Endress+Hauser Teqwave T User manual

Products Solutions Services
BA01824D/06/EN/01.17
71385957
Valid from software version:
2.1.zz (device firmware)
Operating Instructions
Teqwave T
Measuring device with acoustic surface wave technology
I
RFID

Teqwave T
2Endress+Hauser
• Make sure the Operating Instructions are stored in a safe place so they are always available
when working on or with the device.
• To avoid danger to individuals or the facility, read the "Basic safety instructions" section
carefully, as well as all other safety instructions in the Operating Instructions that are spe-
cific to working procedures.
• The manufacturer reserves the right to modify technical data without prior notice. The
Endress+Hauser Sales Center will supply you with current information about, and updates
to, these Operating Instructions.

Teqwave T
Endress+Hauser 3
Table of contents
1 About this document . . . . . . . . . . . . . . . . 4
1.1 Document purpose . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . 5
2 Basic safety instructions . . . . . . . . . . . . . 6
2.1 Requirements for personnel . . . . . . . . . . . . . . . . . . 6
2.2 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Occupational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5 Product safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.6 IT security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Product description . . . . . . . . . . . . . . . . . 8
3.1 Product design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.2 Concentration apps and measurement points . . . . 8
4 Incoming acceptance and product
identification . . . . . . . . . . . . . . . . . . . . .10
4.1 Incoming acceptance . . . . . . . . . . . . . . . . . . . . . . 10
4.2 Product identification . . . . . . . . . . . . . . . . . . . . . . 10
5 Storage and transport . . . . . . . . . . . . . . 12
5.1 Storage conditions . . . . . . . . . . . . . . . . . . . . . . . . 12
5.2 Transporting the product . . . . . . . . . . . . . . . . . . . 12
5.3 Packaging disposal . . . . . . . . . . . . . . . . . . . . . . . . 12
6 Electrical connection . . . . . . . . . . . . . . . 13
6.1 Connection conditions . . . . . . . . . . . . . . . . . . . . . 13
6.2 Connecting the measuring device . . . . . . . . . . . . 13
6.3 Post-connection check . . . . . . . . . . . . . . . . . . . . . 14
7 Operating options . . . . . . . . . . . . . . . . . 15
7.1 Overview of the operating options . . . . . . . . . . . 15
7.2 Access to the measuring device via the local display
15
7.3 Access to the measuring device via the operating
tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8 Commissioning. . . . . . . . . . . . . . . . . . . .24
8.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8.2 Charging the battery . . . . . . . . . . . . . . . . . . . . . . . 24
8.3 Switching on the measuring device . . . . . . . . . . 24
8.4 Configuring the measuring device . . . . . . . . . . . 25
8.5 Advanced settings via the operating tool . . . . . . 26
9 Operation. . . . . . . . . . . . . . . . . . . . . . . . . 33
9.1 Changing the operating language . . . . . . . . . . . . 33
9.2 Performing the measurement . . . . . . . . . . . . . . . 33
9.3 Reading measured values . . . . . . . . . . . . . . . . . . . 34
9.4 Additional dosage . . . . . . . . . . . . . . . . . . . . . . . . . . 35
9.5 Accessing the measured data . . . . . . . . . . . . . . . . 37
9.6 Loading measured values in the operating tool . 38
9.7 Updating the firmware . . . . . . . . . . . . . . . . . . . . . 38
10 Diagnostics and troubleshooting . . . . 40
10.1 General troubleshooting . . . . . . . . . . . . . . . . . . . . 40
10.2 Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
10.3 Checking the measuring device . . . . . . . . . . . . . . 41
10.4 Device information . . . . . . . . . . . . . . . . . . . . . . . . . 42
10.5 Firmware history . . . . . . . . . . . . . . . . . . . . . . . . . . 42
11 Maintenance . . . . . . . . . . . . . . . . . . . . . 43
11.1 Maintenance tasks . . . . . . . . . . . . . . . . . . . . . . . . . 43
11.2 Endress+Hauser services . . . . . . . . . . . . . . . . . . . . 43
12 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . 44
12.1 General information . . . . . . . . . . . . . . . . . . . . . . . . 44
12.2 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
12.3 Endress+Hauser services . . . . . . . . . . . . . . . . . . . . 44
12.4 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
12.5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
13 Accessories. . . . . . . . . . . . . . . . . . . . . . . 46
13.1 Device-specific accessories . . . . . . . . . . . . . . . . . . 46
13.2 Service-specific accessories . . . . . . . . . . . . . . . . . 46
14 Technical data . . . . . . . . . . . . . . . . . . . . 47
14.1 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
14.2 Function and system design . . . . . . . . . . . . . . . . . 47
14.3 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
14.4 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
14.5 Performance characteristics . . . . . . . . . . . . . . . . . 48
14.6 Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
14.7 Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
14.8 Mechanical construction . . . . . . . . . . . . . . . . . . . . 49
14.9 Operability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
14.10 Certificates and approvals . . . . . . . . . . . . . . . . . . . 50
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

