Endress+Hauser Flowphant T DTT31 User manual

Products Solutions Services
BA00235R/09/EN/16.14
71252244
SW Version
01.00
Operating Instructions
Flowphant T
DTT31, DTT35
Flow Switch
AUTHORIZED DISTRIBUTOR:
InstrumentsAndControl.com
Houston, Texas USA
[e-mail]
832-615-3588
AUTHORIZED DISTRIBUTOR:
InstrumentsAndControl.com
Houston, Texas USA
[e-mail]
832-615-3588

Brief overview
For quick and easy commissioning:
Safety instructions →Page 4
Æ
Installation →Page 7
Æ
Wiring →Page 13
Æ
Operation →Page 14
Display and operating elements
Onsite operation
Operation with PC and configuration software
Æ
Troubleshooting →Page 32

Endress+Hauser
DTT31, DTT35
Table of contents
1 Safety instructions . . . . . . . . . . . 4
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Installation, commissioning and
operation . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Operational safety . . . . . . . . . . . . . . . . . . . 4
1.4 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5 Notes on safety conventions and icons . . 5
2 Device identification . . . . . . . . . 6
2.1 Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Certificates and approvals . . . . . . . . . . . . 6
3 Installation . . . . . . . . . . . . . . . . . 7
3.1 Incoming acceptance, storage . . . . . . . . . 7
3.2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.3 Process connection . . . . . . . . . . . . . . . . . . 8
3.4 Installation instructions . . . . . . . . . . . . . 10
4 Wiring . . . . . . . . . . . . . . . . . . . . 12
4.1 DC voltage version with M12x1
connector . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2 DC voltage version with valve connector 13
5 Operation. . . . . . . . . . . . . . . . . . 13
5.1 Onsite operation . . . . . . . . . . . . . . . . . . . 13
5.2 Operation with PC and configuration
software . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6 Maintenance. . . . . . . . . . . . . . . 26
7 Accessories . . . . . . . . . . . . . . . . 27
7.1 Welding bosses and coupling . . . . . . . . 27
7.2 Electrical connection . . . . . . . . . . . . . . . . 28
7.3 Configuration kit . . . . . . . . . . . . . . . . . . . 29
7.4 Configuration software . . . . . . . . . . . . . . 30
8 Troubleshooting. . . . . . . . . . . . 31
8.1 Error messages and warning messages 31
8.2 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.3 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.4 Change status (release) . . . . . . . . . . . . . 33
8.5 Software history . . . . . . . . . . . . . . . . . . . . 33
9 Technical data. . . . . . . . . . . . . . 34
9.1 Power supply . . . . . . . . . . . . . . . . . . . . . . . 34
9.2 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9.3 Operating conditions . . . . . . . . . .. . . . . . . . 35

Safety instructions DTT31, DTT35
4Endress+Hauser
1 Safety instructions
1.1 Designated use
The Flowphant T is a flow switch for monitoring mass flow rates in industrial processes. The
device is designed to meet state-of-the-art safety requirements and conforms to applicable
standards and EC regulations. It can, however, be a source of danger if used incorrectly or for
anything other than the designated use.
1.2 Installation, commissioning and operation
Installation, electrical connection, commissioning, operation and maintenance of the measuring
system must be carried out by trained, qualified specialists authorized to perform such work by
the facility's owner-operator. The specialist must have read and understood these Operating
Instructions and must follow the instructions they contain. The device may only be modified and
repair work carried out if this is explicitly permitted in the Operating Instructions. Damaged
devices which could be a source of danger may not be commissioned and must be labeled and
identified as defective.
1.3 Operational safety
• Functional safety
The Flowphant T flow switch has been developed in accordance with the IEC 61508 and
IEC 61511-1 (FDIS) standards. The device version with a PNP switch output and additional
analog output is equipped with features for detecting and preventing errors within the
electronics and software.
•Ex-area
The Flowphant T is not approved for use in Ex-areas.
1.4 Return
The following procedures must be carried out before a device is returned to Endress+Hauser:
• Always enclose a fully completed “Declaration of Contamination” form with the device. Only
then can Endress+Hauser transport and examine a returned device. A copy of the
“Declaration of Contamination” can be found on the second last page of these Operating
Instructions.
• Remove all fluid residues. This is particularly important if the fluid is hazardous to health, e.g.
flammable, toxic, caustic, carcinogenic, etc.
WARNING
!
Do not return a device if you are not absolutely certain that all traces of hazardous
substances have been removed, e.g. substances which have penetrated crevices or diffused
through plastic.

