Entrematic Ditec LOGIC M User manual

Ditec LOGIC M
Control panel installation manual for 230 V~ automation with
one or two motors
www.ditecentrematic.com
IP1854EN
TM
AUX AUX
JR6
POWER
SA
IN
11
12
F1
F2
TC RP TR R1
OM J7
15141312110011234567892041UWV X Z YLN
LN
com com
Electric lock
Power suuply
Flashing light
Lamp
Limit switch Limit switch
Accessories output
Automatic closing
Opening
Closing
Step by step
Opening safety device
Closing safety device
Safety reopening
Stop
Partial opening
Safety test
M1
1~
M2
1~
D5 S5 JT
NIO
SO
JR10
JR4
EO
1
ON
23456
F
U
S
E
F
U
S
E
LOGICM
RF
CT12345

24
IP1854EN - 2015-04-17

25
IP1854EN - 2015-04-17
Index
Subject Page
1. General safety precautions 26
2. EC declaration of conformity 27
3. Technical data 27
3.1 Applications 27
4. Commands 28
4.1 Self-controlled safety edge 29
5. Outputs and accessories 29
6. Adjustments 31
6.1 Trimmer 31
6.2 Dip-switch 31
6.3 Jumper 32
6.4 Signals 32
7. Start-up 33
8. Troubleshooting 34
9. Example application for two-motors swing gates 35
10. Example application for one-motor swing gate 37
11. Example application for sliding gate 39
12. Example application for barrier 39
13. Example of parallel 40
Caption
i
This symbol indicates informations which are useful for correct product function.
This symbol indicates instructions or notes regarding safety issues which require particular attention.

26
IP1854EN - 2015-04-17
1. General safety precautions
This installation manual is intended for qualified personnel only.
Installation, electrical connections and adjustments must be performed in accordance
with Good Working Methods and in compliance with applicable regulations.
Before installing the product, carefully read the instructions. Bad installation could be hazard-
ous.
The packaging materials (plastic, polystyrene, etc.) should not be discarded in the environ-
ment or left within reach of children, as these are a potential source of hazard.
Before installing the product, make sure it is in perfect condition.
Do not install the product in an explosive environment and atmosphere: gas or inflammable
fumes are a serious hazard risk.
Before installing the motors, make all structural changes relating to safety clearances and
protection or segregation of all areas where there is risk of being crushed, cut or dragged, and
danger areas in general.
Make sure the existing structure is up to standard in terms of strength and stability. The motor
manufacturer is not responsible for failure to use Good Working Methods in building the frames
to be motorized or for any deformation occurring during use.
The safety devices (photocells, safety edges, emergency stops, etc.) must be installed taking
into account: applicable laws and directives, Good Working Methods, installation premises,
system operating logic and the forces developed by the motorized door.
The safety devices must protect any areas where the risk exists of being crushed, cut or gragged,
or where there are any other risks generated by the motorized door.
Apply hazard area notices required by applicable regulations.
Each installation must clearly show the identification details of the motorized door.
When necessary, connect the motorized door to a reliable earth system made in accordance
with applicable safety regulations.
During installation, maintenance and repair, interrupt the power supply before opening the lid
to access the electrical parts.
The protective casing of the automation must be removed by qualified personnel only.
To handle electronic parts, wear earthed antistatic conductive bracelets. The motor manu-
facturer declines all responsibility in the event of component parts being fitted that are not
compatible with the safe an correct operation.
For repairs or replacements of products only original spare parts must be used. The installer
shall provide all information relating to automatic, manual and emergency operation of the
motorized door, and provide the user with operating instructions.