About this document Teqwave T
4Endress+Hauser
1 About this document
1.1 Document purpose
These Operating Instructions contain all the information that is required in the various pha-
ses of the life cycle of the device: from product identification, incoming acceptance and sto-
rage, to connection, operation and commissioning through to troubleshooting, maintenance
and disposal.
1.2 Symbols used
1.2.1 Safety symbols
1.2.2 Electrical symbols
1.2.3 Symbols for certain types of information
Symbol Meaning
A0011189-EN
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will
result in serious or fatal injury.
A0011190-EN
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in serious or fatal injury.
A0011191-EN
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in minor or medium injury.
A0011192-EN
NOTE
This symbol contains information on procedures and other facts which do not result in
personal injury.
Symbol Meaning
A0011197
Direct current
A terminal to which DC voltage is applied or through which direct current flows.
A0011198
Alternating current
A terminal to which alternating voltage is applied or through which alternating current
flows.
A0017381
Direct and alternating current
• A terminal to which alternating voltage or DC voltage is applied.
• A terminal through which alternating current or direct current flows.
A0011200
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a ground-
ing system.
Symbol Meaning
A0011182
Permitted
Indicates procedures, processes or actions that are permitted.
A0011183
Preferred
Indicates procedures, processes or actions that are preferred.
DANGER
WARNING
CAUTION
NOTICE

Teqwave T About this document
Endress+Hauser 5
1.2.4 Symbols in graphics
1.3 Documentation
For an overview of the scope of the associated documentation, refer to the following:
•W@M Device Viewer: enter the serial number from the nameplate (www.endress.com/
deviceviewer).
•Endress+Hauser Operations App: enter the serial number from the nameplate or scan the
2-D matrix code (QR code) on the nameplate.
1.4 Registered trademarks
Applicator
Registered or registration-pending trademark of the Endress+Hauser Group
Autotex®
Registered trademark of MacDermid Autotype Limited, Wantage, UK
DuploCOLL®
Registered trademark of Lohmann GmbH, Neuwied, Germany
Microsoft®
Registered trademark of the Microsoft Corporation, Redmond, Washington, USA
A0011184
Forbidden
Indicates procedures, processes or actions that are forbidden.
A0011193
Tip
Indicates additional information.
A0011194
Reference to documentation
Refers to the corresponding measuring device documentation.
A0011195
Reference to page
Refers to the corresponding page number.
1., 2., 3.,... Series of steps
Result of a series of actions
A0013562
Help in the event of a problem
A0015502
Visual inspection
Symbol Meaning
1, 2, 3, ... Item numbers
A, B, C, ... Views
A-A, B-B, C-C,.. Sections
A0013441
Flow direction
Symbol Meaning

Basic safety instructions Teqwave T
6Endress+Hauser
2 Basic safety instructions
2.1 Requirements for personnel
The personnel for installation, commissioning, diagnostics and maintenance must meet the
following requirements:
• Personnel must be trained, qualified specialists with a relevant qualification for the speci-
fic functions and tasks.
• Personnel must be authorized by the plant operator.
• Personnel must be familiar with federal/national regulations.
• Before starting work, personnel must read and understand the instructions in the manual,
supplementary documentation and certificates (depending on the application).
• Personnel must follow instructions and comply with general policies.
Operating personnel must meet the following requirements:
• Operating personnel must be instructed and authorized according to the requirements of
the task by the facility's operator.
• Operating personnel must follow the instructions in the manual.
2.2 Designated use
Application and fluids
Only use the measuring device described in these Operating Instructions to measure the con-
centration of liquids.
Only use the measuring device within the limits specified in the technical data and for the
specific concentration app.
To ensure that the measuring device remains in proper condition for the operation time:
‣Only use the measuring device for fluids to which the process-wetted materials are suf-
ficiently resistant.
Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage
caused by improper or non-designated use.
Other risks
Hot media can present a burn hazard
‣In the case of high fluid temperatures, ensure protection against contact to prevent
burns.
Risk of injury when changing the fluid
‣The temperature of the sensor may not exceed the flash point of the new liquid under
measurement.
‣Clean thoroughly to remove all residue of the previous liquid and avoid unwanted chemi-
cal reactions. When cleaning, make sure to use appropriate personal protection equip-
ment.
2.3 Occupational safety
When working on and with the measuring device:
‣Wear the required personal protective equipment according to federal/national regula-
tions.

