ENFORCER SA-027WQ User manual

The ENFORCER SA-027WQ 7-Day Timer can be programmed o opera e wo Form C relays 24
hours a day on a weekly basis for various applica ions including securi y, access con rol, ligh ing,
and environmen al con rol. Each relay can be programmed for up o 60 even s wi h each even on
a weekly or daily schedule. A programmable holiday disables he imer for a single day weekly.
•Wide opera ing vol age range – 10~48 VDC, 12~24 VAC
•Two N.O. or N.C. Form C relays, 10A@14VDC, wi h one egress inpu per relay
•60 Programmable even s per relay ( o al of 120) se weekly, daily, or hourly, over a week
•Programmable holiday even – holiday from 1~31 days in dura ion
•EEPROM Memory for safe da a pro ec ion in case of power failure
•No clock ba ery o replace - buil -in super capaci or saves da e/ ime 7-10 days af er power loss
•Smar backup ba ery charger for ex ernal backup ba ery (no included) ex ends ba ery life
•Easy roubleshoo ing s a us checks – relay es , inpu vol age, backup ba ery vol age/charge
•Tandem mode allows bo h relays o opera e simul aneously
•Passcode pro ec ion can be urned ON or OFF
•Firs -person-in (firs -man-in, FM) func ion in errup s he normal opera ion of he imer
•Even ou pu s can be programmed o disable, ON, OFF, shun , or momen ary (1~99 seconds)
•Enable/Disable 1-hour offse as a quick se ing during Dayligh Savings Time
•Alphanumeric whi e backli LCD display for easy programming
7-Day Timer
SA-027WQ
Installation Manual

ENFORCER 7-Day Timer
2 SECO-LARM U.S.A., Inc.
Table of Contents
Parts List ........................................................ 2
Overview ......................................................... 2
Specifications ................................................ 3
Installation ...................................................... 3
Basic Wiring ................................................... 4
Sample Application ....................................... 4
Programming Introduction ...........................
Programming Recommenda ions .................. 5
LCD Display ................................................... 5
Programming Bu ons .................................... 5
Programming Menu Flow Char ..................... 6
Programming ................................................. 6
Se ing he Display Con ras .......................... 7
Se ing he Day and Time ............................... 7
Programming Even s ...................................... 8
Programming a Holiday Even ........................ 9
Programming Dayligh Savings Time ............. 9
Programming a PIN Code ............................ 10
Programming Relays in Tandem .................. 10
Performing a Sys em Tes ............................ 11
Clearing he Memory .................................... 11
Smart Charging ............................................ 12
Checking Power Inpu and Backup Ba ery
Level .......................................................... 12
Troubleshooting ........................................... 12
Parts List
1x
Timer
2x
Mounting screws
2x
Wires for optional backup battery
1x
Manual
Overview
4
1
/
16
" (105mm)
LCD Display
Terminal screw
access slo
Relay
indica ors
Terminal Layout Chart (lef o righ )
Programming
bu ons
5
9
/
16
"
(76mm)
1
1
/
16
"
(33mm)
9.
Ground inpu
10. Firs person (FM) 1 – N.O. inpu
11. Relay 2 – N.O. ou pu
12. Relay 2 – COM ou pu
13. Relay 2 – N.C. ou pu
14. Egress 2 – N.O. inpu
15. Ground inpu
16. Firs person (FM) 2 – N.O. inpu
1.
Power inpu
2. Power inpu
3. Backup ba ery +
4. Backup ba ery –
5. Relay 1 – N.O. ou pu
6. Relay 1 – COM ou pu
7. Relay 1 – N.C. ou pu
8. Egress 1 – N.O. inpu