27
IP1854EN - 2015-04-17
The manufacturer Entrematic Group AB with headquarters in Lodjursgatan 10, SE-261 44
Landskrona, Sweden
declares that the control panel Ditec LOGICM is in conformity with the provisions of the following
EC directives:
EMC Directive 2004/108/CE;
Low Voltage Directive 2006/95/CE.
Landskrona,29-01-2013 MarcoPietroZini
(President & CEO)
2. EC Declaration of conformity
3. Technical data
LOGICM LOGICMJ
Power supply 230 V~ 50/60 Hz 120 V~ 60 Hz
F1 fuse F6,3A F6,3A
F2 fuse F3,15A F3,15A
One motor output 230 V~ 5A max 120 V~ 6,3A max
Two motor output 230 V~
2x2,5A max
120 V~
2x3,15A max
Accessories power
supply 24 V 0,5 A 24 V 0,5 A
Temperature min -20 °C max +55 °C min -20 °C max +55 °C
Degree of protection IP55 IP55
Dimensions 187X261X105 187X261X105
3.1 Applications
i
NOTE: the given operating and performance features can only be guaranteed with the use of DITEC
accessories and safety devices.

28
IP1854EN - 2015-04-17
4. Commands
Command Function Description
1 2 N.O. AUTOMATIC
CLOSING
Permanently closing the contact enables automatic closing.
1 3 N.O. OPENING The opening operation starts when the contact is closed.
1 4 N.O. CLOSING The closing operation starts when the contact is closed.
1 5 N.O. STEP-BY-STEP With D5=ON closing the contact starts a sequential opening or clo-
sing operation: open-stop-close-open.
With D5=OFF closing the contact starts a sequential opening or clo-
sing operation: open-stop-close-stop-open.
Note: if automatic closing is enabled, with S5=ON the stop is not
permanent but at a time that is set by the TC, with S5=OFF the stop
is permanent.
41 6 N.C. OPENING SAFETY
DEVICE
Opening the safety contact stops the current opening operation in
progress and impedes any future opening operations.
41 7 N.C. CLOSING SAFETY
DEVICE
Opening the safety contact stops the current closing operation in
progress and impedes any future closing operations.
41 6
7
N.C. SAFETY STOP Opening the safety contact stops and prevents any movement.
Note: it does not carry out the disengagement operation. Use with
photocells installed only.
41 8 N.C. REVERSAL
SAFETY
DEVICE
Opening the safety contact triggers a reversal of motion (re-opening)
during a closing operation.
1 9 N.C. STOP Opening the safety contact stops the current operation.
1 9 N.C. EMERGENCY
STOP
To enable the emergency stop function (e.g. with a specific red but-
ton), connect the opening and closing controls to terminal 9 instead
of 1 (9-3, 9-4, 9-20).
1 9 N.O. HOLD-TO-RUN
FUNCTION
Permanently opening the safety contact enables the operator pre-
sence dependent function.
In this state, the opening (1-3, 1-20) and closing (1-4) controls fun-
ction only if held in the pressed position and the automation stops
when the controls are released.
All safety switches, the step-by-step control and the automatic clo-
sing function are disabled.
1 20 PARTIAL
OPENING
Closing the contact activates a partial opening operation of the door
wing powered by motor 1, of the duration set with the RP trimmer.
Once the automation stops, the partial opening control performs the
opposite operation to the one performed before stoppage.
0 11 N.C. M2 LIMIT SWITCH With TC=MAX, the limit switch contact opening stops closing move-
ment of motor 2 (M2).
With OM=OFF (1 motor mode) and DIP2=OFF, the limit switch stops
closing movement of motor 1 (M1).
With OM=OFF (1 motor mode) and DIP2=ON, the limit switch stops
opening movement of motor 1 (M1).
0 11 N.O. M2 PROXIMITY
LIMIT SWITCH
See Chapters 9-10, example 4.
0 12 N.C. M1 LIMIT SWITCH With TC=MAX, the limit switch contact opening stops closing move-
ment of motor 1 (M1).
With OM=OFF (1 motor mode) and DIP2=OFF, the limit switch stops
opening movement of motor 1 (M1).
With OM=OFF (1 motor mode) and DIP2=ON, the limit switch stops
closing movement of motor 1 (M1).
0 12 N.O. M1 PROXIMITY
LIMIT SWITCH
See Chapters 9-10, example 4.
WARNING: Make a jumper on all N.C. contacts if not in use. The terminals with the same number are equal.

