ENFORCER SECO-LARM SLI SK-3133-PPQ User manual

®
SK-3133-PPQ
Heavy-Duty Outdoor Access Control Keypad
with Proximity Reader
Features:
•Rugged construction – heavy-duty stainless
steel faceplate with coated steel housing
•Built-in proximity card reader
•12~24 VAC/VDC Operation, auto-adjusting
•IP66 Weatherproof rating
•Up to 1,000 user codes and/or proximity
cards for output #1, 100 for output #2, and
100 for output #3
•Up to 50 temporary visitor codes
•Up to 50 duress codes for output #1, 10 for
output #2, and 10 for output #3
•Egress input lets users exit the premises
without keying in the code
•Door sensor input for anti-
tailgating operation
•Vandal resistant, suitable for wall, post, or
gooseneck mounting

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
2SECO-LARM U.S.A., Inc.
Quick Installation Guide:
Mounting Diagram:
Quick Wiring Diagram:
12~24VDC
Power Supply
Egress button
(inside the protected premises)
Additional egress buttons can be
connected in parallel as needed
Electric
Lock
N.C. N.O.
OR
OUTPUT RELAY
N.O. Output for
Fail-secure Lock
N.C. Output for
Fail-safe Lock
N.O.
N.O.
(+)
(–)
(+)
(–)
Cathode
Diode 1N4004
(for DC use only)
12~24 VAC/VDC
This page is for installers looking to do a basic installation and programming of the keypad. For
more in
-depth installation and programming instructions, see the Table of Contents on pg. 4.
Key lock
Tamper screw
Inner back box

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
SECO-LARM U.S.A., Inc. 3
Quick Programming Guide:
This page is for installers looking to do a basic installation and programming of the keypad. For
more in
-depth installation and programming instructions, see the Table of Contents, pg. 4.
Programming Tips:
•The master programming, super user, common user, visitor, duress, and user codes
cannot be the same.
•A flashing amber LED indicates the keypad is in standby mode. A solid amber LED indicates
the
keypad is in programming mode.
•If the keypad is set for Auto Entry Mode, your codes will need to be the same number of
digits as the master programming code (see pgs. 28~29).
Programming Instructions:
Follow the instructions below if the following covers your needs:
•A new master programming code.
•A single 4-digit user code for all users, and no proximity cards.
•One output to unlock a door.
•A 3-second delay time in opening the door after the output is activated.
1. Turn off the beeping before the 1-minute power-up period ends:

2. Enter Programming Mode:

NOTE:  is the default master programming code.
3. Change the master programming code:

NOTE:  is the new master programming code.
4. Set the user code to operate output #1 (unlock the door):

NOTE:  chooses user ID #000 of 1,000 possible users (000~999).
 is the new user code for user ID #000.
5. Set the output #1 delay time (skip this step if the default value of 5 seconds is
acceptable):

NOTE: sets the output #1 delay time for 3 seconds.
6. Exit Programming Mode:


ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
4SECO-LARM U.S.A., Inc.
Table of Contents:
Contents
Quick Installation Guide:
.................................................................................................................... 2
Mounting Diagram:
............................................................................................................................ 2
Quick Wiring Diagram:
....................................................................................................................... 2
Quick Programming Gui
de: ............................................................................................................... 3
Table of Contents:
............................................................................................................................. 4
Features:
........................................................................................................................................... 5
Overview:
........................................................................................................................................... 5
Parts List:
........................................................................................................................................... 6
Specifications:
................................................................................................................................... 6
LED Indicators and Keypad Sounds:
................................................................................................. 7
IMPORTANT NOTES:
....................................................................................................................... 7
Installation:
........................................................................................................................................ 8
Wiring Diagram:
................................................................................................................................. 9
Sample Applications:
..................................................................................................................10-11
Sample Applications for Auxiliary Terminals:
.............................................................................11-13
Getting Ready to Program:
.........................................................................................................13-15
System Restore:
.............................................................................................................................. 15
Programming Format and Default Programming Values:
................................................................ 16
Programming the Master Programming Code:
................................................................................ 17
Programming the Super User Code:
..........................................................................................17-19
Programming Common
User Codes: .............................................................................................. 19
Programming User Codes and Proximity Cards:
........................................................................20-21
Programming Visitor Codes for Output #1:
...................................................................................... 22
Programming Duress Codes:
.....................................................................................................23-24
Programming the Output Mode and Output Timing:
........................................................................ 25
Programming the Real
-Time Clock: ................................................................................................ 26
Programming the Output #1 Auto
-Disable Time:........................................................................26-27
Programming the Wrong
-Code System Lock-Up: ........................................................................... 28
Programming the User Code Entry Mode:
.................................................................................28-29
Programming the Keypad Sounds:
.................................................................................................. 29
Programming the Output Relay
Activation Sounds: ........................................................................ 29
Programming the Amber LED Flashing During Standby Mode:
...................................................... 29
Programming the Door
-Forced-Open Warning and Timing:............................................................ 30
Programming the Door
-Propped-Open Warning and Delay Time:.............................................30-31
Programming the Door Open
Alarm and Timing: ............................................................................ 31
Programming the Egress Delay/Warning/Alarm:
........................................................................31-33
Direct Access to Programming:
....................................................................................................... 33
User's Guide to Operating the SK
-3133-PPQ: ................................................................................ 34
Installation Notes:
............................................................................................................................ 35
Troubleshooting:
.............................................................................................................................. 36
Also Available from
SECO-LARM®:.......................................................................................... 36

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
SECO-LARM U.S.A., Inc. 5
Features:
•Rugged construction – heavy-duty stainless
steel faceplate with coated steel housing
•Built-in proximity card reader
•12~24 VAC/VDC Operation, auto-adjusting
•Up to 1,000 possible user codes (000~999)
and/or proximity cards programmable for
output #1, 100 (001~100) for output #2, and
100 (001~100) for output #3
•Up to 50 (01~50) possible temporary visitor
codes, which can be programmed for one-
time or limited-time use (1~99 hours)
•Output #1: Form C relay, 5A@24VDC max.
•Output #2: Form C relay, 1A@24VDC max.
•Output #3: Form C relay, 1A@24VDC max.
•Outputs #1, #2, and #3 can be programmed
to activate for up to 99,999 seconds (nearly
28 hours)
•Tamper output: N.C. Dry contact,
50mA@24VDC max.
•Keypad active or alarm output selectable via
jumper
•Keypad illuminates when a button is pressed;
backlight can be programmed for FULL or
AUTO in standby mode
•IP66 Weatherproof rating
•All features are pr
ogrammed directly from the
keypad: No need for an external programmer
•EEPROM Memory protects programmed
information in case of power loss
•
Up to 50 (01~50) duress codes for output #1,
10 (01~10) for output #2, and 10 (01~10) for
output #3
•Duress code signals a silent alarm if an
authorized user is forced to open the door
under duress
•Egress input lets users exit the premises
without keying in the code
•Door sensor input for anti-
tailgating operation
•Interlocking input for connecting to a second
keypad
•Vandal resistant, suitable for wall, post, or
gooseneck mounting
Overview:
Rear:
ø1"
(ø25mm)
ø3/
16
”
(ø5mm)
1
/
2
"
(13mm)
ø5/16"
(ø8mm)
21/
2
"
(64mm)
71/16"
(180mm)
21/
2
"
(63mm)
5
1
/
4
"
(133mm)
33/
8
"
(85mm)
2
1
/
2
"
(64mm)
Front:
Side:
Key
lock
Status
LEDs