ENFORCER 7-Day Timer
SECO-LARM U.S.A., Inc. 3
Specifications
Operating voltage 10~48 VDC / 12~24 VAC
Number of relays 2 Form C
Relay contact rating 10A@14VDC
Relay active current draw 110mA@12VDC ±10% (per channel)
Standby current draw 14mA@12VDC ±10%
Backup battery type 12VDC (suppor s lead-acid compa ible ba ery, no included)
Battery charge Smar charge, 50mA max., when ba ery is ≥11.5V and ≤12.8V
Event capacity 60 per relay
Operating temperature -4°~167° F (-20°~75° C)
Dimensions 41/8"x3"x15/16" (105x76x33 mm)
Weight 5.6-oz (158g)
Installation
1. Find a loca ion where he LCD display is visible, and he bu ons accessible. Mark he loca ion.
2. Connec he wires (see Overview, Terminal Layout Chart, pg. 2 and Basic Wiring, pg. 4).
3. Connec a 12~24 VAC or 10~48 VDC power supply o he power inpu erminals, 1 and 2.
4. Connec he 12VDC ba ery backup o he backup ba ery inpu erminals 3 (+) and 4 (–) if
desired (no included).
5. Connec he devices ha are being con rolled o he ou pu s of relays 1 and/or 2 as well as any
o her devices being connec ed.
NOTE: To pro ec he relay, you mus ins all a 1N4004 diode—wi h he ca hode (s riped
end , no included) wired oward he posi ive side—in parallel wi h he
power supply and as close o he lock as possible for DC powered locks unless your
lock has a diode built in. AC powered locks and elec romagne ic locks require a
varis or/MOV (05D390K or similar, no included) wired in he same loca ion if the lock
does not have one built in (all SECO-LARM elec romagne ic locks have buil -in
pro ec ion). Failure o use hese as direc ed will void he warran y.
6. Close he case and moun he uni o he loca ion marked above.

ENFORCER 7-Day Timer
4 SECO-LARM U.S.A., Inc.
Basic Wiring
NOTES
•When connec ing o a backup ba ery, he ba ery vol age mus be 12VDC ONLY.
•Only a ba ery can be connec ed o he backup ba ery inpu . Do no connec a power adap er.
•When i s op ional N.O. swi ch is ac iva ed, he first person-in (firs -man-in, FM) func ion
suspends he imer opera ion. If he corresponding relay is urned on before first-person-in is
ac iva ed, he relay remains on un il he first-person-in swi ch is deac iva ed. Once deac iva ed,
he imer will urn on he las programmed func ion prior o he first-person-in ac iva ion.
Sample Application
1
An RF receiver can be used o rigger he egress wirelessly. The receiver’s COM erminal is connec ed o a ground and he N.O. erminal is
connec ed o he imer's egress inpu . A second ou pu on he RF can be connec ed o he first-person-in (firs -man-in, FM) erminal.
2
A compa ible RF ransmi er can hen be used o rigger he egress, via he RF receiver and he first-person-in (firs -man-in, FM) func ion.
3
A ga e opera or connec ed o he relay ou pu is riggered and opens a ga e.
Power
–
in +
1
2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
Backup
–
ba ery +
N.C.
Relay 1 COM
N.O.
N.C.
Relay 2 COM
N.O.
Egress 1
Egress 2
(Firs person)
FM 2
Ground
(Firs person)
FM 1
Ground
PUSH
TO
EXIT
Ga e opera or
3
Power supply
12~24 VAC or
10~48 VDC
–
+
Bell
+
RF receiver
1
2- Bu on
RF ransmi er
2
Shun swi ch
Backup ba ery
12VDC
–
–
+
+
–
Power
–
in +
1
2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
Backup
–
ba ery +
N.C.
Relay 1 COM
N.O.
N.C.
Relay 2 COM
N.O.
Egress 1
Egress 2
(Firs person)
FM 2
Ground
(Firs person)
FM 1
Ground
Power supply
12~24 VAC or
10~48 VDC
Backup ba ery
12VDC
–
+
N.O. Ground swi ch
Device 2
Device 1
N.O. Ground swi ch