29
IP1854EN - 2015-04-17
5. Uscite e accessori
Output Value - Accessories Description
01
+-
24 V 0,5 A
Accessories power supply.
Power supply output for external accessories, including automation
status lamp.
NOTE: the maximum absorption of 0.5 A corresponds to the sum of
all terminals 1.
AUX SOFA1-SOFA2
GOPAV
The control panel has two spaces for coupling board, type radio recei-
vers, magnetic loops etc.
The coupling board working mode is selected by DIP1.
WARNING: the plug-in cards must be inserted and removed with the
power supply disconnected.
11 ... 124 V 3 W
Automation open lamp.
Only with limit switch 0-11 (NC) connected and in one motor mode
(jumper OM=OFF) will the lamp extinguish when automation is closed.
12 ... 124 V 3 W
Automation closed lamp.
Only with limit switch 0-12 (NC) connected and in one motor mode
(jumper OM=OFF) will the lamp extinguish when automation is open.
13 ... 124 V 3 W
Automation open lamp.
A lamp lights up that extinguishes only when automation is closed.
14 ... 0LAMPH
24 V 50 W
Flashing light.
Activated during opening and closing operations.
4.1 Self-controlled safety edge SOFA1-SOFA2 or GOPAVRS
Command Function Description
GOPAV
SOFA1-SOFA2
SAFETY TEST Place the SOFA1-SOFA2 or GOPAVRS device into its housing for
plug-in cards AUX.
Connecting terminal 41 enables a safety edge test cycle before
every operation.
If the test fails the SA led flashes and the test is repeated.
1 6 N.C. OPENING SAFETY
DEVICE
Connect the output contact of device SOFA1-SOFA2 to terminals 1-6
on the control panel (in series with the photocell output contact, if
installed).
1 7 N.C. CLOSING SAFETY
DEVICE
Connect the output contact of device SOFA1-SOFA2 to terminals 1-7
on the control panel (in series with the photocell output contact, if
installed).
1 8 N.C. REVERSAL SAFE-
TY DEVICE
Connect the output contact of device SOFA1-SOFA2 to terminals 1-8
on the control panel (in series with the photocell output contact, if
installed).
ATTENTION: for quick operation on the safety edge, connect it to
contact 1-6 or to contact 1-7.

30
IP1854EN - 2015-04-17
Output Value - Accessories Description
15 ... 024 V 1,2 A
Accessories power supply.
Power supply output for external accessories, including automation
status lamp.
NOTE: the maximum absorption of 0.5 A corresponds to the sum of
all terminals 1.
The control panel has two spaces for coupling board, type radio recei-
vers, magnetic loops etc.
The coupling board working mode is selected by DIP1.
WARNING: the plug-in cards must be inserted and removed with the
power supply disconnected.
Automation open lamp.
Only with limit switch 0-11 (NC) connected and in one motor mode
(jumper OM=OFF) will the lamp extinguish when automation is closed.
15 ... 012 V~ 15 W
Automation closed lamp.
Only with limit switch 0-12 (NC) connected and in one motor mode
(jumper OM=OFF) will the lamp extinguish when automation is open.
M1
UVW
230 V~ 2,5 A
120 V (LOGICMJ)
Automation open lamp.
A lamp lights up that extinguishes only when automation is closed.
M2
XYZ
230 V~ 2,5 A
120 V (LOGICMJ)
Flashing light.
Activated during opening and closing operations.
NL W... ... LAMP
230 V~ 100 W
120 V~ (LOGICMJ)
Lampeggiante.
Il lampeggiante si attiva contemporaneamente alla manovra di aper-
tura e chiusura.
NL X... ... 230 V~ 100 W
120 V~ (LOGICMJ)
Luce di cortesia.
Solo in modalità 1 motore (ponticello OM=OFF e in assenza di motore
collegato ai morsetti X-Z-Y) è possibile collegare una luce di cortesia che
si attiva per 180 s al ricevimento di ogni comando di apertura (totale o
parziale) e chiusura.
J7
Pulsantiera a membrana (PT3). Attiva la manovra di apertura.
NOTA: per attivare la manovra di chiusura collegare il connettore della
pulsantiera a J7 ruotato di 180°.
Pulsantiera a membrana (PT3). Provoca l’arresto del movimento.
Pulsantiera a membrana (PT3). Attiva la manovra di chiusura.
NOTA: per attivare la manovra di apertura collegare il connettore della
pulsantiera a J7 ruotato di 180°.

