
Input
Measured variable Direct measured variables
• Mass flow
• Density
• Temperature
Calculated measured variables
• Volume flow
• Corrected volume flow
• Reference density
Measuring range Measuring ranges for liquids
DN Measuring range full scale values min(F) to max(F)
[mm] [in] [kg/h] [lb/min]
8 ³⁄₈ 0 to 2 000 0 to 73.5
15 ½ 0 to 6 500 0 to 238
25 1 0 to 18 000 0 to 660
40 1½ 0 to 45 000 0 to 1 650
50 2 0 to 70 000 0 to 2 570

Proline Promass E 200
6 Endress+Hauser
Measuring ranges for gases
The full scale values depend on the density of the gas and can be calculated with the formula below:
max(G) =  max(F) · ρG : x
 max(G) Maximum full scale value for gas [kg/h]
 max(F) Maximum full scale value for liquid [kg/h]
 max(G) <  max(F)  max(G) can never be greater than  max(F)
ρGGas density in [kg/m³] at operating conditions
DN x
[mm] [in] [kg/m3]
8 ³⁄₈ 85
15 ½ 110
25 1 125
40 1½ 125
50 2 125
To calculate the measuring range, use the Applicator sizing tool (→  59)
Calculation example for gas
• Sensor: Promass E, DN 50
• Gas: Air with a density of 60.3 kg/m³ (at 20 °C and 50 bar)
• Measuring range (liquid):70 000 kg/h
• x = 125 kg/m³ (for Promass E, DN 50)
Maximum possible full scale value:
 max(G) =  max(F) · ρG : x = 70 000 kg/h · 60.3 kg/m³ : 125 kg/m³ = 33 800 kg/h
Recommended measuring range
"Flow limit" section (→  35)
Operable flow range Over 1000 : 1.
Flow rates above the preset full scale value are not overridden by the electronics unit, with the result
that the totalizer values are registered correctly.
Input signal External measured values
To increase the accuracy of certain measured variables or to calculate the corrected volume flow for
gases, the automation system can continuously write the operating pressure to the measuring
device. Endress+Hauser recommends the use of a pressure transmitter for absolute pressure, e.g.
Cerabar M or Cerabar S.
Various pressure transmitters and temperature measuring devices can be ordered from Endress
+Hauser: see "Accessories" section (→  60)
It is recommended to read in external measured values to calculate the following measured variables:
• Mass flow
• Corrected volume flow
HART protocol
The measured values are written from the automation system to the measuring device via the HART
protocol. The pressure transmitter must support the following protocol-specific functions:
• HART protocol
• Burst mode

Proline Promass E 200
Endress+Hauser 7
Fieldbuses
The measured values can be written from the automation system to the measuring via:
PROFIBUS-PA
Output
Output signal Current output
Current output 1 4-20 mA HART (passive)
Current output 2 4-20 mA (passive)
Resolution <1 µA
Damping Adjustable: 0.0 to 999.9 s
Assignable measured
variables
• Mass flow
• Volume flow
• Corrected volume flow
• Density
• Reference density
• Temperature
Pulse/frequency/switch output
Function Can be set to pulse, frequency or switch output
Version Passive, open collector
Maximum input values • DC 35 V
• 50 mA
For information on the Ex connection values (→  10)
Voltage drop • For ≤2 mA: 2 V
• For 10 mA: 8 V
Residual current ≤0.05 mA
Pulse output
Pulse width Adjustable: 5 to 2 000 ms
Maximum pulse rate 100 Impulse/s
Value per pulse Adjustable
Assignable measured
variables
• Mass flow
• Volume flow
• Corrected volume flow
Frequency output
Output frequency Adjustable: 0 to 1 000 Hz
Damping Adjustable: 0 to 999 s
Pulse/pause ratio 1:1
Assignable measured
variables
• Mass flow
• Volume flow
• Corrected volume flow
• Density
• Reference density
• Temperature
Switch output
Switching behavior Binary, conductive or non-conductive
Switching delay Adjustable: 0 to 100 s

