enware LEVA User manual

I00227_Jul 2016
Call 1300 369 273
www.enware.com.au
Enware Australia Pty Limited
9 Endeavour Rd Caringbah NSW 2229 Australia
Ph: [phone] Fax: [phone]

2
DIMENSIONS
(NOT TO SCALE)
TOP VIEW
SIDE VIEW

3
COMPONENTS
TECHNICAL TABLE
Working Pressure Range
50-800 kPa
Recommended Maximum Pressure
500 kPa *
Working Temperature Range
5 °C –85 °C *
For use with potable water only.

4
COMPLIANCE
* Enware products are to be installed in accordance with the Plumbing Code of Australia and
AS/NZS3500.
Reference should also be made to the Australasian Health facility Guidelines (AHFG), ABCB and
Local Government regulations when considering the choice of, and the installation of these
products.
NOTE: Enware Australia advises:
1. Due to ongoing Research and Development, specifications may change without notice.
2. Component specifications may change on some export models.
This product must be installed and commissioned by a qualified plumber.
INSTALLATION
Rough In
Determine Location of Basin Mixer
Wall depth: min 50mm –max 75mm from finished wall surface to the back of body.
The mixer must be installed in the correct orientation with the 2 inlets in the vertical plane (hot on
the bottom) and outlet on the left.

5
In-Wall Body Component
1. Ensure plumbing lines are flushed prior to installation as debris in cartridge will void
warranty.
2. Secure the Basin Mixer Body to the internal cavity within the wall. The mixer body can be
fixed to a masonry wall or wall frame using screws suitable for the fixing method. (Fixing
screws not supplied.)
When mounting Basin Mixer Body on the wall, take note of the minimum and maximum
wall thickness and the dimensions shown so that the noggin or recess is correctly positioned
and takes into account the thickness of the finished wall.
3. Purge hot and cold water lines, and connect water supply pipework to the hot and cold
inlets.
NOTE: The mixer body has ‘H’ and ‘C’ markings to indicate the appropriate supply required
to each side of the mixer.
WARNING: Heat must NOT be applied to the inlets and outlet of the mixer as this will
result in damage to the cartridge and void the warranty.
4. Loosely place handle on spline of mixer cartridge.
5. Turn on Hot and Cold water supplies and test for leaks within the pipework connection.
6. Test operation of the tap. Turn mixer handle and test functionality of the system. If there is
any problem see Troubleshooting Section following or contact Enware.
7. Take handle off the mixer, and keep handle and flange components in a secure place until fit
off.

6
Fit Off –Facia and Handle
8. After waterproofing and bathroom finishing trades are complete, operate the mixer to
ensure system is still functional.
9. Seal any gaps between the wall cut-out and the mixer body, with appropriate silicone
sealant.
10. Insert colour indicators into Dress Plate, with Red or Yellow on top, Blue on the right, and
Grey at the bottom.
11. Apply a bead of silicone sealant on the back of Dress Plate so it can seal against the wall. Fit
Dress Plate over the mixer and push firmly against the wall.
12. Install spout onto outlet thread. If the 1/2" BSP thread is too long, cut off the excess to suit.
13. Place handle onto the cartridge spline so that the handle is facing down.
14. Operate the mixer, ensure the handle points in the correct orientation and that it aligns with
the red/yellow, blue and grey markings on the flange.

7
15. To secure the handle in place, firstly place the Anti-Rock Spacer Bush onto the cartridge.
16. Secondly, screw in Spindle Adaptor onto spline of cartridge so that it sits approximately
3mm from the cartridge spline.

8
17. Put handle on cartridge spline. Insert grub screw pin through the handle and through the
Spindle Adaptor.
If the grub screw pin doesn’t fit easily at first, remove Leva handle and check alignment of
spindle adaptor. If needed, unscrew or screw in the spindle adaptor 1/4 –1/2 a turn, and
repeat until grub screw pin presses into place correctly.
Handle Too Loose:
If the Leva handle is too loose - remove handle and tighten spindle adaptor 1/4 or 1/2 a
turn, and refit Leva handle.
Handle Too Tight:
If the Leva handle feels too tight for smooth operation –remove handle, loosen spindle
adaptor 1/4- 1/2 a turn and refit Leva handle and repeat until handle operates satisfactorily.
Check LEVA handle for operation. It should turn freely without feeling loose.