31
IP1854EN - 2015-04-17
6. Adjustments
6.1 Trimmer
6.2 Dip-switch
Trimmer Description
TM
MIN=10 s MAX=120 s
60 s
Setting the operating time.
From 10 to 120 s.
From 10 to 150 s with OM=OFF and JR6=OFF.
NOTE: with NC limit switch, set TM=MAX.
TC
MIN=0 s MAX=120 s
Setting motor 1 (M1) closing delay time.
When closing, motor 1 (M1) starts after a delay set with TR from 0 to 30 s relative to
M2. When opening, motor 2 (M2) starts after a delay of 3 s relative to M1.
If TR=MIN, the door wings start simultaneously.
NOTE: we recommend setting TR=MIN with non-overlapping door wings, and setting
TR>3 s with overlapping door wings.
RP
0 s 30 s
Setting automatic closing time. From 0 to 120 s.
With DIP3=OFF, once a safety switch has been activated, the counter starts as soon
as the safety switch is released (for example, after passing through the photocells),
and lasts for a period of time set with TC (50%).
With DIP3=ON, the counter starts when automation is opened and lasts for the entire
duration set with TC (100%).
NOTE: after the activation of the stop command, once contact 1-9 has closed again,
automatic closing is only enabled after a total, partial or step-by-step opening com-
mand.
TR
MIN=0 s
10 s
20 s
30 s
3 s
Power setting.
Sets voltage supplied to motor (1=MIN / 5=MAX).
R1
MAX=disabled
MIN
Setting obstacle thrust.
The control panel is equipped with a safety system that stops motion if an obstacle is
encountered during an opening operation and either stops or reverses motion during
a closing operation.
R1=MIN gives maximum obstacle sensitivity (minimum thrust).
R1=MAX disables detection (maximum thrust).
RF
CT 12345
Setting motor 1 (M1) partial aperture.
From 0 to 30 s.
DIP Description OFF ON
DIP1 Radio mode. Step-by-Step. Opening.
DIP2 Direction selection with OM=OFF
(one motor mode).
Opens towards right. Opens towards left.
DIP3 Restore automatic closing time. 50% 100%
DIP4 Automation status at power on.
Indicates how the control panel
considers automation when po-
wered up.
Open.
NOTE: with a limit switch installed,
preferably set DIP4=OFF.
Closed.
NOTE: if the automatic
closing function is not used,
preferably set DIP4=ON.
DIP5 Electric lock release. Disabled. Enabled.
DIP6 Preflashing set at 3 s. Disabled during opening.
Enabled only with automatic clo-
sing and with TC setting greater
than 3 s.
Enabled for both opening
and closing.
ATTENTION: disconnect the power supply before adjusting.