Proline Promass E 200
8 Endress+Hauser
Number of switching
cycles
Unlimited
Assignable functions • Off
• On
• Diagnostic behavior
• Limit value
– Mass flow
– Volume flow
– Corrected volume flow
– Density
– Reference density
– Temperature
– Totalizer 1-3
• Flow direction monitoring
• Status
– Partially filled pipe detection
– Low flow cut off
PROFIBUS PA
Signal encoding Manchester Bus Powered (MBP)
Data transfer 31.25 KBit/s, Voltage mode
Signal on alarm Depending on the interface, failure information is displayed as follows:
Current output
4-20 mA
Failure mode Selectable (as per NAMUR recommendation NE 43):
• Minimum value: 3.6 mA
• Maximum value: 22 mA
• Defined value: 3.59 to 22.5 mA
• Actual value
• Last valid value
HART
Device diagnostics Device condition can be read out via HART Command 48
Pulse/frequency/switch output
Pulse output
Failure mode Choose from:
• Actual value
• No pulses
Frequency output
Failure mode Choose from:
• Actual value
• Defined value: 0 to 1 250 Hz
• 0 Hz
Switch output
Failure mode Choose from:
• Current status
• Open
• Closed

Proline Promass E 200
Endress+Hauser 9
PROFIBUS PA
Status and alarm
messages
Diagnostics in accordance with PROFIBUS PA Profile 3.02
Error current FDE (Fault
Disconnection Electronic)
0 mA
Local display
Plain text display With information on cause and remedial measures
Backlight Additionally for device version with SD03 local display: red lighting indicates a
device error.
Status signal as per NAMUR recommendation NE 107
Operating tool
• Via digital communication:
– HART protocol
– PROFIBUS PA
• Via service interface
Plain text display With information on cause and remedial measures
Additional information on remote operation (→  53)
Load Load for current output: 0 to 500 Ω, depending on the external supply voltage of the power supply
unit
Calculation of the maximum load
Depending on the supply voltage of the power supply unit (US), the maximum load (RB) including
line resistance must be observed to ensure adequate terminal voltage at the device. In doing so,
observe the minimum terminal voltage (→  15)
• For US = 18 to 18.9 V: RB≤ (US - 18 V) :0.0036 A
• For US = 18.9 to 24.5 V: RB≤ (US - 13.5 V) :0.022 A
• For US = 24.5 to 30 V: RB≤500 Ω
0
100
200
300
400
500
14 16 18 20 22 24 26 28 30 32 U [V]
s
R [ ]
bW1.1 1.21
34 36
A0013563
1 Operating range
1.1 For order code for "Output", option A "4-20 mA HART"/option B "4-20 mA HART, pulse/frequency/switch
output" with Ex i and option C "4-20 mA HART, 4-20 mA"
1.2 For order code for "Output", option A "4-20 mA HART"/option B "4-20 mA HART, pulse/frequency/switch
output" with non-Ex and Ex d

Proline Promass E 200
10 Endress+Hauser
Sample calculation
Supply voltage of the supply unit: US = 19 V
Maximum load: RB≤ (19 V - 13.5 V) :0.022 A = 250 Ω
Ex connection data Safety-related values
Ex d type of protection
Order code for "Output" Output type Safety-related values
Option A4-20mA HART Unom = DC 35 V
Umax = 250 V
Option B4-20mA HART Unom = DC 35 V
Umax = 250 V
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W 1)
Option C4-20mA HART Unom = DC 30 V
Umax = 250 V
4-20mA
Option GPROFIBUS PA Unom = DC 32 V
Umax = 250 V
Pmax = 0.88 W
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W 1)
1) Internal circuit limited by Ri = 760.5 Ω
Ex nA type of protection
Order code for "Output" Output type Safety-related values
Option A4-20mA HART Unom = DC 35 V
Umax = 250 V
Option B4-20mA HART Unom = DC 35 V
Umax = 250 V
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W 1)
Option C4-20mA HART Unom = DC 30 V
Umax = 250 V
4-20mA
Option GPROFIBUS PA Unom = DC 32 V
Umax = 250 V
Pmax = 0.88 W
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W
1) Internal circuit limited by Ri = 760.5 Ω

