Eneo MAM-5MM2203M0A User manual

EN
Quick Installation Guide
4K HD-TVI, AHD, HDCVI, CVBS,
to HDMI, VGA, CVBS, indoor
MAM-5MM2203M0A

2
Table of Contents
Package Includes...............................................................................................................................................................4
Installation Guide..........................................................................................................5
Panel View......................................................................................................................7
Description 1 – LED Indicator..................................................................................................................................7
Description 2 – Installation and Cabling .............................................................................................................8
Description 3 – Video Format & Resolutions......................................................................................................8
Description 4 – OSD Settings ..................................................................................................................................9
Installation Diagram .................................................................................................. 10
Further information .......................................................................................................................................................11

3
EN
Safety instructions
General safety instructions
• Before switching on and operating the system, rst read this safety advice and the operating instructions.
• Keep the operating instructions in a safe place for later use.
• Installation, commissioning and maintenance of the system may only be carried out by authorised
individuals and in accordance with the installation instructions - ensuring that all applicable standards and
guidelines are followed.
• Protect the devices from water penetration and humidity, since these can cause lasting damage.
• Should moisture nevertheless enter the system, under no circumstance switch on the devices under these
conditions, instead send them for examination to an authorised specialist workshop.
• The system must never be used outside of the technical specications, since this can destroy it.
• The device must be protected from excesses of heat, dust, humidity and vibration.
• When separating the system from the voltage supply, only ever use the plug to pull out the cable. Never
pull directly on the cable itself.
• Lay the connecting cables carefully and check that they are not mechanically stressed, kinked or damaged
and that no humidity can penetrate into them.
• In the event of a malfunction, please inform your supplier.
• Maintenance and repairs may only be carried out by authorised specialist personnel.
• The system must be isolated from the power supply before opening the housing.
• The device may only be opened by qualied service personnel. Unauthorised access invalidates any
warranty claim.
• Connection cables should always be exchanged through Videor E. Hartig GmbH.
• Use only original spare parts and accessories from Videor E. Hartig GmbH.
• The housing should only be cleaned using a mild domestic cleaning agent. Never use solvents or petrol as
these can permanently damage the surface.
• During installation, it is essential to ensure that the seals provided are correctly installed and that they are
not displaced during installation. Damaged seals must not be installed and will invalidate any warranty.
• The installer is responsible for the maintenance of the enclosure as per the technical data, e.g. by sealing
the cable outlets with silicone.
• Wire end ferrules should be used when shortening the exible connection cables.
• The devices may only be operated in the temperature range indicated in the data sheet and within the
dened air humidity range.

4
WEEE (Waste Electronical & Electronic Equipment)
Correct Disposal of This Product (Applicable in the European Union and other European countries with separate
collection systems).
This marking shown on the product or its literature, indicates that it should not be disposed with
other household wastes at the end of its working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate this from other types of wastes
and recycle it responsibly to promote the sustainable reuse of material resources. Household users
should contact either the retailer where they purchased this product, or their local government
oce, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal.
Graphical symbols
Please pay attention to the safety instructions, and carefully read through this instruction guide before initial
operation.
Important points of warning are marked with a caution symbol.
iImportant points of advice are marked with a notice symbol.
Package Includes
• MAM-5MM2203M0A x 1pcs
• DC12V 500mA power adapter x 1pcs
• SMT Self-tapping Screw x 4pcs
• Wall Plug x 4 pcs
• Rubber Pad x 4pcs

5
EN
Installation Guide
Install On A Table Or A Wall
Step 1: Evenly x SMT screws on a platform and leave a 2mm high clearance.
Step 2: Place MAM-5MM2203M0A on the platform and t its holes in the corresponding
screw positions.

6
Step 3: Move MAM-5MM2203M0A until it gets xed.
Use Rubber Pads to Prevent the Product from Slipping down The Platform
Fix each rubber pad at each corner of the product.