9
OPERATING INSTRUCTIONS
The sequential lever turns progressively from “OFF” to “COLD” to “WARM”or “HOT”.
Starting from OFF position (handle lever pointing straight down),
To operate the tap, turn the lever anticlockwise. The flow volume gradually increases. At COLD
position, cold water is at its full flow.
Turning the lever further past COLD, the flow rate stays at maximum but now the water is mixed
with more hot or warm water.
At “WARM” or “HOT” position (handle pointing straight up), it is at full temperature and flow
supplied to the hot inlet of the mixer, and is no longer mixed with cold water.

10
CLEANING
Enware Product should be cleaned with a soft damp cloth using only mild liquid detergent or soap
and water. Do not use cleaning agents containing a corrosive acid, scouring agent or solvent
chemicals. Do not use cream cleaners, as they are abrasive. Epoxy coated surfaces should only be
cleaned with a cloth and clear water or mild detergent. Use of unsuitable cleaning agents may
damage the surface. Any damage caused in this way will not be covered by warranty.
SPARE PARTS
Component
Enware Product Code
Sequential Cartridge Kit (Incl. Cartridge, spacer bush, spindle adaptor, retaining nut)
LEVSQSBA
LEVA Handle 80mm
LEVSQ80378
Wall Trim
LEVSQBFLAN
Colour Indicator Pack (1x Yellow, 1x Grey, 1x Blue, 1x Red)
LEVSQIND
Basin Mixer Body Assembly
LEVSQBMIX
Grub Screw Pin
673480
TROUBLESHOOTING
Problem
Cause
Rectification
Tap is dripping water
Debris is caught inside cartridge
Cartridge is worn or damaged
Pressure too high
Remove and flush Cartridge,
inspect and remove any debris.
Replace Cartridge if damaged.
Install pressure reduction valve,
ensure it is under 500 kPa
Water is leaking from spindle
Seal in Cartridge is worn or
damaged
Pressure too high
Replace Cartridge
Install pressure reduction valve,
ensure it is under 500 kPa
Water is not flowing from tap
Water turned off
Turn water on
Handle is wobbly
Handle feels loose
Spacer bush is missing
Spindle adaptor not adjusted
correctly
Install Spacer Bush
Adjust spindle adaptor –refer
to handle fitting instructions

11
WARRANTY
Product Warranties for Australia
Effective 1 September 2014
Enware Australia Pty Limited (ACN 003 988 314) (“we” or “us”) warrants that this product (also referred to as
“our goods”) will be free from all defects in materials and workmanship for 12 months* from the date of
purchase. Our liability under this warranty is limited at our option to the repair or replacement of the
defective product or part, the cost of repair of the defective product or part or the supply of an equivalent
product or part, in each case if we are satisfied the loss or damage was due to a defect in the materials or
workmanship of the product or part. All products must be installed in accordance with the manufacturer’s
instructions, the PCA, and AS/NZS3500 including any other applicable regulatory requirements.
Making a claim
To make a claim under this warranty you must notify us in writing within 7 days of any alleged defect in the
product coming to your attention and provide us with proof of your purchase of the product together with a
completed Product ServiceRequest form (ENF091), which is available on request from our office or website
(see contact details below). All notifications and accompanying forms must be sent to us marked for the
attention of the Enware Australia Pty Limited, 9 Endeavour Road, Caringbah NSW 2229. We can also be
contacted by telephone [phone]) or by email ([e-mail]). Your costs in making a claim
under this warranty, including all freight, collection and delivery costs, are to be borne and paid by you. We
also reserve the right at our cost to inspect any alleged defect in the product wherever it is located or
installed or on our premises.
Exceptions
This warranty does not apply in respect of any damage or loss due to or arising from:
a) Failure by you or any other person to follow any instructions for use (including instructions and directions
relating to the handling, storage, installation, fitting, connection, adjustment or repair of the product)
published or provided by us;
b) Failure by you or any other person responsible for the fitting, installation or other work on the product to
follow or conform to applicable laws, standards and codes (including the AS/NZ 3500 set of Standards, all
applicable State and Territory Plumbing Codes, the Plumbing Code of Australia and directions and
requirements of local and other statutory authorities); or
c) Any act or circumstance beyond our control including faulty installation or connection, accident, abnormal
use, acts of God, damage to buildings, other structures and infrastructure and loss or damage during transit
or transportation of the product.
Other conditions
Except as provided or referred to in this document, we accept no other or further liability for any damages or
loss (including indirect, consequential or economic loss) and whether arising in contract, tort or otherwise.
Any benefits available to you under this warranty are in addition to any non-excludable rights or remedies
you may have under applicable legislation, including as a “consumer” under the Australian Consumer Law.
To that extent you need to be aware that: Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.
* 1 Year parts and labour on the complete assembly. After 1 year, a further 4 years parts only warranty is
applicable to sequential valve cartridge.

12