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
6SECO-LARM U.S.A., Inc.
Operating voltage
12~24 VAC/VDC
Current draw
(at 12VDC)
Standby
55mA
Keypress
90mA
Output 1 active
105mA
Output 1 & 2 active
130mA
Output 1, 2, & 3 active
150mA
Total max. current draw
220mA
Outputs
#1 – Form C
5A@24VDC
#2 – Form C
1A@24VDC
#3 – Form C
1A@24VDC
K or A
100mA@24VDC
Duress
100mA@24VDC
Interlock
100mA@24VDC
Tamper
50mA@24VDC
Inputs
Egress
N.O. Ground
Door sensor
N.C. Ground
Door inhibit
N.O. Ground
Proximity reader frequency
125kHz (EM125)
Proximity reader sensing distance
11/2" (38mm)
IP Rating
IP66
Operating humidity
5~95% Non-condensing
Operating temperature
-4°~158° F (-20°~70° C)
Material
Faceplate
1/16" (1.5mm) Stainless steel
Housing
5
/64" (2mm) Anodized steel, powder paint
Dimensions
5
1
/4"x7
1
/16"x3
3
/8" (133x180x85 mm)
Weight
3-lb 12-oz (1.7kg)
Specifications:
Parts List:
1x
Keypad with steel box
2x
Keys*
1x
Security wrench
4x
Mounting screws
4x
Mounting screw anchors
1x
Diode
1x
Mounting template
1x
Manual
*No replacement keys available. Please make extra copies for safekeeping.

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
SECO-LARM U.S.A., Inc. 7
LED Indicators and Keypad Sounds:
IMPORTANT NOTES:
LED Indicators
Red LED (left)
Amber LED (center)
Green/Red LED (right)
Steady Output #1 inhibited Programming mode
Output #1 activated (green)
Output #2 activated (red)
Flashing
Inhibit mode paused
Standby mode
Keypad Sounds and LEDs
Status
Sounds*
Amber LED (center)
In programming mode
–
Steady ON
Successful key entry
1 Beep
1 Flash
Successful code/card entry
2 Beeps
2 Flashes
Unsuccessful code/card entry
5 Beeps
5 Flashes
Power up delay
Continuous beeping
Continuous flashing
Output relay activation**
1sec long beep
–
In standby mode***
–
1 Flash/sec
System restore mode
2 Beeps
Fast flashing for 2.5 min
Card/code already stored
1 Long beep
–
Real-time clock stopped after
power loss
Continuous 3 fast beeps every 5
seconds
–
*Keypad sounds can be programmed ON or OFF (see pg. 29)
**Output relay activation sounds can be programmed for 1 second long beep, 2 short beeps,
or OFF (see pg. 29)
***Amber LED flashing during standby mode can be programmed ON or OFF (see pg. 29)
IF USING THE KEYPAD WITH A MECHANICALLY
OPERATED DOOR OR GATE, MOUNT THE KEYPAD AT
LEAST 15’ (5m) FROM THE DOOR OR GATE TO PREVENT
USERS FROM BEING CRUSHED OR PINNED. FAILURE TO
DO SO MAY RESULT IN SERIOUS INJURY OR DEATH.
1. Always disconnect power before servicing the keypad. Do not apply power until all connection
wiring is completed.
2.
The keypad must be properly grounded. Use a minimum 22AWG wire connected to the
common ground output. Failure to do so may damage the keypad.
3.
Allow at least 2ft (60cm) between this and any other keypads to avoid interference.
4.
All wiring and programming should be done by a professional installer to reduce the risk of
improper installation.
5.
The user’s guide for this keypad is located on pg. 34 of this manual.
6.
Be sure to store this manual in a safe place for future reference.

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
8SECO-LARM U.S.A., Inc.
Installation:
Key lock
Tamper screw
Inner back box
1. Unlock the keylock mounted on the face of the keypad with one
of the included keys.
2.
Remove the tamper screw from the bottom of the keypad with
the included security wrench.
3.
Open the faceplate of the keypad. The hinge will allow the
faceplate to hang open during installation.
4.
Remove the 1" wiring hole cover from the back of the keypad
housing.
5.
Install the keypad using the included mounting screws and
mounting screw anchors (if necessary).
NOTE: If attaching the keypad to a mounting plate, such as a
gooseneck stand, use the 4 mounting plate holes
located on the back of the keypad housing (see Fig. 1).
6.
Remove the inner plastic back box to access the terminals.
7.
Connect the wires to the keypad according to the wiring diagram (see "Wiring Diagram," pg.
9).
8.
Finish assembly by replacing the inner back box, closing and locking the keypad, and
replacing the tamper screw.
Fig. 1
These holes are used to
mount the keypad to a
gooseneck stand.