Teqwave T Basic safety instructions
Endress+Hauser 7
2.4 Operational safety
Risk of injury
‣Operate the measuring device only if it is in proper technical condition, free from errors
and faults.
‣The operator is responsible for the trouble-free operation of the device.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet
state-of-the-art safety requirements, has been tested, and left the factory in a condition in
which it is safe to operate. It meets general safety standards and legal requirements. It also
complies with the EC directives listed in the device-specific EC Declaration of Conformity.
Endress+Hauser confirms this by affixing the CE mark to the device.
2.6 IT security
We only provide a warranty if the measuring device is installed and used as described in the
Operating Instructions.
IT security measures, which provide additional protection for the measuring device and
device data transfer, must be implemented by the operators themselves in line with their
security standards.
Spread of malicious software
The computer recognizes the transmitter as a mass storage medium. Because of this, mal-
ware that may be on the computer can potentially spread.
‣Ensure suitable security measures are taken, such as the use of anti-virus software.
NOTICE

Product description Teqwave T
8Endress+Hauser
3 Product description
3.1 Product design
The measuring device consists of a mobile sensor and a mobile transmitter. The following
additional components are included in the standard delivery package:
• Connecting cable
•USBcable
•USBcharger
•Carryingcase
• Printed copy of the Operating Instructions in the form of a Quick Start Guide
• Operating Instructions on a CD-ROM
• At least one concentration app and operating tool on a CD-ROM
The measuring device uses concentration apps, which are individually tailored to the mea-
surement task and encoded to work only with the serial number of a specific transmitter. In
the measuring device, each concentration app is located in a measurement point.
A0035603
Fig. 1: Key components of the measuring device
1 Mobile sensor
2 Mobile transmitter
3 Local display (touch screen)
4 Operating keys (membrane keypad)
5 Connection for connecting to the sensor
6 USB interface for charging the battery (BCv1.2 standard) and for digital data transmission to the computer
7 Connection for connecting to the transmitter
3.2 Concentration apps and measurement points
A concentration app contains specific configurations for the measurement of a certain liquid
and, along with the measured sensor signals, is used as the basis for calculating the concen-
tration. Endress+Hauser provides a separate concentration app for each liquid.
A list of the available concentration apps is provided in the Applicator →46. If you require
a concentration app that is not available in the standard settings, Endress+Hauser requires
a sample of the fluid to create the concentration app. Every transmitter can use a maximum
of 50 concentration apps.
To be able to use a concentration app on the measuring device, the user must first save the
desired concentration app in a measurement point using the operating tool. The measure-
ment point can then be loaded to the measuring device →25. It is possible to use the same
12
6
3
5
7
4
I
RFID

Teqwave T Product description
Endress+Hauser 9
concentration app for multiple measurement points.
Concentration apps are individually encoded to work only with the serial number of a specific
transmitter. The transmitter in service uses the serial number saved in the .mf2, .Imp or .lmf
file to check whether the concentration app has been specifically configured for use with this
transmitter. If this is not the case, it is not possible to add the concentration app.