32
IP1854EN - 2015-04-17
6.3 Jumper
6.4 Signals
Jumper Description OFF ON
JR4 Overtravel reduction.
Reduces the overtravel distance
for the door wing.
Disabled.
NOTE: set JR4=OFF is the motor
is equipped with an electric brake.
Enabled.
NOTE: preferably set
JR4=ON if the door wing
performs an excessive
overtravel.
JR6 Application type. Sliding gate. Other applications.
NIO Electronic antifreeze system.
Maintains motor function even at
low ambient temperatures.
NOTE: for correct operation, the
control panel must be exposed to
the same ambient temperature
as the motors.
Enabled.
ATTENTION: do not use with LO-
GICMJ.
Disabled.
JR10 Maximum power at start. Disabled.
The motor starts with the voltage
set with RF.
Enabled.
The motor starts at maxi-
mum power for 1 s.
OM Automation type. One motor automation (M1 only). Automation with two inde-
pendent motors.
D5 Step-by-step sequence. Open-stop-close-stop-open. Open-stop-close-open.
S5 Step-by-step sequence stop du-
ration.
Permanent.
(Automatic closing disabled).
Temporary.
(Automatic closing ena-
bled).
JT Closing operation time. Set with TM+4 s.
NOTE: set JT=OFF with hydraulic
or friction gearmotor.
Automatic.
EO Electric lock function. Powered with automation closed. Powered for 1 s at the
beginning of the opening
operation.
SO Reversal safety switch func-tion. With automation stopped and con-
tact 41-8 open, opening operations
are permitted.
With automation stopped
and 41-8 open, all opera-
tions are disabled.
LED On Flashing
POWER 24 V power supply /
SA Indicates that at least one of the safety contacts is
open.
Safety test failure (terminal 41).
Operations count performed (only when
control panel is switched on):
= 1000 operations
= 10000 operations
IN Activated at every command and adjustment to the
dip-switch and jumper. /
11 Indicates that the 0-11 limit switch contact is open. /
12 Indicates that the 0-12 limit switch contact is open. /

33
IP1854EN - 2015-04-17
i
NOTE: in the event of servicing or if the control panel is to be replaced, repeat the start-up procedure.
7. Starting
 Bridge the NC safety contacts with a jumper.
 Before starting up, check the application type selected. In the case of single door wing auto-
mation, set OM=OFF. For sliding gate automation, set JR6=OFF.
 Any limit switches installed must be adjusted so that they are triggered near the mechanical
opening and closing end stops. Set TM=MAX.
NOTE: limit switches must be kept pressed until the operation has been completed.
 If no limit switches are installed, bridge terminals 0-11 and 0-12 with jumpers and set TM
to half.
 Set RF=3 and R1 to half.
 Set TR>3 s in the case of automation with two overlapping door wings.
 Switch on power.
 Swap the motor polarity if the direction of motion of the door wings is incorrect.
NOTE: the first closing operation requested after a power outage is performed, if TR>MIN, with
one door wing at a time (first the door wing powered by motor M2, then the door wing powered
by motor M1), whereas if TR=MIN, the door wings start simultaneously.
 Perform opening and closing commands and check that the automation functions correctly
and that the limit switches (if installed) are correctly set.
 Connect the safety devices (removing the relative jumpers) and check that they function
correctly.
 If required, activate automatic closing and adjust with the TC trimmer.
 Set RF to a position that allows the automation to function correctly while ensuring the safety
of the user in the event of collision.
 Set obstacle thrust with R1.
NOTE: if the door wing closing second encounters an obstacle, both door wings are reopened.
The subsequent closing operation is performed one door wing at a time.
 Ensure that the forces exerted by the door wings are compliant with EN12453-EN12445
regulations.
 If required, set the partial aperture of motor 1 with RP.
 If required, connect the radio receiver to the relative AUX connector, programme the transmit-
ters as described in the relative manual and check that all elements function correctly.
 Connect any other accessories and check operation.
 Once the start up and check procedures are completed, close the container.
ATTENTION: The following operations are performed with no safety devices
WARNING: the plug-in cards must be inserted and removed with the power supply disconnected.