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
SECO-LARM U.S.A., Inc. 9
Wiring Diagram:
Connection Terminals
Terminal
Description
12~24 VAC/VDC
Connect to a 12~24 VAC/VDC
power supply. Observe polarity.
Output 1 N.C.
NO/NC/COM relay output,
Max. 5A@24VDC
Output 1 COM
Output 1 N.O.
Output 2 N.C.
NO/NC/COM relay output,
Max. 1A@24VDC
Output 2 COM
Output 2 N.O.
Egress Input
N.O. Pushbutton contact to
ground. Press button to activate
Output #1
Output 3 N.C.
NO/NC/COM relay output,
Max. 1A@24VDC
Output 3 COM
Output 3 N.O.
K or A output
Transistor ground output, max.
100mA@24VDC. See "K or A"
jumper information below for
programming details.
Duress output
Transistor ground output, max. 100mA@24VDC. Switches to ground (–) to trigger
a silent alarm or other device when a user enters a duress code.
Ground (–)
Common ground output.
Door Sensor
Connect to an optional N.C. sensor such as a magnetic contact to monitor if a
door is open or closed. Connect to ground (–) if not used.
Output 1 inhibit
Output #1 inhibitor. N.O. input, connect to Interlock Control of second keypad if
needed so that if one keypad is used to open a door, the other is temporarily
disabled.
Interlock Control
Interlock control. N.O. input, connect to Output 1 Inhibit of second keypad if
needed so that if one keypad is used to open a door, the other is temporarily
disabled.
Tamper N.C.
Tamper switch output, N.C. contact, max. 50mA@24VDC. Connect to the N.C.
24-hour protection zone of an alarm if needed.
Jumper Settings
Jumper
Position
Description
Backlit
Full
Dim backlit during standby. Full backlit for 10 seconds after any button press.
Auto
No backlit during standby. Full backlit for 10 seconds after any button press.
K or A
K
Switches to ground (–) for 10 seconds after any button press.
A
Switches to ground (–) when alarm occurs to trigger optional auxiliary alarm.
BACK-LIT
Jumper Positions
Backlit – Full
Backlit – Auto K or A – Keypress K or A – Alarm
FULL AUTO
BACK-LIT
FULL AUTO
K OR A
KEY ALARM
K OR A
KEY ALARM

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
10 SECO-LARM U.S.A., Inc.
Sample Applications:
Stand
-Alone Door Lock:
In this
application, the keypad is connected to a single door lock and an egress pushbutton.
12-24VDC
Power Supply
Egress button
(inside the protected premises)
Additional egress buttons can be
connected in parallel as needed
N.C. N.O.
OR
OUTPUT RELAY
N.O. Output for
Fail-secure Lock
N.C. Output for
Fail-safe Lock
N.O.
N.O.
(+)
(–)
(+)
(–)
Cathode
Diode 1N4004
(for DC use only)
Electric
Lock
12~24 VAC/VDC
Keypad #1
Keypad #2
Inter-Lock System Using Two Keypads:
In this application, two keypads are
each connected to separate door
locks and egress pushbuttons. While
one door
is open, the other cannot
be opened.
Use
an N.C. magnetic contact or
some
other N.C. device to detect
whether
a door is opened or closed.
Do this for the two doors being
protected.
RTE for
door #2
Door #1
Sensor
Door #2
Sensor
Diode 1N4004
(for DC use only)
RTE for
door #1
Diode 1N4004
(for DC use only)
12~24 VDC
Power Supply
Electric lock #2
Electric lock #1
12~24 VDC
Power Supply
N.C. N.O.
OR
N.C. N.O.
OR
12~24 VAC/ VDC
12~24 VAC/ VDC