Incoming acceptance and product identification Teqwave T
10 Endress+Hauser
4 Incoming acceptance and product
identification
4.1 Incoming acceptance
• If one of the conditions is not satisfied, contact the Endress+Hauser Sales Center.
• The Technical Documentation is available on the Internet or via the Endress+Hauser
Operations App →10.
4.2 Product identification
The measuring device can be identified in the following ways:
• Using the nameplate on the transmitter
• Using the order code with a breakdown of the device features on the delivery note.
• By entering the serial numbers from the nameplates in W@M Device Viewer (www.end-
ress.com/deviceviewer): all the information about the measuring device is displayed.
• By entering the serial number from the nameplate into the Endress+Hauser Operations
App or by scanning the 2-D matrix code (QR code) on the measuring device with the End-
ress+Hauser Operations App: all the information about the measuring device is displayed.
Is the order code on the delivery note (1) identical to the order code
on the product sticker (2)?
A0027449

Is the measuring device undamaged? 
Do the nameplate data match the ordering information on the delivery note? 
CD-ROM with "Teqwave Mobile Viewer" operating tool and concentration apps 
Is a CD-ROM provided with the Technical Documentation (depends on device version) and docu-
ments? 
1
2

Teqwave T Incoming acceptance and product identification
Endress+Hauser 11
4.2.1 Nameplate
A0035638
Fig. 2: Example of a nameplate on a transmitter
1 Place of manufacture
2Ordercode
3 Serial number (Ser. no.)
4 Extended order code (Ext. ord. cd.)
5 Permitted ambient temperature (T
α
)
6 Degree of protection
7 Firmware version (Device ID FW) ex-works
8 Device version (Device Rev.) ex-works
9 Barcode for internal use
10 Barcode for internal use
11 Name of the measuring device
12 2D matrix code with serial number
13 Space for approvals and certificates
4.2.2 Symbols on the measuring device
Ta
IP
Device ID FW
Device Rev.
11
13
Order code:
Ser. no.:
Ext. ord. cd.:
2
3
4
5
6
7
8
9
10
12
1
i
Symbol Meaning
#WARNING
This symbol alerts you to a life-threatening situation. Failure to avoid this situation
can result in serious or fatal injury.
A0011194
Reference to documentation
Refers to the corresponding measuring device documentation.

Storage and transport Teqwave T
12 Endress+Hauser
5 Storage and transport
5.1 Storage conditions
Observe the following notes for storage:
• Store in the original packaging to ensure protection from shock.
• Protect from direct sunlight to avoid unacceptably high surface temperatures.
• Store in a dry and dust-free place.
• Do not store outdoors.
Storage temperature →49.
5.2 Transporting the product
• Transport the measuring device to the measuring point in the original packaging.
• Use the carrying case supplied to prevent the device from being switched on unintentio-
nally.
• Do not remove protection caps mounted on connection points.
• When shipping the measuring device, the battery may not be more than 30% charged.
• When shipping, comply with Special Regulation SV 188 (transportation of lithium batte-
ries).
5.3 Packaging disposal
All packaging materials are environmentally friendly and 100% recyclable: box in
accordance with European Packaging Directive 94/62EC.

Teqwave T Electrical connection
Endress+Hauser 13
6 Electrical connection
6.1 Connection conditions
6.1.1 Requirements for connecting cables and chargers
Connecting cable between sensor and transmitter
Only use the cable supplied.
The connecting cables and chargers provided by the customer must fulfill the following
requirements.
Electrical safety
National regulations and standards apply.
USB cable
USB charger
6.2 Connecting the measuring device
6.2.1 Connecting the connecting cable
Connect the sensor to the transmitter only using the connecting cable supplied.
Damage to the measuring device
Damaged cables can impact the functional integrity of the measuring device.
‣Do not bend or shorten the connecting cable.
‣Do not remove the plug of the connecting cable.
‣Replace damaged or broken cables immediately.
‣Insert the connectors of the connecting cable into the socket at the position indicated
until they engage with a click.
Red dots on the connectors indicate the position. The two connections on the cable are
not identical - one is only designed for the sensor and the other is designed exclusively
for the transmitter.
Cable type USB 2.0, Type A to Type B
Cable length Max.2m(6.56ft)
Approval UL 2725
Connection USB socket Type A, as per BCv1.2 standard
Supply voltage 5V
Charging current 1A
Overload protection Yes
Short-circuit proof Yes
Power 6W
Charge temperature +10 to +40 °C (+34 to +104 °F)
NOTICE