Proline Promass E 200
Endress+Hauser 11
Intrinsically safe values
Type of protection Ex ia
Order code for "Output" Output type Intrinsically safe values
Option A4-20mA HART Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 5 nF
Option B4-20mA HART Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 5 nF
Pulse/frequency/switch output Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 6 nF
Option C4-20mA HART Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 30 nF
4-20mA
Option GPROFIBUS PA STANDARD
Ui = 30 V
li = 300 mA
Pi = 1.2 W
Li = 10 µH
Ci = 5 nF
FISCO
Ui = 17.5 V
li = 550 mA
Pi = 5.5 W
Li = 10 µH
Ci = 5 nF
Pulse/frequency/switch output Ui = 30 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Type of protection Ex ic
Order code for "Output" Output type Intrinsically safe values
Option A4-20mA HART Ui = DC 35 V
Ii = n.a.
Pi = 1 W
Li = 0 μH
Ci = 5 nF
Option B4-20mA HART Ui = DC 35 V
Ii = n.a.
Pi = 1 W
Li = 0 μH
Ci = 5 nF
Pulse/frequency/switch output Ui = DC 35 V
Ii = n.a.
Pi = 1 W
Li = 0 μH
Ci = 6 nF
Option C4-20mA HART Ui = DC 30 V
Ii = n.a.
Pi = 1 W
Li = 0 μH
Ci = 30 nF
4-20mA

Proline Promass E 200
12 Endress+Hauser
Order code for "Output" Output type Intrinsically safe values
Option GPROFIBUS PA STANDARD
Ui = 32 V
li = 300 mA
Pi = n.a.
Li = 10 µH
Ci = 5 nF
FISCO
Ui = 17.5 V
li = n.a.
Pi = n.a.
Li = 10 µH
Ci = 5 nF
Pulse/frequency/switch output Ui = 35 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
IS type of protection
Order code for "Output" Output type Intrinsically safe values
Option A4-20mA HART Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 5 nF
Option B4-20mA HART Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 5 nF
Pulse/frequency/switch output Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 6 nF
Option C4-20mA HART Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 30 nF
4-20mA
Option GPROFIBUS PA STANDARD
Ui = 30 V
li = 300 mA
Pi = 1.2 W
Li = 10 µH
Ci = 5 nF
FISCO
Ui = 17.5 V
li = 550 mA
Pi = 5.5 W
Li = 10 µH
Ci = 5 nF
Pulse/frequency/switch output Ui = 30 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Low flow cut off The switch points for low flow cut off are user-selectable.
Galvanic isolation All outputs are galvanically isolated from one another.
Protocol-specific data HART
Manufacturer ID 0x11
Device type ID 0x54
HART protocol revision 7
Device description files
(DTM, DD)
Information and files under:
www.endress.com