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
SECO-LARM U.S.A., Inc. 11
Sample Applications (Continued):
Sample Applications for Auxiliary Terminals:
•Door Auto Relock – The system will immediately relock the door after the door is closed. This
prevents unwanted "tailgate" entries, which can happen if an unauthorized person tries to follow
an authorized person through the door.
•
Interlock Control – When the door is open, the Interlock Output will give a (-
) ground command
to disable the other keypad in an interlock system
•
Door-Forced-Open Warning – The keypad will beep and activate the alarm output whenever
the door is forced open without using a valid user code, card, or egress input (see
"Programming the Door-Forced-Open Warning and Timing," pg. 30).
•
Door-Propped-Open Warning – The keypad will beep whenever the door is open longer than
the programmed time (see "Programming the Door-Propped-Open Warning and Timing,"
pgs. 30~31).
•
Door Open Alarm – The keypad will beep and activate the alarm output whenever the door is
opened without using a valid user code or card (see "Programming the Door Open Alarm and
Timing," pg. 31).
Use a Normally Closed door position
sensor (usually a magnetic contact) on
the door to enable the use of the
following functions:
Door Sensor:
Magnetic
contact
2.
For N.O. locking devices, connect outputs
in parallel with locking device
Door-Hold-Open Mode:
1.
For N.C. locking devices, connectoutputs
in series with working device.
Diode 1N4004
(for DC use only)
Diode 1N4004
(for DC use only)
12~24 VDC
Power Supply
Electric lock
Electric lock
DC
DC
12~24 VDC
Power Supply
+
–
+
–
– +
– +

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
12 SECO-LARM U.S.A., Inc.
Sample Applications for Auxiliary Terminals (Continued):
Key Active Output:
Set the K or A jumper to "K" (see "Jumper Settings," pg. 9) to cause the Key Active Output to
switch to (
–) ground for 10 seconds whenever a key is touched. You may use it to turn on an LED
lamp and for a sma
ll buzzer to notify a guard, or to energize a relay to switch on lights or trigger a
CCTV Camera to start recording.
NOTES
:
•
Make sure that the relay for switching on lights has high enough isolation between high voltage
and low voltage to prevent damage of the keypad.
•
Only one connection option is recommended. Make sure the sink current does not exceed the
maximum rating of 100mA.
•
External power supply and isolation relay are strictly necessary in driving high power device,
such as lights.
Low power
piezo buzzer
1.5K
LED
OR
+12VDC
N.O. Relay
contact
+12VDC
Isolation relay
Alarm Control Panel
24-Hour
N.O. Protection
Zone
Set the K or A jumper to "A" (see "Jumper Settings," pg. 9) to cause the Alarm Output to switch to
(
–) ground in Door-Forced-Open or the Door Open after Egress Delay. You may use it to turn on
an LED lamp and/ or a small buzzer to notify a guard; or connect it to a 24
-hour Normally Open
protection zone of an alarm system. See "Programming the Door
-Forced-Open Warning and
Timing," pg.
30 and "Programming the Door Open Alarm and Timing," pg. 31.
NOTE:
Only one connection option is recommended. Make sure that the sink current does not
exceed the maximum rating of 100mA.
Alarm Output:
Low power
piezo buzzer
1.5K
LED
OR
+12VDC