ENFORCER 7-Day Timer
SECO-LARM U.S.A., Inc. 5
Programming Introduction
A convenien fea ure is he abili y o program i before ins alla ion. The EEPROM memory s ores
and pro ec s programming ins ruc ions even during a power failure and he super capaci or, af er a
full charge (abou 24 hours), will preserve he da e and ime for 7~10 days af er power is los .
Programming is easier and fas er if you know exac ly how you wan o use he imer and have a
good unders anding of he func ions i has.
Programming Recommendations
1. I is recommended ha you follow he programming ins ruc ions in he order given as his will
make he ins alla ion easier.
2. De ermine which relays will opera e he devices ha will be con rolled.
3. De ermine whe her wo relays will be used in andem.
4. Using a separa e piece of paper, wri e down your programming no es.
a. Any even s ha can be block coded. i.e., even s ha occur in a pa ern.
b. All he even s you wan o program, as well as heir dura ion (up o 60 per relay).
c. Any holiday you wish o program o override he programmed even s.
5. Decide whe her you wan o use a PIN code or no . See rogramming a IN Code on pg. 10.
LCD Display
Besides he obvious ex en ries, here are some abbrevia ions or icons ha should be no ed.
NOTE: OFF or ON in he op righ corner of he screen refers o he relay s a us. OFF means ha
nei her relay is riggered. If ei her relay is on, he display will change o ON.
Programming Buttons
Programming is accomplished wi h wo bu ons.
1. SEL – The Select bu on is used o naviga e he menu o selec he func ion o be programmed.
2. ENTER – When a choice has been selec ed, he Enter bu on is used for changing and
confirming an op ion. Pressing once will change o he nex op ion. Pressing and holding will
cycle ahead rapidly, handy for number op ions when you need o skip much fur her ahead.
Indica es backup ba ery is charging
Indica es Dayligh Savings Time is ac iva ed
Indica es device is locked wi h PIN code
Re urn o paren menu

ENFORCER 7-Day Timer
6 SECO-LARM U.S.A., Inc.
Programming Introduction (Continued)
Programming Menu Flow Chart
When you firs apply power o he imer, you will see a s ar up screen for abou 3 seconds followed
by a home screen showing he day and ime (which you will se la er). Repea edly pushing he SEL
bu on will hen ro a e you hrough he basic programming menus as shown below.
Programming
The basic s eps for programming are as follows.
1. Go o he menu for he fea ure you wish o program by pressing he SEL bu on.
2. Press he ENTER bu on o en er ha menu.
3. The firs programming op ion will be flashing. Press he ENTER bu on o change ha op ion
and press he SEL bu on o move o he nex op ion and repea .
4. Move o he Return icon and press he ENTER bu on o save your changes and exi o he
home screen.
NOTES:
•In he ins ruc ions below, he PIN Code will be assumed o be disabled. If enabled, you'll need o
en er your PIN code before beginning programming.
•Holding he ENTER bu on down will cause i o quickly move hrough he op ions.
Screen Readout Description
Set Events
ENTER o se imed even s (up o 60 per relay) including even number,
relay number, how he relay will opera e, and he day and ime he even is
scheduled. Block programming for even s is also available.
Set Holidy
ENTER o program a holiday even , i.e., a day when he normal opera ion
of he imer should be suspended.
Set PinCode
ENTER o se a PIN code o secure he imer from unau horized ampering
(op ional, 4-digi s, fac ory prese = 0000).
Set Time
ENTER o se bo h he curren day and ime (using 24-hour, mili ary ime
forma ).
Set DST
ENTER o enable/disable Dayligh Savings Time – Disable (S andard ime)
or Enable (Add 1hr)
Systm Test
ENTER o show he curren s a us of bo h relays, whe her on or off and o
es he opera ion of each relay.
Set Disply
ENTER o adjus he con ras of he display using rela ive numbers 00~09.
Set Tandem
ENTER o enable or disable he wo relays o rigger oge her in andem.
Clr Memory
ENTER o clear all programmed i ems excep he PIN code from he
memory. You will be required o confirm yes or no.
Exit
ENTER o exi programming mode and re urn o he home screen.
SEL

ENFORCER 7-Day Timer
SECO-LARM U.S.A., Inc. 7
Programming (Continued)
Setting the Display Contrast
NOTES
•The con ras is represen ed rela ively from 00~09 (defaul , 00). Con inuing o press ENTER af er
reaching 09 will s ar he cycle over a 00.
•The display con ras can also be se a any ime by pressing and holding he SEL and ENTER
bu ons a he same ime. The screen con ras will gradually adjus . If you con inue o hold hem,
he con ras se ings will cycle back o 00 and s ar over. When i reaches he level ha you
desire, release he bu ons.
Setting the Day and Time
NOTE: The ime is displayed in 24-hour, mili ary forma where 1:00 PM is wri en as 13:00:00.
Press ENTER o see he
following.
Set STD Time
>SUN< 13:1 :17
The day will be flashing.
Press ENTER o change.
Press SEL o accep and
move o he
nex op ion and
repea .
Keep pressing SEL o
cycle
hrough and correc errors or
o go o he return icon .
Press ENTER a he o
re urn o he home screen.
Press SEL un il
>S e t Ti m e <
appears.
Press ENTER o see he
following.
Set Contrast
>00<
The
00
will be flashing.
Con inue o press ENTER
un il he desired con ras is
reached.
When sa isfied, press SEL
o move o he return icon.
Set Contrast
>00<
Press ENTER a he o
re urn o he home screen.
Press SEL un il
>Set Disply <
appears.

