enware Wellbeing Livia LIV80WSET User manual

I00429_Oct 21
Installation and Maintenance Instructions
Wellbeing®Livia Wall Set
Call 1300 369 273
www.enware.com.au
Enware Australia Pty Limited
9 Endeavour Rd Caringbah NSW 2229 Australia
Ph: 02 8536 4000 [e-mail]
LIV80WSET
LIV80LTC-B
LIV80LTC-RY
LIV80RTC-B
LIV80RTC-RY
technical data
Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA) and AS/NZS3500.
Installations not complying with PCA and AS/NZS 3500 may void the product and performance warranty provisions.
Reference should also be made to the Australasian Health Facility Guidelines (AHFG), ABCB and Local Government
regulations when considering the choice of, and the installation of these products.
This product must be installed and commissioned by a qualified plumber.
For use with potable water only.
NOTE: Enware Australia advises:
1. Due to ongoing Research and Development, specifications may change without notice.
2. Component specifications may change on some export models.
*Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA) and
AS/NZS3500. Installations not complying with PCA and AS/NZS 3500 may void the product and
performance warranty provisions.
Reference should also be made to the Australasian Health facility Guidelines (AHFG), ABCB and
Local Government regulations when considering the choice of, and the installation of these products.
NOTE: Enware Australia advises:
1. Due to ongoing Research and Development, specifications may change without notice.
2. Component specifications may change on some export models.
**10 year parts warranty on ceramic disc. 2 years parts and labour warranty on the full assembly with
additional 8 years parts only warranty.
Working Pressure Range 100 - 800 kPa*
Maximum Temperature 85°C
Technical Information

2 Call 1300 369 273 www.enware.com.au
1 Lever handle yellow
2 Lever handle red
3 Lever handle blue
4 Circlip
5 Handle insert
6 Flange Dome
7 O-ring BS032
8 Locknut
9 Fibre washer
10 SBA Spindle hot
11 SBA Spindle cold
12 VP spanner
10
2
1
12
3
4
5
6
7
8
9
11

www.enware.com.au Call 1300 369 27 3
• All supply lines must be flushed thoroughly to remove debris
prior to the installation of this product, as per AS/NZS
3500.1. Strainers (40 mesh) are recommended if debris is
an ongoing problem.
• A pressure reduction valve may be required to comply
with the recommended maximum supply pressure and/or
balanced pressure requirements.
INSTALLATION
1. Prepare shower breech in wall, taking into account the
wall depth required for the tap.
Minimum 6mm, maximum 15mm from finished wall to the
face of tap body. SEE IMAGE 01
2. After the wall is finished, screw SBA spindle into tap body
in wall. Use the hex provided on the SBA to tighten with a
spanner. Do not over-tighten.
(Max. torque 18Nm) SEE IMAGE 02
Take note of the way the handles turn.
LTC (Anti-clockwise to close) is marked with blue.
RTC (Clockwise to close) is marked with red on the
spindle. SEE IMAGE 06
3. Fit fibre washer [9] onto spindle and screw locknut [8]
onto SBA spindle [10, 11]. Tighten locknut with a spanner.
(Max. torque 30Nm) SEE IMAGE 03
4. Fit flange dome [6] onto spindle. Ensure the O-ring [7] is in
place. SEE IMAGE 04
OPEN
CLOSED
80
67 15 MAX.
6 MIN.
61
G5/8" (BSP)
IMAGE 01
MAX 18Nm
IMAGE 02
installation
IMAGE 04
MAX 30Nm
IMAGE 03

4 Call 1300 369 273 www.enware.com.au
5. Fit handle insert [5], then circlip [4] onto spindle.
SEE IMAGE 05
6. Fit lever handle onto spindle. Note the position of the handle
at closed position. SEE IMAGE 06
7. Fix the lever handle in place using spanner [12].
SEE IMAGE 09
8. Turn on water supply and test operation.
IMAGE 05
IMAGE 09
IMAGE 06
Red / Hot Blue / Cold
OPEN
CLOSED
80
67
15 MAX.
6 MIN.
61
G5/8" (BSP)
LT C Anti-Clockwise to Close
OPEN
CLOSED
80
67
15 MAX.
6 MIN.
61
G5/8" (BSP)
RTC Clockwise to Close

www.enware.com.au Call 1300 369 27 5
maintenance
CLEANING
Enware products should be cleaned with a soft damp cloth using only mild liquid detergent or
soap and water. Do not use cleaning agents containing a corrosive acid, scouring agent or solvent
chemicals. Do not use cream cleaners, as they are abrasive. Use of unsuitable cleaning agents may
damage the surface. Any damage caused in this way will not be covered by warranty.
troubleshooting
PROBLEM CAUSE RECTIFICATION
Water leaking from outlet
Water dripping and does
not shut off
SBA has debris caught in the
mechanism.
Remove SBA and inspect.
Remove debris and/or replace
SBA if damaged.
Install an inline strainer.
Tap seat is damaged Refurbish tap seat using a
reseating tool. If necessary, fit
reseating kit or replace tap body.
Water is leaking from
spindle
O-ring on SBA is worn or
damaged
Replace SBA.
Water is not flowing from
tap
Poor water flow from outlet
Water turned off. Turn water on.
Flow control is blocked by
debris.
Remove flow control from
shower head and clean debris.
Install an inline strainer.
Handle is wobbly
Handle feels loose
Circlip missing
Handle insert not tightened
Ensure circlip is in place
Tighten insert using key
Handle does not align
perfectly straight
Adjust position of SBA by taking off SBA locknut, and tightening
or loosening spindle. (Do not adjust position of SBA using handle.
Do not over-tighten spindle.)
Wall flange does not screw
into thread of SBA
Tap bodies are set too far into
the wall
Use extended recess spindle
(SBA) or tap body extender.
Wall flange does not screw
down onto wall surface
Tap bodies are set too far out Use a trouble dome or flange
extender