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
SECO-LARM U.S.A., Inc. 13
Getting Ready to Program:
Sample Applications for Auxiliary Terminals (Continued):
Codes and/or Cards:
The keypad can
be set to be activated by users in one of three ways:
1.
Keypad code only – There are five types of keypad codes:
•Master programming code – Used only for entering programming mode; there can be only
one master programming code per keypad.
•Super user code – Can be used to activate outputs #1, #2, and #3 to disable (inhibit) or
enable the operation of the outputs.
•User codes – Unique codes for each user to activate outputs #1, #2, or #3.
•Visitor codes – Temporary user codes that can be assigned to visitors or temporary workers
to activate output #1; the visitor codes can be programmed for one-time use
or to expire after
a set number of hours has passed.
•Duress codes – Assigned to specific users as a way to send a silent alert if forced to use the
keypad under duress.
2.
Proximity card only – Standard 125kHz (EM125) proximity cards can be used to activate
outputs #1, #2, or #3.
3.
Card + code – For enhanced security, the user can be required to also enter a code after
tapping a proximity card. The code may be unique to each card or to a group of users, or a
common code can be used with all cards.
Duress Output:
The Duress Output switches to (–) ground when a duress code is entered. You may use it to turn
on an LED lamp and/ or a small
buzzer to notify a guard; or connect it to a 24 hour Normally Open
protection zone of an alarm system.
NOTE:
Only one connection option is recommended. Make sure that the sink current does not
exceed the maximum rating of 100mA.
Low power
piezo buzzer
1.5K
LED
OR
+12VDC
Alarm Control Panel
24-Hour
N.O. Protection
Zone

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
14 SECO-LARM U.S.A., Inc.
Getting Ready to Program (Continued):
Security Levels:
There are four possible security levels for the keypad:
1.
Card only – The most basic, convenient level of security. Hold a previously-programmed
proximity card over the keypad to activate outputs #1, #2, or #3 (see "Programming User
Codes and Proximity Cards," pgs. 20~21).
2.
User code only – Type in a 4- to 8-digit user code to activate outputs #1, #2, or #3 (see
pgs. 20~21).
3.
Card + common user code – All valid proximity cards can be programmed with a single
common user code so that outputs #1, #2, or #3 can only be activated if one of the cards and
the common user code are used together. The common user code is automatically assigned
when each proximity card is programmed into the keypad (see "Programming Common User
Codes," pg. 19).
4.
Card + unique user code – The most secure level. Each proximity card can be programmed
with its own unique user code so that outputs #1, #2, or #3 can only be activated if the card
and the unique code are used together (see pgs. 20~21).
Power Up the Keypad:
When the
keypad is first powered up, it will beep continuously for about 1 minute. During this
power
-up time, if needed, use Direct Access to Programming (DAP) to reset the master
programming
code (see "Direct Access to Programming (DAP),” pg. 33).
1.
Turn off the beeping before the 1-minute power-up period ends:

This will immediately stop the beeping. When the beeping has ended, the keypad is ready for
normal operation or for programming.
Enter and Exit Programming Mode:
All
programming of the keypad is done in programming mode.
1.
Enter programming mode:

NOTE:  is the master programming code.  is the default master
programming code (see "Programming the Master Programming Code," pg. 17 to
program a new master programming code). The amber LED will tur
n to a steady ON to
indicate that the keypad is in programming mode.

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
SECO-LARM U.S.A., Inc. 15
Getting Ready to Program (Continued):
System Restore:
System restore will reset all programming values except the master programming code back to
default values shown on
pg. 16.
1.
Make sure the keypad is in programming mode (see "Enter and Exit Programming Mode,"
pgs. 14~15):
2.
Initiate system restore:

NOTE
S:
•
System restore will reset ALL programming except the master programming code back to default
values. Be careful to use system restore only when absolutely necessary.
•
System restore may take several minutes. The amber LED will flash rapidly during thistime.
•
Once system restore has been completed, the keypad will beep twice to show that all
programming values have been reset to their default values and are ready to be re-programmed.
•
At this point, the keypad is still in programming mode.
2. Exit programming mode:

The  entry can be used to exit programming mode at any time while programming. The
amber LED will return to flashing, indicating standby mode, upon exiting programming mode.
NOTE: DO NOT DISCONNECT THE KEYPAD FROM POWER WHILE IN PROGRAMMING
MODE. Disconnecting the keypad while in programming mode could cause a keypad
memory error.