Electrical connection Teqwave T
14 Endress+Hauser
6.2.2 Connecting the USB cables
Spread of malicious software
The computer recognizes the transmitter as a mass storage medium. Because of this, mal-
ware that may be on the computer can potentially spread.
‣Ensure suitable security measures are taken, such as the use of anti-virus software.
The USB port of the measuring device is used for the following:
• To charge the battery via the computer or USB charger
• To transmit data to the computer
• To establish the connection to the "Teqwave Mobile Viewer" operating tool
If connecting to the USB charger: use the USB charger supplied with the device. If using
third-party products: ensure compliance with the charger specifications →13.
If connecting to the computer: the measuring device cannot perform any measurements
during this time.
Connecting the USB cable
‣Connect the measuring device with the computer (switched on) or the USB charger via
the USB cable.
The battery symbol flashes while the measuring device is charging.
If the device is connected to the computer, the computer recognizes the measuring
device as a mass storage medium.
Possible to connect to the "Teqwave Mobile Viewer" operating tool →19.
If the battery symbol does not flash, the battery is already fully charged or the charging
temperature is outside the permitted range →13.
6.3 Post-connection check
Are the cables and measuring device undamaged (visual inspection)? 
Do the cables and charger used comply with the requirements (→13)? 
Do the cables have adequate strain relief? 
Are all the connectors firmly seated? 
If the battery is charged: is the device ready for operation and does anything appear on the local
display? 
NOTICE

Teqwave T Operating options
Endress+Hauser 15
7 Operating options
7.1 Overview of the operating options
The measuring device can be operated and configured in the following ways:
• Operation via the local display (mobile transmitter)
• Measured data configured and read out via the "Teqwave Mobile Viewer" operating tool
supplied
7.2 Access to the measuring device via the local display
The measurement procedure is started via the local display. The measuring device is confi-
gured and the measured values of the measuring device are read out using the operating tool
supplied.
7.2.1 Measurement point selection (startup screen)
After starting the measuring device, the screen appears where you can select the measure-
ment point. Use the back/repeat key on the membrane keypad to return to the measurement
point selection. Measurement points can be organized into groups and subgroups.
A0035639-EN
Fig. 3: Example: measurement point selection (startup screen)
1 Measurement point selection and measurement display area →16
2 RFID signal indicator for automatic measurement point detection (RFID is currently not available)
3 Battery charge status
4 Access settings for date and time →25
5Clock
6 Scroll function
7 Measurement point group/subgroup
8Measurementpoint
9 Information/instructions
Scroll function
The scroll function appears as of six groups or six measurement points.
Measurement point group/subgroup
Organizing measurement points into groups gives users a better overview and allows users
to find the measurement points they need more quickly. Measurement points can be orga-
nized into groups using the operating tool.
2
4
5
6
3
1
7
8
9

Operating options Teqwave T
16 Endress+Hauser
Measurement point
The operating tool allows users to create measurement points, organize the measurement
points into groups and subgroups and load them to the measuring device.
7.2.2 Measurement display area
The Measuring condition screen and the Measurement result or Error message screen
appears on the local display during a measurement.
Measuring condition screen
A0035640-EN
Fig. 4: Example: automatic measuring condition check
1 Test criterion
2 Indicator: signals whether value of test measurements is within or outside measuring range limits
3 Indicates progress of test measurement
4 Test status indicator: condition satisfied, condition not satisfied, criterion not yet tested
Measurement result screen
A0035641-EN
Fig. 5: Measurement result
1 Name of the measurement point
2 Name of the measured concentration
3 Graphic representation of the measured value with tolerance limits
4 Measured concentration, averaged over the last 10 seconds
5 Measured temperature, averaged over the last 10 seconds
1
4
2
3
2
5
4
3
1

Teqwave T Operating options
Endress+Hauser 17
Graphic measured value representation
With the graphic representation of the measured values, the measuring device presents the
measured values in relation to the limit values. The configured limit values can be viewed
with the operating tool →30.
Error message screen
A0035644-EN
Fig. 6: Error screen
1 Description of the problem and possible causes. Overview of all error messages →40
7.2.3 Information area/help text
The local display displays "Help" for every screen. This help describes the next step and helps
users to perform a measurement and analyze the measurement results.
7.2.4 Operating keys
Display Description
Green area
Measured value is within the valid range.
Yellow or red area
Measured value is outside the valid range. The measuring device can provide
a dosage recommendation for a concentration app that only displays one
concentration value if the function is enabled for the corresponding measure-
ment point.
1
1
Key Meaning
On/Off button
• Press the button briefly to switch the device on/off.
• Press the button for longer to reset the device.
Confirm key
Confirm actions.
Back/repeat key
Go back one step or repeat the measurement.
RFID key (without a function)
I
RFID