6 Call 1300 369 273 www.enware.com.au
spare parts
DESCRIPTION PART CODE
Lever handle - yellow Parts: [1] [4] [5] LIV80HAND-Y
Lever handle - red Parts: [2] [4] [5] LIV80HAND-R
Lever handle - blue Parts: [3] [4] [5] LIV80HAND-R
SBA hot - RTC (Clockwise to close) Parts: [8] [9] [10] LIV80CDSBA2-RTC
SBA cold - LTC (Anti-clockwise to close) Parts: [8] [9] [11] LIV80CDSBA2-LTC
Flange dome Parts: [6] [7] LIV80FLAN
Seals and grub screw kit Parts: 2x of each - [4] [5] [7] LIV80SEALS
10
2
1
12
3
4
5
6
7
8
9
11

www.enware.com.au Call 1300 369 27 7
dimensions
All measurements are in millimetres.
OPEN
CLOSED
80
67
15 MAX.
6 MIN.
61
G5/8" (BSP
)
OPEN
CLOSED
80
67
15 MAX.
6 MIN.
61
G5/8" (BSP)
LT C Anti-Clockwise to Close
OPEN
CLOSED
80
67
15 MAX.
6 MIN.
61
G5/8" (BSP)
RTC Clockwise to Close

8 Call 1300 369 273 www.enware.com.au
product warranty for Australia Eecve August 2021
Enware Australia Pty Limited (ACN 003 988 314)
(“we” or “us”) warrants that this product (also referred
to as “our goods”) will be free from all defects in
materials and workmanship for 10 years* from the date
of purchase. Our liability under this warranty is limited at
our opon to the repair or replacement of the defecve
product or part, the cost of repair of the defecve
product or part or the supply of an equivalent product or
part, in each case if we are sased the loss or damage
was due to a defect in the materials or workmanship
of the product or part. All products must be installed in
accordance with the manufacturer’s instrucons, the
PCA, and AS/NZS3500 including any other applicable
regulatory requirements.
exceptions
This warranty does not apply in respect of any damage or
loss due to or arising from:
a) Failure by you or any other person to follow any
instrucons for use (including instrucons and direcons
relang to the handling, storage, installaon, ng,
connecon, adjustment or repair of the product)
published or provided by us;
b) Failure by you or any other person responsible for the
ng, installaon or other work on the product to follow
or conform to applicable laws, standards and codes
(including the AS/NZ 3500 set of Standards, all applicable
State and Territory Plumbing Codes, the Plumbing Code
of Australia and direcons and requirements of local and
other statutory authories); or
c) Any act or circumstance beyond our control including
faulty installaon or connecon, accident, abnormal use,
acts of God, damage to buildings, other structures or
infrastructure and loss or damage during product transit
or transportaon.
making a claim
To make a claim under this warranty you must
nofy us in wring within 7 days of any alleged defect
in the product coming to your aenon and provide
us with proof of your purchase of the product and
completed the Online Product Service and Warranty
Form available on website www.enware.com.au/
warranty-service-form.
All nocaons and accompanying forms must be sent to
us marked for the aenon of the Enware Australia Pty
Limited, 9 Endeavour Road, Caringbah NSW 2229. We
can also be contacted by telephone [phone]) or by
email ([e-mail]).
Your costs in making a claim under this warranty,
including all freight, collecon and delivery costs, are
to be borne and paid by you. We also reserve the right
at our cost to inspect any alleged defect in the product
wherever it is located or installed or on our premises.
*Condional warranty: 2 Year parts and labour on the
complete assembly with addional 8 years parts only
warranty.
other conditions
Except as provided or referred to in this document, we
accept no other or further liability for any damages
or loss (including indirect, consequenal or economic
loss) and whether arising in contract, tort or otherwise.
Any benets available to you under this warranty are in
addion to any non-excludable rights or remedies you
may have under applicable legislaon, including as a
“consumer” under the Australian Consumer Law. To that
extent you need to be aware that: Our goods come with
guarantees that cannot be excluded under the Australian
Consumer Law. You are entled to a replacement or
refund for a major failure and for compensaon for any
other reasonably foreseeable loss or damage. You are
also entled to have the goods repaired or replaced if
the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
ADDRESS: 9 Endeavour Rd Caringbah NSW 2229 Australia
POSTAL ADDRESS: P.O. Box 2545, Taren Point NSW 2229 Australia
1300 369 273 (AUS) WWW.ENWARE.COM.AU [e-mail]
ABN 23 003 988 314