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
16 SECO-LARM U.S.A., Inc.
Programming Format and Default Programming Values:
In this manual, the format used for programming the keypad is as follows:
•A 2-digit (  ) FUNCTION identifier to tell the keypad what is being programmed.
•A varying number of digits ( ) to represent the parameters of that FUNCTION.
•The key to confirm programming of the FUNCTION.
The following is a list of the different programming functions:
Function
Parameters
Default Functions and Values
Page #
01
Master programming code
Default 0000, code length from 4~8 digits
17
02
Super user code
No default, must be programmed
17~19
03
Common user code for output #1
No default, must be programmed
19
04
Common user code for output #2
No default, must be programmed
19
05
Common user code for output #3
No default, must be programmed
19
10
User codes/cards for output #1
No default, must be programmed
20~21
20
User codes/cards for output #2
No default, must be programmed
20~21
30
User codes/cards for output #3
No default, must be programmed
20~21
40
Visitor codes for output #1
No default, must be programmed
22
41
Duress codes for output #1
No default, must be programmed
23~24
42
Duress codes for output #2
No default, must be programmed
23~24
43
Duress codes for output #3
No default, must be programmed
23~24
51
Output mode for output #1
5-Second output, momentary
25
52
Output mode for output #2
5-Second output, momentary
25
53
Output mode for output #3
5-Second output, momentary
25
55
System real-time clock
No default, must be programmed
26
56
Output #1 auto-disable time
No default, must be programmed
26~27
60
Wrong-code system lock-up
Locks keypad after 10 false code/card tries
28
70
User code entry mode
Manual entry of “#” after each code
28~29
71
Keypad sounds
Programming and operation beeps enabled
29
72
Output relay activation sounds
1-Second beep when output is activated
29
73
Amber LED standby flashing
Center LED flashes on standby
29
80
Door-forced-open warning
Warning disabled
30
81
Door-propped-open warning
Warning disabled
30~31
90
Egress delay/warning
Egress output happens immediately
31~33
91
Door open alarm and timing
Alarm output is disabled
31
NOTE: The Direct Access to Programming (DAP) code 2828 (pg. 33) and the system restore code
9999 (pg. 15) are fixed and cannot be changed, even via programming.

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
SECO-LARM U.S.A., Inc. 17
Programming the Master Programming Code:
Programming the Super User Code:
The super user code has multiple functions:
•
The super user code can activate or deactivate outputs #1, #2, or #3 at any time.
•
The super user code can toggle output #1 on or off.
•
The super user code can pause or restart the timed output #1 auto-disable period.
•
The super user code can enable or disable output #1.
•
The super user code is exempt from any system inhibition or lockup functions. It is valid at any
time.
Programming the Super User Code:
1.
Make sure the keypad is in programming mode (see "Enter and Exit Programming Mode,"
pgs. 14~15):
2.
Enter the new super user code:

NOTES:
•represents the new super user code, which can be 4 to 8 digits long.
•There can be only one super user code for the keypad.
•Programming a new super user code will overwrite the previous super user code.
•The master programming, super user, common user, visitor, duress, and user codes
cannot be the same.
The master programming code is used to enter programming mode. The master programming
code
does not serve as a user code for activating outputs #1, #2, or #3.
1.
Make sure the keypad is in programming mode (see "Enter and Exit Programming Mode,"
pgs. 14~15):
2.
Enter the new master programming code:

NOTES:
•
represents the new master programming code, which can be 4 to 8 digits long.
•
There can be only one master programming code for the keypad.
•
Programming a new master programming code will overwrite the previous master programming
code.
•
The master programming, super user, common user, visitor, duress, and user codes
cannot be the same.
•
If the keypad is set for Auto Code Entry Mode, all codes will need to be the same number of
digits as the master programming code (see "Programming the User Code Entry Mode,"
pgs. 28~29).