Operating options Teqwave T
18 Endress+Hauser
7.3 Access to the measuring device via the operating tool
The measuring device is configured via the "Teqwave Mobile Viewer" operating tool. In
addition, the operating tool enables the reading and graphic representation of the measured
values.
Supported functions:
• Read, display, delete and export measured values saved in the transmitter
• Create report of saved measured values
• Read out and create report of results of functional tests
• Configure the operating language of the transmitter
• Add, delete and group measurement points
• Create new measurement points
• Create and save device configurations (Configuration manager)
7.3.1 System requirements
Hardware
Computer software
7.3.2 Software installation
Installing the "Teqwave Mobile Viewer" operating tool
1. Close all applications.
2. Insert the CD-ROM supplied into the drive.
3. Double-click the "setup.exe" file to start the installation.
4. Follow the instructions in the installation window.
Connecting cable USB 2.0, Type A to Type B
Computer USB port
Screen Recommended screen resolution: min. 1024 x 768 pixels
Recommended operating
system
Microsoft Windows 7 or higher
Drivers USB driver

Teqwave T Operating options
Endress+Hauser 19
7.3.3 Establishing a connection
Spread of malicious software
The computer recognizes the transmitter as a mass storage medium. Because of this, mal-
ware that may be on the computer can potentially spread.
‣Ensure suitable security measures are taken, such as the use of anti-virus software.
When you start the operating tool for the first time, you are asked to specify the wor-
king directories where device configurations, concentration apps and measurement
points will be saved. If nothing is selected here, the operating tool creates standard
directories. This can be changed subsequently →26.
1. Switch on the measuring device.
2. Connect to the computer with the USB cable.
3. Start the "Teqwave Mobile Viewer" operating tool.
4. Via quick navigation, press the "Search for new devices" button to refresh the selection.
The device list is refreshed and the recently connected measuring device can be selec-
ted from the list via its serial number.
5. In the "Device" selection field, select the serial number of the connected measuring
device.
The measuring device and operating tool are connected.
7.3.4 User interface
A003563-EN
Fig. 7: User interface
1Menubar
2Quicknavigation
3 Graph view or graph/table view
4 Switch between graph view and graph/table view
NOTICE
1
2
3
4

Operating options Teqwave T
20 Endress+Hauser
7.3.5 Menu bar
File menu
Functions for communicating with the measuring device, for retrieving and saving measured
data that are saved in the measuring device, and for importing new measurement points or
concentration apps.
Report menu
Functions for created a report of the measured values.
Device configuration menu
Functions for configuring the measuring device.
Menu Submenu/description
Save data from selected
measurement point
Save the data of the selected measurement point to the computer.
Save data from all mea-
surement points
Save the data of all the measurement points from the selected measuring device
to the computer.
Load data Read in the data of a measurement point from the data storage location.
Import measurement
points/concentration
apps
Import the measurement point (.lmp file) or concentration app (.mf2- or .lmf
file) into the operating tool.
Search for new devices Refresh the device list when a new measuring device has been connected to the
computer via the USB port.
Eject device Disconnect the measuring device that is selected in the operating tool from the
operating tool and the operating system.
Settings •Language: select the language of the operating tool.
•Working directory: select the storage location for device configurations, con-
centration apps and measurement points.
Exit Exit the program.
Menu Description
Settings Specify the settings for creating the report.
Create Create a report, in PDF format, for measured values of the selected measure-
ment point or for a functional test that has been performed.
Functional test Display the results of the functional test for the selected measuring device in the
operating tool.
Menu Submenu/description
Measurement point •Information: open the "Measurement point information" window. Call up
measurement point information for the selected measurement point. This
includes information such as the concentration app used, the tank volume,
offset concentration, concentrate density and measuring ranges.
•Organizing: open the "Organize measurement points" window. Add or remove
available measurement points to/from the measuring device and organize
them into groups.
•Delete: remote selected measurement points from the measuring device.
•New: create new measurement points.
Measured values •Delete (current): delete the measured values of the selected measurement
point from the measuring device.
•Delete (all): delete all the measured values from the selected measuring
device.
Settings •Language: select the language of the local display.