34
IP1854EN - 2015-04-17
8. Troubleshooting
Problem Possible causes Remedy
Automation does not open or close. No power.
(POWER led off).
Check that the control panel is po-
wered correctly.
Short circuited accessories.
(POWER led off).
Disconnect all accessories from
terminals 0-1 (voltage must be 24
V=) and reconnect one at a time.
Blown line fuse.
(POWER led off).
Replace fuse.
Safety contacts are open.
(SA led on).
Check that the safety contacts are
closed correctly (N.C.).
Safety contacts not correctly con-
nected or self-controlled safety
edge SOFA1-SOFA2 not functioning
correctly.
(SA led flashing).
Check connections to terminals 6-7-
8 on control panel and connections
to the self-controlled safety edge
SOFA1-SOFA2.
Release microswitch open (if in-
stalled).
Check that the hatch is closed cor-
rectly and the microswitch makes
contact.
The motor thermal overload switch
is open.
Check for continuity between the
phases of the motors disconnected
from the control panel.
Automation opens but does not
close.
Safety contacts are open.
(SA led on).
Check that the safety contacts are
closed correctly (N.C.).
Safety contacts not correctly con-
nected or self-controlled safety
edge SOFA1-SOFA2 not functioning
correctly.
(SA led flashing).
Check connections to terminals 6-7-
8 on control panel and connections
to the self-controlled safety edge
SOFA1-SOFA2.
Photocells activated.
(SA led on).
Check that the photocells are clean
and operating correctly.
The automatic closing does not
work.
Check that contact 1-2 is closed.
External safety devices not activa-
ting.
Incorrect connections between the
photocells and the control panel.
Connect NC safety devices together
in series and remove any bridges on
the control panel terminal board.

35
IP1854EN - 2015-04-17
9. Example application for two-motors swing
gates
When the LOGICM control panel is used in automation applications with two
swinging door wings, one of the following operating modes may be selected.
Example 1 - Door wings stop against mecha-
nical end stops and in the event of obstacle de-
tection.
Set an operating time of 2-3 s longer than the
effective time taken by the door wing (TM<MAX)
and bridge terminals 0-11-12 with jumpers. In
this configuration, each door wing will come to
a stop against mechanical opening and closing
end stops and in the event of obstacle detection.
Example 2 - Door wings stop against limit
switches and in the event of obstacle detection.
The NC contacts of the opening and closing limit
switches are connected in series with the motor
phases.
Set an operating time TM<MAX and bridge ter-
minals 0-11-12 with jumpers.
In this configuration, each door wing will come
to a stop against the opening and closing limit
switches and in the event of obstacle detection.
Example 3 - Door wings stop against limit
switches and reverse motion in the event of ob-
stacle detection.
Set an operating time TM=MAX and connect the
closing limit switch NC contacts to terminals
0-11-12 and the opening limit switch NC con-
tacts in series with the open phase of each motor.
With this configuration, each of the door wings
stops when the limit switches are activated.
In the event of obstacle detection while opening,
only the door wing that detects the obstacle
stops, performing a disengagement operation,
whereas during a closing operation, both door
wings reopen.
Example 4 - Door wings stop against mechani-
cal end stops and reverse motion in the event of
obstacle detection.
Set an operating time 2-3 s greater than the ef-
fective time taken by the door wing (TM<MAX)
and connect the closing proximity limit switch
NO contacts to terminals 0-11-12, positioning
TM
<MAX <MAX
TC RP TR R1
15141312110011234567892041UWV X Z Y
com com
M1
1~
M2
1~ Limit switch (230 V 5A)
TM
<MAX <MAX
TC RP TR R1
15141312110011234567892041
TM TC RP TR R1
15141312110011234567892041UWV X Z Y
com com
M1
1~
M2
1~
Opening limit switch (230 V 5A)
Closing
limit switch
=MAX <MAX
TM TC RP TR R1
15141312110011234567892041
Closing
proximity switch
<MAX <MAX

