enware LEVA Series User manual

Call 1300 369 273
www.enware.com.au
Enware Australia Pty Limited
9 Endeavour Rd Caringbah NSW 2229 Australia
Ph: 02 8536 4000 [e-mail]
LEV80308SQ
I00226_Oct 19
LEVA 80mm SEQUENTIAL SHOWER MIXER
Installation and Maintenance Instructions

2 Call 1300 369 273 www.enware.com.au
Working Pressure Range 50-800 kPa
Recommended Maximum Pressure 500 kPa*
Working Temperature Range 5 °C – 85 °C *
compliance
*Enware products are to be installed in
accordance with the Plumbing Code of
Australia and AS/NZS3500.
Reference should also be made to the
Australasian Health Facility Guidelines (AHFG),
ABCB and Local Government regulaons when
considering the choice of, and the installaon
of these products.
Thermostac Mixing Valves and Pressure
Reducon Valves may be required to comply
with maximum temperature and pressure
requirements.
please note
Enware Australia advises:
1. Due to ongoing Research and Development,
specicaons may change without noce;
2. Component specicaons may change on
some export models.
before installation
Before proceeding with installaon
• Ensure all operang & dimensional
specicaons are suitable for the intended
installaon.
• Ensure all supply lines are ushed
thoroughly to remove debris prior to
the installaon of this product as per
AS/NZS 3500.1. Strainers (40 mesh) are
recommended if debris is an ongoing
problem.
SEQUENTIAL LEVER MIXER
Installation & Maintenance Instructions
technical data
For use with potable water only.

www.enware.com.au Call 1300 369 273 3
dimensions
85
107 max.
26
51
51
G1/2" (BSP
)
FEMALE OUTLET
54
G1/2" (BSP)
FEMALE INLET
G1/2" (BSP
)
FEMALE INLET
75
FULL WARM
FULL COLD
CLOSED
IN-WALL
ADJUSTMENT
components
SHOWER MIXER BODY
FLANGE
SEQUENTIAL CARTRIDGE
180° RTC
COLOUR INDICATORS
LOCKNUT
SPLINE ADAPTOR
TOOTH WASHER
NYLON WASHER
M5x20 HANDLE S/S SCREW
LEVA SEQUENTIAL
80MM HANDLE

4 Call 1300 369 273 www.enware.com.au
ROUGH IN
Determine Location of Shower Mixer
Wall depth: min 50mm – max 75mm from finished wall
surface to the back of body.
The mixer must be installed in the correct orientation
with the 2 inlets in the horizontal plane (hot / warm on
left) and outlet facing the top.
Where required, an appropriate backflow prevention
device should be installed before a shower hose,
according to the cross-connection hazard rating.
(E.g. in cases where a shower hose is installed over a
bath, the shower outlet is installed at a low height, or
a shower hose is long enough to reach the floor, bidet
or a WC pan.) Refer to AS3500.1 - Section 4.
installation instructions
50 min.
75 max.
COLD IN
HOT or WARM IN
COLD / MIXED /
WARM or HOT OUT
Grey (O)
Blue (Cold)
Red / Yellow
(Hot / Warm)
In-Wall Body Component
1. Ensure plumbing lines are flushed prior to
installation as debris in cartridge will void warranty.
2. Secure the Shower Mixer Body to the internal
cavity within the wall. The Shower Mixer Body
can be fixed to a masonry wall or wall frame using
screws suitable for the fixing method. (Fixing
screws not supplied.)
When mounting Shower Mixer Body on the wall,
take note of the minimum and maximum wall
thickness and the dimensions shown so that the
nogging or recess is correctly positioned and takes
into account the thickness of the finished wall.
3. Purge hot and cold water lines, and connect
water supply pipework to the hot and cold inlets.
Connect the shower outlet to the riser leading to
shower rose / outlet.
50 min.
75 max.

www.enware.com.au Call 1300 369 273 5
NOTE: The mixer body has ‘H’ and ‘C’ markings
to indicate the appropriate supply required to each
side of the mixer.
WARNING: Heat must NOT be applied to
the inlets and outlet of the mixer as this will
result in damage to the cartridge and void the
warranty.
4. Loosely place spline adaptor and handle on spline
of mixer cartridge.
5. Turn on Hot and Cold water supplies and test for
leaks within the pipework connection.
6. Test operation of the tap. Turn mixer handle and
test functionality of the system. If there is any
problem see Troubleshooting Section following or
contact Enware.
7. Take handle off the mixer, and keep handle and
flange components in a secure place until fit off.
FIT OFF - FLANGE AND HANDLE
1. After waterproofing and bathroom finishing trades
are complete, operate the mixer to ensure system
is still functional.
2. Seal any gaps between the wall cut-out and the
Shower Mixer Body, with appropriate silicone
sealant.
3. Insert colour indicators into Flange, with Red or
Yellow on top, Blue on the right, and Grey at the
bottom.
4. Apply a bead of silicone sealant on the back of
Flange so it can seal against the wall. Fit Flange
over the mixer and push firmly against the wall.
5. Place spline adaptor and handle onto the cartridge
spline so that the handle is facing down.
6. Operate the mixer, ensure the handle points in the
correct orientation and that it aligns with the red/
yellow, blue and grey markings on the flange.
CLOSED
COLD - LOW FLOW
COLD - FULL FLOW
MIXED COLD AND
WARM / HOT - FULL FLOW
FULL WARM or HOT
- FULL FLOW
CLICK
CLICK
CLICK