ENFORCER 7-Day Timer
8 SECO-LARM U.S.A., Inc.
Programming (Continued)
Programming Events
NOTE: Relay opera ions are Dis (shun ), ON, =x (momen ary, where x=01~99 seconds), or OFF.
Press ENTER o see he
following.
>R1<01 Dis
_______ 13:1
Choose he relay (
R 1
).
Press ENTER o change,
SEL o accep and move on.
Choose even (
0 1
, 01~60).
Press ENTER o change,
SEL o accep and move on.
Selec relay opera ion (
D i s
)
.
Press ENTER o change,
SEL o accep and move on.
Dis, ON, OFF
Press SEL un il
>Set Events <
appears.
Press ENTER o change
he
day shown, SEL o accep
and move on.
>_______ 08:29
All
Press ENTER
o change he
rigger ime, SEL o accep
and move on.
_M_W_F_ >08:29
All
Press ENTER o change
dura ion (01~99 sec), SEL
o accep and move on.
t=01
t=01
Keep pressing SEL o cycle
hrough and correc errors or
o go o he return icon .
All
Press ENTER a he o
re urn o he home screen.
All

ENFORCER 7-Day Timer
SECO-LARM U.S.A., Inc. 9
Programming (Continued)
Programming a Holiday Event
NOTES
•In programming holidays, 00 is equivalen o "disable."
•No e ha holiday even s are for 24-hour periods beginning a midnigh and canno be limi ed o
cer ain hours.
•On a holiday, he lower por ion of he imer display will al erna e be ween he da e and
>HOLI
.
Programming Daylight Savings Time
NOTE: DST op ions are as shown below.
•Disable – S andard ime
•Enable – Adds one hour
Press ENTER o see he
following.
S e t D S T
>Disable▓<
Press ENTER o enable,
SEL o accep and move o
he return icon .
Keep pressing SEL o
cycle
hrough and correc errors or
o go o he return icon .
Press SEL un il
>S e t D S T <
appears.
Press ENTER a he o
re urn o he home screen.
Press ENTER o see he
following.
Holiday
>Sun< 00 days
Choose he day (
S u n
).
Press ENTER o change,
SEL
o accep and move on.
Move o he following (
0 0
,
00~31) o se he # of days.
Sun >00<days
Keep pressing SEL
o cycle
hrough again or go o he
icon o press ENTER o
re urn o he home screen.
Press SEL un il
>Set Holidy <
appears.

ENFORCER 7-Day Timer
10 SECO-LARM U.S.A., Inc.
Programming (Continued)
Programming a PIN Code
If you forge he PIN Code, proceed as follows o unlock he imer and en er programming mode.
1. Turn off power o he imer and disconnec he backup ba ery.
2. Power up he imer and immedia ely press and hold he ENTER bu on for a leas 3 seconds,
un il he lock icon disappears from he display. This re urns he PIN code o 0000.
3. Proceed wi h programming as usual.
Programming Relays in Tandem
Press ENTER o see he
following.
Set Tandem
>Disable<
Press ENTER o change
enable/disable, SEL o
accep and move o .
Keep pressing SEL o
cycle
hrough and correc errors or
o go o he return icon .
Press SEL un il
>Set Tandem <
appears.
Press ENTER a he o
re urn o he home screen.
Press ENTER o see he
following.
Set Pin
>0000< Disable
Press ENTER o change
he
firs digi (0~9), SEL o
accep and move o he nex
.
Repea for each digi .
Press
SEL
a he las digi o move
o he enable/disable.
Press ENTER o change
enable/disable, SEL o
accep and move o .
>0000< Disable
Press SEL un il
>Set PinCode <
appears.
Keep pressing SEL
o cycle
hrough again or go o he
icon o press ENTER o
re urn o he home screen.