36
IP1854EN - 2015-04-17
the switches 2-3 s ahead of the mechanical
end stop. In this configuration, each door wings
stops against its respective mechanical closing
and opening end stop. In the event of obstacle
detection while opening, only the door wing that
detects the obstacle stops, performing a disen-
gagement operation. In the event of obstacle
detection during closing and before the activa-
tion of the proximity limit switch, the door wings
reopen; after the activation of the proximity limit
switch, the door wings stop against the obstacle.
Example 5 - The door wings stop against the li-
mit switches when opening and against the me-
chanical end stops when closing, and reverse
motion when an obstacle is detected.
Set an operating time 2-3 s greater than the ef-
fective time taken by the door wing (TM<MAX)
and connect the closing proximity limit switches
to terminals 0-11-12, positioning the switches
2-3 s ahead of the mechanical end stop. Connect
the opening NC limit switches in series to the
open phase of each motor. In this configuration,
the door wing stops against the mechanical end
stop when closing, and when the relative limit
switch is activated when opening. When an ob-
stacle is detected during opening, the door wing
stops, performing a disengagement operation.
In the event of obstacle detection during closing
and before the activation of the proximity limit
switch, the door wings reopen; after the activa-
tion of the proximity limit switch, the door wings
stop against the obstacle.
TM TC RP TR R1
15141312110011234567892041UWV X Z Y
com com
M1
1~
M2
1~
Opening limit switch (230 V~ 5A)
Closing
proximity switch
<MAX <MAX

37
IP1854EN - 2015-04-17
10. Example application for one-motor swing
gate
When the LOGICM control panel is used in automation applications with one
swinging door wing, one of the following operating modes may be selected.
Example 1 - Door wing stops against mechanical
end stops and in the event of obstacle detection.
Set an operating time of 2-3 s longer than the ef-
fective time taken by the door wing (TM<MAX) and
bridge terminals 0-11-12 with jumpers. In this con-
figuration, the door wing will come to a stop against
mechanical opening and closing end stops and in
the event of obstacle detection.
Example 2 - Door wing stops against limit switches
and in the event of obstacle detection.
The NC contacts of the opening and closing limit
switches are connected in series with the motor
phases.
Set an operation time TM<MAX and bridge termi-
nals 0-11-12 with jumpers. In this configuration,
the door wing stops against the opening and clo-
sing limit switches and in the event of obstacle de-
tection.
Example 3 - Door wing stops against limit switches
and reverses motion in the event of obstacle de-
tection.
Set an operating time TM=MAX and connect the
opening and closing limit switch NC contacts to
terminals 0-11-12.
In this configuration, the door wing stops when the
limit switches are activated.
In the event of obstacle detection while opening,
the door wing stops, performing a disengagement
operation, whereas during a closing operation, the
door wing reopens.
Example 4 - Door wing stops against mechanical
end stops and reverses motion in the event of ob-
stacle detection.
Set an operating time of 2-3 s longer than the ef-
fective time taken by the door wing (TM<MAX) and
position the proximity limit switches 2-3 s ahead of
the mechanical end stop.
In this configuration, the door wing stops against
its respective mechanical closing and opening end
TM TC RP TR R1
OM=OFF
15141312110011234567892041
<MAX <MAX
TM TC RP TR R1
15141312110011234567892041UWV X Z Y
com
M1
1~ Limit switch (230 V 5A)
OM=OFF
<MAX <MAX
TM TC RP TR R1
15141312110011234567892041
Closing limit switch
Opening limit switch
OM=OFF
=MAX <MAX
TM TC RP TR R1
15141312110011234567892041
Closing proximity switch
Opening proximity switch
OM=OFF
<MAX <MAX

38
IP1854EN - 2015-04-17
TM TC RP TR R1
15141312110011234567892041UWV X Z Y
com
M1
1~
Opening limit switch (230 V 5A)
Closing
proximity switch
OM=OFF
<MAX <MAX
stop.
In the event of obstacle detection before the ac-
tivation of the proximity limit switch while ope-
ning, the door wing stops, performing a disen-
gagement operation; after the proximity limit
switch is activated, the door wing stops against
the obstacle.
In the event of obstacle detection during closing
and before the activation of the proximity limit
switch, the door wing reopens; after the proximi-
ty limit switch is activated, the door wing stops
against the obstacle.
Example 5 - The door wing stops against the
limit switch when opening and against the me-
chanical end stop when closing, and reverses
motion in the event of obstacle detection.
Set an operating time of 2-3 s longer than the
effective time taken by the door wing (TM<MAX),
position the proximity limit switches 2-3 s ahe-
ad of the mechanical end stop and connect the
opening limit switch NC in series to the opening
phase of the motor.
In this configuration, the door wing stops against
the mechanical end stop when closing, and
when the relative limit switch is activated when
opening. When an obstacle is detected during
opening, the door wing stops, performing a di-
sengagement operation. In the event of obstacle
detection during closing and before the activa-
tion of the proximity limit switch, the door wing
reopens; after the proximity limit switch is acti-
vated, the door wing stops against the obstacle.