DTT31, DTT35 Safety instructions
Endress+Hauser 5
1.5 Notes on safety conventions and icons
Always refer to the safety instructions in these Operating Instructions labeled with the following
symbols:
Symbol Meaning
A0011190-EN
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in serious or fatal injury.
A0011191-EN
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in minor or medium injury.
A0011192-EN
NOTICE
This symbol contains information on procedures and other facts which do not
result in personal injury.
A0011193
Indicates additional information, Tip

Device identification DTT31, DTT35
6Endress+Hauser
2 Device identification
2.1 Nameplate
To identify your device, compare the complete order code and the version information on the
delivery papers with the data on the nameplate.
A0006981
Fig. 1: Nameplate for device identification (as example)
2.2 Certificates and approvals
CE mark, declaration of conformity
On leaving the factory, the device was in perfect condition from the point of view of safety. It
complies with the standards EN 61010 -1 "Protection Measures for Electrical Equipment for
Measurement, Control, Regulation and Laboratory Procedures" and with the EMC requirements
of IEC/EN 61326. The device meets the legal requirements of the EU Directives. The
manufacturer confirms a positive completion of all tests by fitting the unit with a CE mark.
Hygiene standard
The DTT35 flow switch meets the requirements of Sanitary Standard no. 74-06.
Endress+Hauser confirms this by applying the 3–A symbol (not valid for process connection
conical metal-metal).
16YV
MEASURING EQUIPMENT
m
n
o
p
q
r
s
t
u
v
Flowphant T
Made in Germany D-87484 Nesselwang
Order Code: DTT3x-xxxxxxxx
Ser.No.: xxxxxxxxxxxxxx
TAG No.: Xxxxxxxxxxxxxxxxxx
Xxxxxxxxxxxxxxxxxx
Rel.: X.XX.XX
Flow (0.03 … 3m/s; -20 °C...+85 °C)
-40°C < Ta < 85°C
Output < 250 mA
Current consump.100mA
18 - 30V DC
PNP
1
4
3
2
L+
L-
12
IP6X
mOrder code rConnection diagram
nSerial number sMeasuring range
oTAG number tAmbient temperature range
pRelease number (change status) uDegree of protection
qConnection values vApprovals
The release number indicates the change status of the device. A change in the last two
figures does not have any affect on the compatibility, →Chap. 8.4.

DTT31, DTT35 Installation
Endress+Hauser 7
UL listed for Canada and USA
The device was examined by Underwriters Laboratories Inc. (UL) in accordance with the
standards UL 61010B-1 and CSA C22.2 No. 1010.1-92 and listed under the number E225237
UL.
3 Installation
3.1 Incoming acceptance, storage
• Incoming acceptance:
Check the packaging and the device for damage. Check that the goods delivered are complete
and nothing is missing.
•Storage:
Storage temperature -40 °C to +85 °C (-40 °F to 185 °F).
3.2 Dimensions
A0005279
Fig. 2: Dimensions in mm (in)
Version L with 30 and 100 mm (1.18 and 3.94 in) for DTT31
Version L with 30, 50 and 100 mm (1.18, 1.97 and 3.94 in) for DTT35
M12x1 connector as per IEC 60947-5-2
M16x1.5 or NPT ½" valve connector as per DIN 43650A/ISO 4400
42.3 (1.66)
97.1 (3.82)
42.1 (1.66)
38.7 (1.52) 38.7 (1.52)
36 (1.42)
24 (0.95) 24 (0.95)
52 (2.05)
38.5 (1.52)
M16x1.5 / NPT ½”
M12x1
LL L
6 (0.24) 6 (0.24) 6 (0.24)