Proline Promass E 200
Endress+Hauser 13
HART load • Min. 250 Ω
• Max. 500 Ω
Dynamic variables The measured variables can be freely assigned to the dynamic variables.
Measured variables for PV (primary dynamic variable)
• Mass flow
• Volume flow
• Corrected volume flow
• Density
• Reference density
• Temperature
Measured variables for SV, TV, QV (secondary, tertiary and quaternary
dynamic variable)
• Mass flow
• Volume flow
• Corrected volume flow
• Density
• Reference density
• Temperature
• Totalizer 1
• Totalizer 2
• Totalizer 3
PROFIBUS PA
Manufacturer ID 0x11
Ident number 0x155F
Profile version 3.02
Device description files (GSD,
DTM, DD)
Information and files under:
•www.endress.com
•www.profibus.org
Output values
(from measuring device to
automation system)
Analog input 1 to 6
• Mass flow
• Volume flow
• Corrected volume flow
• Density
• Reference density
• Temperature
Digital input 1 to 2
• Status
• Partially filled pipe detection
• Low flow cut off
• Switch output
Totalizer 1 to 3
• Mass flow
• Volume flow
• Corrected volume flow
Input values
(from automation system to
measuring device)
Analog output
External pressure, gage pressure, density, temperature or second temperature
(for delta heat measurement)
Digital output 1 to 3 (fixed assignment)
• Digital output 1: switch positive zero return on/off
• Digital output 2: switch switch output on/off
• Digital output 3: Start verification
Totalizer 1 to 3
• Totalize
• Reset and hold
• Preset and hold
• Operating mode configuration:
– Net flow total
– Forward flow total
– Reverse flow total

Proline Promass E 200
14 Endress+Hauser
Supported functions • Identification & Maintenance
Simplest device identification on the part of the control system and
nameplate
• PROFIBUS upload/download
Reading and writing parameters is up to ten times faster with PROFIBUS
upload/download
• Condensed status
Simplest and self-explanatory diagnostic information by categorizing
diagnostic messages that occur
Configuration of the device
address
• DIP switches on the I/O electronics module
• Local display
• Via operating tools (e.g. FieldCare)
Power supply
Terminal assignment Transmitter
Connection versions
–
4
+
1
–
2
+
3
1
23
A0013570
+
1
–
2
–
4
+
3
1
23
A0018161
Maximum number of terminals, without integrated
overvoltage protection
Maximum number of terminals, with integrated
overvoltage protection
1
2
3
Output 1 (passive): supply voltage and signal transmission
Output 2 (passive): supply voltage and signal transmission
Ground terminal for cable shield
Order code for "Output" Terminal numbers
Output 1 Output 2
1 (+) 2 (-) 3 (+) 4 (-)
Option A4-20 mA HART (passive) -
Option B 1) 4-20 mA HART (passive) Pulse/frequency/switch output
(passive)
Option C 1) 4-20 mA HART (passive) 4-20 mA (passive)
Option G 2) PROFIBUS PA Pulse/frequency/switch output
(passive)
1) Output 1 must always be used; output 2 is optional.
2) PROFIBUS PA with integrated reverse polarity protection.
Pin assignment, device plug Profibus PA
PROFIBUS PA (device-side), M12 plug
1
2
4
3
A0019021
Pin Assignment Coding Plug/socket
1 + PROFIBUS PA + A Plug
2 Grounding

Proline Promass E 200
Endress+Hauser 15
3 - PROFIBUS PA –
4 Not assigned
Supply voltage Transmitter
An external power supply is required for each output. The following supply voltage values apply for
the 4-20 mA and 4-20 mA HART current output:
An external power supply is required for each output. The following supply voltage values apply for
PROFIBUS PA and the pulse/frequency/switch output:
Order code for "Output" Minimum terminal
voltage
Maximum terminal
voltage
Option A 1) 2): 4-20 mA HART For 4 mA: ≥ DC 18 V
For 20 mA: ≥ DC 14 V
DC 35 V
Option B 1) 2): 4-20 mA HART, pulse/frequency/switch
output
For 4 mA: ≥ DC 18 V
For 20 mA: ≥ DC 14 V
DC 35 V
Option C 1) 2): 4-20 mA HART, 4-20 mA For 4 mA: ≥ DC 18 V
For 20 mA: ≥ DC 14 V
DC 30 V
Option G 3): PROFIBUS PA, pulse/frequency/switch
output
9 V DC 32 V
1) External supply voltage of the power supply unit with load.
2) For device versions with SD03 local display: The terminal voltage must be increased by DC 2 V if
backlighting is used.
3) For device version with SD03 local display: The terminal voltage must be increased by DC 0.5 V if
backlighting is used.
For information about the load see (→  9)
Various power supply units can be ordered from Endress+Hauser: see "Accessories" section
(→  60)
For information on the Ex connection values (→  10)
Power consumption Transmitter
Order code for
"Output"
Maximum
Power consumption
Option A: 4-20 mA HART 770 mW
Option B: 4-20 mA HART,
Pulse/frequency/switch output
• Operation with output 1: 770 mW
• Operation with output 1 and 2: 2 770 mW
Option C: 4-20 mA HART, 4-20 mA • Operation with output 1: 660 mW
• Operation with output 1 and 2: 1 320 mW
Option G: PROFIBUS PA, pulse/frequency/switch output • Operation with output 1: 512 mW
• Operation with output 1 and 2: 2 512 mW
For information on the Ex connection values (→  10)
Power supply failure • Totalizers stop at the last value measured.
• Configuration is retained in the device memory (HistoROM).
• Error messages (incl. total operated hours) are stored.