39
IP1854EN - 2015-04-17
11. Example application for sliding gate
12.Example application for barriers
When using the LOGICM control panel for sliding au-
tomation applications:
- set OM=OFF
- set JR6=OFF
- set TM=MAX (150 s).
Connect the opening and closing limit switch NC con-
tacts to terminals 0-11-12.
With this configuration, the door wing stops when the
limit switches are activated.
In the event of obstacle detection while opening, the
door wing stops, performing a disengagement ope-
ration, whereas during a closing operation, the door
wing reopens.
Select the correct opening direction with DIP2.
 In the event of automation with right-side opening
seen from the automation side (DIP2=OFF), connect
the opening limit switch to terminals 0-12 and
closing limit switch to terminals 0-11.
 In the event of automation with left-side opening
seen from the automation side (DIP2=ON), connect
the opening limit switch to terminals 0-11 and the
closing limit switch to terminals 0-12.
When using the LOGICM control panel for barrier
applications:
- set OM=OFF
- set RF=5 (MAX)
- set TM=MAX
Select the correct opening direction with DIP2.
 In the event of automation with right-side opening
seen from the automation side (DIP2=OFF), connect
the opening limit switch to terminals 0-12 and
closing limit switch to terminals 0-11.
 In the event of automation with left-side opening
seen from the automation side (DIP2=ON), connect
the opening limit switch to terminals 0-11 and the
closing limit switch to terminals 0-12.
TM TC RP TR R1
15141312110011234567892041
Limit switch Limit switch
OM=OFF
JR6=OFF
1
ON
23456
DIP2=OFF
DIP2=ON
1
ON
23456
1
ON
23456
=MAX <MAX
TM
RF
TC RP TR R1
15141312110011234567892041
Limit switch Limit switch
OM=OFF
1
ON
23456
DIP2=OFF
DIP2=ON
1
ON
23456
1
ON
23456
=MAX <MAX
CT12345

40
IP1854EN - 2015-04-17
13. Example of automation in parallel
A B
The two automations [A] and [B] can be operated in parallel by making the connections indicated
in the figure.
Commands 1-3 and the remote controls (with DIP1=ON) are equivalent to a total opening command.
Automatic closing is obtained by adjusting the TC trimmer not at the maximum and in the same
position on both control panels.
TM TC RP TR R1
TM TC RP TR R1
15141312110011234567892041
06841 68
OM=OFF
JR6=OFF
1
ON
23456
LOGICM
SWT
ALOGICM B
15141312110011234567892041
OM=OFF
JR6=OFF
1
ON
23456
OUT2
06841 68SWT
BIXLR22 JR1 JR2
Opening
Closing
Safety while opening
Stop
Partial opening
i
N.B.: the opening and closing movements are not synchronised, including reopening after
activation of the photocells.
WARNING: in the absence of safety edge SOFA1-SOFA2, connect commands 1-8 to the
SWT card.
Commands 41-6 and 41-7 can only be connected on the respective control panel.

41
IP1854EN - 2015-04-17
All the rights concerning this material are the exclusive property of Entrematic Group AB. Although the con-
tents of this publication have been drawn up with the greatest care, Entrematic Group AB cannot be held
responsible in any way for any damage caused by mistakes or omissions in this publication.
We reserve the right to make changes without prior notice. Copying, scanning and changing in any way are
expressly forbidden unless authorised in writing by Entrematic Group AB.

IP1854EN - 2015-04-17
Entrematic Group AB
Lodjursgatan 10
SE-261 44, Landskrona
Sweden
www.ditecentrematic.com