Installation DTT31, DTT35
8Endress+Hauser
3.3 Process connection
3.3.1 DTT31 design, dimensions of the process connections
A0007101
Fig. 3: Process connection versions of DTT31
m
AB C
n
L
L1
L2
L1= L2
Item
no.
Version Insertion length L Thread length L1Thread length L2
A Without process connection. For suitable
welding boss and coupling see chapter
’accessories’.
30 or 100 mm
(1.18 or 3.94 in)
--
B Thread process connection:
• ANSI NPT ¼" (m= AF15)
• ANSI NPT ½" (m= AF22)
• 14.3 mm (0.56 in)
• 19 mm (0.75 in)
• 5.8 mm (0.23 in)
• 8.1 mm (0.32 in)
C Thread process connection cylindrical as
per ISO 228:
•G¼"(n= AF19)
•G½"(n= AF27)
• 12 mm (0.47 in)
• 14 mm (0.55 in) -

DTT31, DTT35 Installation
Endress+Hauser 9
3.3.2 DTT35 design, dimensions of the process connections
A0011776
Fig. 4: Hygienic process connections. All dimensions in mm (in)
L = Insertion length L
DB DL
56.5 (2.22)
64 (2.52)
LL
18 (0.71)
HL
B
19 (0.75)
PL
13 (0.51)
PH
13 (0.51)
(APV-Inline)
(CLAMP 1”) (CLAMP 2”)
(Varivent N)
LB
18 (0.71)
(Varivent F)
(DIN 11851)
(DIN 11851)
L
13 (0.51)
PG(DIN 11851)
10 (0.39)
MB
L1
SW/
AF 22
37 (1.46)
G½”
43.5 (1.71)
50.5 (1.99)
84 (3.31)
68 (2.68) 61.5 (2.42)
82 (3.23)
100 (3.94)
66 (2.6)
50 (1.97)
51 (2.01)
68 (2.68)
27 (1.06)
44 (1.73)
39 (1.54)
56 (2.21)
Item no. Process connection versions DTT35
Insertion length L = 30, 50 or 100 mm (1.18, 1.97 or 3.94 in)
MB Conical metal-metal for hygienic processes, G½" thread, thread length L1 = 14 mm (0.55 in).
Suitable welding boss available as accessory.
DB Clamp 1"...1½" (ISO 2852) or DN 25...DN 40 (DIN 32676)
DL Clamp 2" (ISO 2852) or DN 50 (DIN 32676)
LB Varivent F DN25-32, PN 40
LL Varivent N DN40-162, PN 40
HL APV-Inline, DN50, PN40, 316L, B = bores 6 x Ø8.6 (0.34 in) + 2 x thread M8
PL DIN 11851, DN50, PN40 (including coupling nut)
PG DIN 11851, DN25, PN40 (including coupling nut)
PH DIN 11851, DN40, PN40 (including coupling nut)
The maximum process pressure for the conical metal-metal process connection
(→Fig. 4, item MB) is 16 bar!

Installation DTT31, DTT35
10 Endress+Hauser
3.4 Installation instructions
3.4.1 Installation conditions
NOTICE
Do not turn the device into the process connection thread at the housing. Always install the
device at the spanner flats (Fig. 5, item 1). Use a suitable open-ended wrench for this task (see
Table →Chap. 3.3.1).
• The onsite display can be rotated electronically 180°, →Chap. 5.1 "Onsite operation".
• The upper housing section can be rotated mechanically up to 310°.
The sensor requires a fully developed flow profile for correct monitoring.
For this reason, steadying sections (5x DN) must be provided in the pipe after a pump,
pipe bend, internal fittings and cross-sectional changes.
• The sensor tip should be completely surrounded by medium.
• Position the sensor tip in the area of maximum fluid velocity (pipe
center).
• Minimum sensor immersion length: Li≥10 mm.
A0006976
Fig. 5: Installation conditions
Orientation
• For horizontal pipes: lateral installation.
Installation from above (see Fig. 5) only if the pipe is completely
filled with medium during operation.
• For vertical pipes: installation in the ascending pipeline.
• Installation of DTT35 by min. 3° inclination, because of self draining.
A0006977
Fig. 6: Correct orientation
80
%
Li
v
m
1
80
%
80
%
80
%
3°=