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
18 SECO-LARM U.S.A., Inc.
Programming the Super User Code (Continued):
Deleting the Super User Code:
This function is useful for protecting the premises in case
the super user code is forgotten.
To delete a super user code:
1.
Make sure the keypad is in programming mode (see pgs. 14~15):
2.
Enter:

Using
the Super User Code:
In these examples, assume the super user code is
.
1.
Activate or deactivate output #1 (timed or toggle, depending on programming):

2.
Activate or deactivate output #2 (timed or toggle, depending on programming):

3.
Activate or deactivate output #3 (timed or toggle, depending on programming):

4.
To toggle operation of output #1 ON or OFF:

NOTES:
•This function is used to leave output #1 active for extended periods of time.
•Do not forget to deactivate this function after its use is no longer required.
•It is recommended to only use this function with fail-safe locks.
5.
Temporarily pause or restart the timed output #1 disable period:

NOTES:
•This function is used to enable the operation of output #1 if it was disabled using the
output #1 auto-disable function (see pgs. 26~27).
•When the output #1 auto-disable function is inactive, the red LED will flash steadily. This
indicates that output #1 may now be used.

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
SECO-LARM U.S.A., Inc. 19
Programming Common User Codes:
Programming the Super User Code (Continued):
NOTE: This function is only used when utilizing proximity cards. For programming user codes,
see pgs. 20~21.
This function allows a common user code to be automatically added to each proximity card as it
is
programmed. Every proximity card user also uses the same common user code to operate outputs
#1, #2, or #3
.
This provides greater security than programming the keypad to operate with the card
alone. It is also more convenient than assigning each user a
unique user code, although unique
user codes offer an even greater degree of security.
1.
Program a common user code for output #1:

2.
Program a common user code for output #2:

3.
Program a common user code for output #3:

4.
Delete a common user code for output #1:

NOTE
S:
•
 represents the new common user code, which can be 4 to 8 digits long.
•
Programming a new common user code will overwrite the previous common user code.
•
A common user code is not necessary if unique user codes are assigned.
•
The master programming, super user, common user, visitor, duress and user codes
cannot be thesame.
6. Disable or enable output #1 (toggle, regardless of programming):

NOTES:
•For more information on programming timed or toggle mode, see "Programming the Output
Mode and Output Timing," pg. 25.
•The left LED will remain red while output #1 is disabled.
•For safety reasons, the egress button works regardless of whether output #1 is enabled or
disabled via the super user code.
•The super user code continues to operate output #1 even while that output is disabled.

ENFORCER Heavy-Duty Outdoor Access Control Keypad with Proximity Reader
20 SECO-LARM U.S.A., Inc.
Programming User Codes and Proximity Cards:
When programming user codes and/or proximity cards, use this general formula:

– Output
– Security Level (or to delete a user code or card)
– User ID
– User Code / Proximity Card
Outputs:
•
 – Output #1, up to 1,000 possible user codes and proximity cards.
•
 – Output #2, up to 100 possible user codes and proximity cards.
•
 – Output #3, up to 100 possible user codes and proximity cards.
Security Levels and Card/Code Deletion:
•
Card only – The most basic, convenient level of security. Just tap a previously-programmed
proximity card over the keypad to activate outputs #1, #2, or #3.
NOTE: The duress code feature cannot be used with the keypad programmed to "card only"
security mode. However, a duress code can be entered instead of a card.
•
User code only – Type in a 4 to 8-digit user code to activate outputs #1, #2, or #3.
•
Card + unique user code – The most secure level. This code is programmed separately for
each card and can be unique to the card, or the same code can be used for a group or
department. The card and code must be used together to operate the output.
•
Card + common user code – All valid proximity cards can be programmed with a single
common user code so that outputs #1, #2, or #3 can only be activated if one of the cards and the
common
user code are used together. The common user code is automatically assigned as each
proximity card is programmed into the keypad.
•
– Delete a programmed proximity card or user code.
•
 – Delete all programmed proximity cards or codes for the selected output.
User IDs:
•
 to  – 1,000 unique user IDs for user codes and proximity cards for output #1.
•
 to  – 100 unique user IDs for user codes and proximity cards for output #2.
•
 to  – 100 unique user IDs for user codes and proximity cards for output #3.