Proline Promass E 200
16 Endress+Hauser
Electrical connection Connecting the transmitter
1
2
A0015510
1 Cable entry for output 1
2 Cable entry for output 2
Connection examples
Current output 4-20 mA HART
24
4...20 mA
5631
+
-
7
+
-
A0015511
 1 Connection example for 4-20 mA HART current output (passive)
1 Automation system with current input (e.g. PLC)
2 Active barrier for power supply (e.g. RN221N) (→  19)
3 Cable shield, observe cable specifications (→  19)
4 Resistor for HART communication (≥ 250 Ω): observe maximum load (→  9)
5 Connection for HART operating devices (→  53)
6 Analog display unit: observe maximum load (→  9)
7 Transmitter
Current output 4-20 mA
2
4...20 mA
3
1
+
-
4
+
–
+
-
A0015512
 2 Connection example for 4-20 mA current output (passive)
1 Automation system with current input (e.g. PLC)
2 Active barrier for power supply (e.g. RN221N) (→  15)
3 Analog display unit: observe maximum load (→  9)
4 Transmitter

Proline Promass E 200
Endress+Hauser 17
Pulse/frequency output
1
+
_
12345
2
+
–
+
–
3
A0016801
 3 Connection example for pulse/frequency output (passive)
1 Automation system with pulse/frequency input (e.g. PLC)
2 Power supply
3 Transmitter: observe input values (→  7)
Switch output
1
+
_
+
_
2
+
_3
A0016802
 4 Connection example for switch output (passive)
1 Automation system with switch input (e.g. PLC)
2 Power supply
3 Transmitter: observe input values (→  7)

Proline Promass E 200
18 Endress+Hauser
PROFIBUS-PA
21 3
+
-+
-
+
-
4
5
5
78
66
6
6
6
6
.-
A0019004
 5 Connection example for PROFIBUS-PA
1 Control system (e.g. PLC)
2 Segment coupler PROFIBUS DP/PA
3 Cable shield
4 T-box
5 Measuring device
6 Local grounding
7 Bus terminator
8 Potential matching line
HART input
3
4...20 mA
5
1
+
-
3
6
+
–
+
+
–
+
–
+
–
+
–
–
24
4
7
+
-
A0016029
 6 Connection example for HART input with a common negative
1 Automation system with HART output (e.g. PLC)
2 Resistor for HART communication (≥ 250 Ω): observe maximum load (→  9)
3 Active barrier for power supply (e.g. RN221N) (→  15)
4 Cable shield, observe cable specifications (→  19)
5 Analog display unit: observe maximum load (→  9)
6 Pressure transmitter (e.g. Cerabar M, Cerabar S): see requirements (→  6)
7 Transmitter