6 Call 1300 369 273 www.enware.com.au
7. Fix the Spline Adaptor in place using the Tooth
Washer, Nylon Washer and S/S Screw.
8. Fit handle on and secure in place by tightening the
grub screw with a 2.5mm Allen Key. Put on cap for
the grub screw.
SPLINE ADAPTOR
TOOTH WASHER
NYLON WASHER
M5x20 S/S SCREW
LEVA SEQUENTIAL
80MM HANDLE
The sequential lever turns progressively from “OFF” to
“COLD” to “WARM” or “HOT”.
Starting from OFF position (handle lever pointing
straight down),
To operate the tap, turn the lever anticlockwise. The
flow volume gradually increases. At COLD position,
cold water is at its full flow.
Turning the lever further past COLD, the flow rate
stays at maximum but now the water is mixed with
more hot or warm water.
At “WARM” or “HOT” position (handle pointing straight
up), it is at full temperature and flow supplied to the
hot inlet of the mixer, and is no longer mixed with cold
water.
operating instructions
Enware Product should be cleaned with a soft damp cloth using only mild liquid detergent or
soap and water. Do not use cleaning agents containing a corrosive acid, scouring agent or
solvent chemicals. Do not use cream cleaners, as they are abrasive. Epoxy coated surfaces
should only be cleaned with a cloth and clear water or mild detergent. Use of unsuitable
cleaning agents may damage the surface. Any damage caused in this way will not be
covered by warranty.
cleaning
CLOSED
COLD - LOW FLOW
COLD - FULL FLOW
MIXED COLD AND
WARM / HOT - FULL FLOW
FULL WARM or HOT
- FULL FLOW
CLICK
CLICK
CLICK

www.enware.com.au Call 1300 369 273 7
PROBLEM CAUSE RECTIFICATION
Tap is dripping water Debris is caught
inside cartridge /
Cartridge is worn or
damaged /
Pressure too high
Remove and flush Cartridge,
inspect and remove any debris.
Replace Cartridge if damaged.
Install pressure reduction valve,
ensure it is under 500 kPa
Water is leaking from spindle Seal in Cartridge is
worn or damaged /
Pressure too high
Replace Cartridge
Install pressure reduction valve,
ensure it is under 500 kPa
Water is not flowing from tap Water turned off Turn water on
troubleshooting
spare parts
PART ENWARE PRODUCT CODE
Handle Assembly 80mm
Complete
LEV80378SQ
Sequenal Cartridge Kit
180° RTC
LEVSQSBA-180
Spline Adaptor LEVSQHEX
Grub Screw M5 Dog Point
(Pack of 6) GSCREWDPM5
Shower Wall Flange (Dress Ring) LEVSQSHFLAN
Colour Indicator Pack (1x Yellow,
1x Grey, 1x Blue, 1x Red) LEVSQIND
Shower Mixer Body LEVSQSHMIX

8 Call 1300 369 273 www.enware.com.au
product warranty for Australia Eecve 1 September 2014
Enware Australia Pty Limited (ACN 003 988 314)
(“we” or “us”) warrants that this product (also referred
to as “our goods”) will be free from all defects in
materials and workmanship for 12 months* from the
date of purchase. Our liability under this warranty is
limited at our opon to the repair or replacement of
the defecve product or part, the cost of repair of the
defecve product or part or the supply of an equivalent
product or part, in each case if we are sased the
loss or damage was due to a defect in the materials or
workmanship of the product or part. All products must
be installed in accordance with the manufacturer’s
instrucons, the PCA, and AS/NZS3500 including any
other applicable regulatory requirements.
exceptions
This warranty does not apply in respect of any damage or
loss due to or arising from:
a) Failure by you or any other person to follow any
instrucons for use (including instrucons and direcons
relang to the handling, storage, installaon, ng,
connecon, adjustment or repair of the product)
published or provided by us;
b) Failure by you or any other person responsible for the
ng, installaon or other work on the product to follow
or conform to applicable laws, standards and codes
(including the AS/NZ 3500 set of Standards, all applicable
State and Territory Plumbing Codes, the Plumbing Code
of Australia and direcons and requirements of local and
other statutory authories); or
c) Any act or circumstance beyond our control including
faulty installaon or connecon, accident, abnormal use,
acts of God, damage to buildings, other structures or
infrastructure and loss or damage during product transit
or transportaon.
making a claim
To make a claim under this warranty you must nofy us
in wring or via the Online Product Service and Warranty
Form** within 7 days of any alleged defect in the
product coming to your aenon. Proof of purchase of
the product must also be supplied. All nocaons and
accompanying informaon must be sent marked for the
aenon of the Enware Australia Pty Limited,
9 Endeavour Road, Caringbah NSW 2229.
Phone or email contact is possible also, phone
1300 369 273 (AUS) or [phone] or
email inf[email protected]om.au
Your costs in making a claim under this warranty,
including all freight, collecon and delivery costs, are
to be borne and paid by you. We also reserve the right
at our cost to inspect any alleged defect in the product
wherever it is located or installed or on our premises.
** www.enware.com.au/product-service-enquiry
* 1 Year parts and labour on the complete assembly.
Aer 1 year, a further 4 years parts only warranty is
applicable to sequenal valve cartridge.
other conditions
Except as provided or referred to in this document,
we accept no other or further liability for any damages
or loss (including indirect, consequenal or economic
loss) and whether arising in contract, tort or otherwise.
Any benets available to you under this warranty are
in addion to any non-excludable rights or remedies
you may have under applicable legislaon, including
as a “consumer” under the Australian Consumer Law.
To that extent you need to be aware that: Our goods
come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entled to a
replacement or refund for a major failure and for
compensaon for any other reasonably foreseeable
loss or damage. You are also entled to have the
goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount
to a major failure.