7
EN
Panel View
No. Interface Description
1 Power LED To indicate power status (Refer to Description 1).
2 Camera 1 LED To indicate Camera 1 status (Refer to Description 1).
3 Camera 2 LED To indicate Camera 2 status (Refer to Description 1).
4 OSD To control OSD menu (Refer to Description 4).
5 Audio To use a 3.5mm audio cable to connect an audio source from a HD-TVI, AHD, HDCVI camera (Refer to Description 2).
6 Camera 1 To use a coaxial cable to connect with a HD-TVI, AHD, HDCVI camera (Refer to Description 2).
7 Camera 2 /
Loop Out
To use a coaxial cable to connect with a HD-TVI, AHD, HDCVI camera, a DVR or another AD001HD4-4K (Refer to Description 3, 5).
8 HDMI To use an HDMI cable to connect with an HDMI display (Refer to Description 3).
9VGA To use aVGA cable to connect with aVGA display (Refer to Description 3).
10 CVBS To use a coaxial cable to connect with a CVBS display (Refer to Description 3).
11 Console To use a 3.5mm to RS232 cable to connect with a PC (Refer to Description 2).
12 DC 12V To connect with a DC12V 500mA power adapter.
Description 1 – LED Indicator
Interface LED Color Status
Power Green ON/ OFF Power ON/ OFF
Camera 1 Green ON/ OFF Signal Detected/ No Video
Camera 2 Green ON/ OFF Signal Detected/ No Video

8
Description 2 – Installation and Cabling
1. Avoid being in areas with electrical interferences, such as mobile phones, micro-
waves and so on, when installing your AD001HD4-4K.
2. Remove the power before installation.
3. Audio Input
• If connecting to a camera with a built-in microphone, AD001HD4-4K can only
output the video source.
4. Console
• Use DB9(Female) to 3.5mm stereo phone jack.
• Congure RS232 parameter at 115200/ 8-N-1.
• Pinout Instructions:
3.5mm Stereo Phone Jack
PIN Dene
Pin 1 RX
Pin 2 TX
Pin 3 GND
DB9 (Female)
PIN Dene
Pin 2 TX
Pin 3 RX
Pin 5 GND
Description 3 – Video Format & Resolutions
Video Input Format & Resolutions (Auto Dene HD-TVI, AHD, HDCVI, CVBS Video
Format)
Resolutions HD-TVI AHD HDCVI
8MP (4K) 12.5/15 FPS 15 FPS 15 FPS
6MP X X 20 FPS
5MP 12.5/20 FPS 20 FPS X
4MP 25/30 FPS 25/30 FPS 25/30 FPS
2MP (1080p) 25/30 FPS 25/30 FPS 25/30 FPS
1.3MP (720p) 30 FPS 25/30 FPS 25/30/50/60 FPS

9
EN
Video Output Format & Resolutions
Resolution HDMI VGA CVBS
4K2K 30/ 25Hz X X
2160p 30/ 25Hz X X
1080p 60/ 50Hz 60/ 50Hz X
1080i 60/ 50Hz 60/ 50Hz X
720p 60/ 50Hz 60/ 50Hz X
576p 60Hz 60Hz PAL
480p 60Hz 60Hz NTSC
When HDMI/ VGA resolution is set to
• 480p, 720p@60, 1080i@60, 1080p@60, 2160p@30, 4K2K@30, CVBS will be NTSC.
• 576p, 720p@50, 1080i@50, 1080p@50, 2160p@25, 4K2K@25, CVBS will be PAL.
Description 4 – OSD Settings
Use 5-Way Tactile Switch to Control OSD Menu
Button Features
●Turn ON/ OFF OSD menu
▲Up
▼Down
◄Switch function
►Switch function

10
Installation Diagram
1 in 4 out Mode (HDMI, VGA, CVBS output at the same time)
2 in 2 out Mode (Dual cameras with PIP)
2 in 3 out Mode (Dual cameras with manual switching Cam 1/ 2)

11
EN
Further information
The manual is also available from the eneo web site at www.eneo-security.com.

Technical changes reserved
© Copyright by VIDEOR E. Hartig GmbH
Version 10/2022
eneo® is a registered trademark of
VIDEOR E. Hartig GmbH
Exclusive distribution through specialised
trade channels only.
VIDEOR E. Hartig GmbH
Carl-Zeiss-Straße 8
63322 Rödermark/Germany
Tel. [phone] / 888-0
Fax [phone] / 888-100
www.videor.com
www.eneo-security.com