Proline Promass E 200
Endress+Hauser 19
Potential equalization No special measures for potential equalization are required.
For devices intended for use in hazardous locations, please observe the guidelines in the Ex
documentation (XA).
Terminals • For device version without integrated overvoltage protection: plug-in spring terminals for wire
cross-sections 0.5 to 2.5 mm2 (20 to 14 AWG)
• For device version with integrated overvoltage protection: screw terminals for wire cross-sections
0.2 to 2.5 mm2 (24 to 14 AWG)
Cable entries • Cable gland (not for Ex d): M20 × 1.5 with cable 6 to 12 mm (0.24 to 0.47 in)
• Thread for cable entry:
– For non-Ex and Ex: NPT ½"
– For non-Ex and Ex (not for CSA Ex d/XP): G ½"
– For Ex d: M20 × 1.5
Cable specification Permitted temperature range
• –40 °C (–40 °F) to +80 °C (+176 °F)
• Minimum requirement: cable temperature range ≥ ambient temperature +20 K
Signal cable
Current output
• For 4-20 mA: standard installation cable is sufficient.
• For 4-20 mA HART: Shielded cable recommended. Observe grounding concept of the plant.
Pulse/frequency/switch output
Standard installation cable is sufficient.
PROFIBUS PA
Twisted, shielded two-wire cable. Cable type A is recommended.
For further information on planning and installing PROFIBUS PA networks see:
• Operating Instructions "PROFIBUS DP/PA: Guidelines for planning and commissioning"
(BA00034S)
• PNO Directive 2.092 "PROFIBUS PA User and Installation Guideline"
• IEC 61158-2 (MBP)
Overvoltage protection The device can be ordered with integrated overvoltage protection for diverse approvals:
Order code for "Accessory mounted", option NA "Overvoltage protection"
Input voltage range Values correspond to supply voltage specifications (→  15) 1)
Resistance per channel 2 ⋅0.5 Ω max
DC sparkover voltage 400 to 700 V
Trip surge voltage <800 V
Capacitance at 1 MHz <1.5 pF
Nominal discharge current
(8/20 μs)
10 kA
Temperature range –40 to +85 °C (–40 to +185 °F)
1) The voltage is reduced by the amount of the internal resistance Imin⋅ Ri
Depending on the temperature class, restrictions apply to the ambient temperature for device
versions with overvoltage protection (→  26)

Proline Promass E 200
20 Endress+Hauser
Performance characteristics
Reference operating
conditions
• Error limits based on ISO 11631
• Water with +15 to +45 °C (+59 to +113 °F) at2 to 6 bar (29 to 87 psi)
• Specifications as per calibration protocol
• Accuracy based on accredited calibration rigs that are traced to ISO 17025.
To obtain measured errors, use the Applicator sizing tool (→  59)
Maximum measured error o.r. = of reading; 1 g/cm³ = 1 kg/l; T = medium temperature
Base accuracy
Mass flow and volume flow (liquids)
±0.25 % o.r.
Mass flow (gases)
±0.75 % o.r.
Design fundamentals (→  22)
Density (liquids)
• Reference conditions:±0.0005 g/cm³
• Standard density calibration:±0.02 g/cm³
(valid over the entire temperature range and density range )
Temperature
±0.5 °C ± 0.005 · T °C (±0.9 °F ± 0.003 · (T – 32) °F)
Zero point stability
DN Zero point stability
[mm] [in] [kg/h] [lb/min]
8 ³⁄₈ 0.24 0.0088
15 ½ 0.78 0.0287
25 1 2.16 0.0794
40 1½ 5.40 0.1985
50 2 8.40 0.3087
Flow values
Flow values as turndown parameter depending on nominal diameter.
SI units
DN 1:1 1:10 1:20 1:50 1:100 1:500
[mm] [kg/h] [kg/h] [kg/h] [kg/h] [kg/h] [kg/h]
8 2 000 200 100 40 20 4
15 6 500 650 325 130 65 13
25 18 000 1 800 900 360 180 36
40 45 000 4 500 2 250 900 450 90
50 70 000 7 000 3 500 1 400 700 140