Franke PROTRONIC-T PRTR0003 User manual

Installation and operating instructions Montażi instrukcja obsługi
Notice de montage et de mise en service Monterings- og driftsvejledning
Instrucciones de montaje y uso Návod pro montáž a provoz
Istruzioni per il montaggio e l’uso Asennus- ja käyttöohje
Montage- en bedrijfsinstructies Инструкция по монтажу ивводу в
эксплуатацию
ZMI_001_2000105115-PRTR0003_#SALL_#AQU_#V1.fm/08.02.13
Franke Aquarotter GmbH, Germany
EA-Nr.: 7612982184550
FAR-Best.-Nr.: 2000105115
PRTR0003
DE
EN
FR
ES
IT
NL
PL
SV
CS
FI
RU
[email protected] - www.hygiene-shop.eu

2
Inhaltsverzeichnis35.fm
...................................................................................... 3
Please refer to the graphics in the German Installation and
Operating Instructions.
...................................................................................... 11
Les graphiques sont disponibles dans la notice de montage et de
mise en service allemande.
...................................................................................... 20
Por favor, consulte los gráficos en las instrucciones alemanas de
montaje y uso.
...................................................................................... 29
Per le grafiche fare riferimento alle Istruzioni per il montaggio e
l’uso in tedesco.
...................................................................................... 38
De tekeningen kunt u in de Duitse montage- en bedrijfsinstructies
vinden.
...................................................................................... 47
Prosimy przyjąć grafikęz niemieckiej instrukcji montażu i obsługi.
...................................................................................... 56
Bilderna finns i den tyska monterings- och bruksanvisningen.
...................................................................................... 65
Obrázky najdete v nìmeckém návodu k montáži a obsluze.
...................................................................................... 74
Kuvat löydätte saksankielisestä asennus- ja käyttöohjeesta.
...................................................................................... 83
Рисунки приведены винструкции по монтажу иэксплуатации на
немецком языке.
EN
FR
ES
IT
NL
PL
SV
CS
FI
RU
[email protected] - www.hygiene-shop.eu

3
ZMI_001_2000105115-PRTR0003_#SEN_#AQU_#V1.fm
0English
PROTRONIC-T Washbasin Sink Mixer
with mixing lever, 6 Volt Battery
Please refer to the graphics in the German Installation and Operating Instructions.
0Table of Contents
1. Abbreviations and Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Description of Product
5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6. Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7. Scope of Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
8. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
9. Installation Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation, Function and Commissioning
10. Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
11. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
12. Controlling the Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
13. Programmable Function Parameters . . . . . . . . . . . . . . . . . . . . . . 7
Maintenance
14. Maintenance and Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
15. Replacing an Aerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
16. Replacing the Grit Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
17. Replacing the Non-return Valve . . . . . . . . . . . . . . . . . . . . . . . . . . 8
18. Replacing the Solenoid Valve Cartridge . . . . . . . . . . . . . . . . . . . . 9
19. Changing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
20. Fault Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
21. Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
EN
[email protected] - www.hygiene-shop.eu

4
ZMI_001_2000105115-PRTR0003_#SEN_#AQU_#V1.fm
1. Abbreviations and Units
2. Key
Warning!
Failure to observe can result in injury or even death.
Caution!
Failure to observe can result in material damage.
☞Important!
Failure to observe can cause the product to malfunction.
☞Useful information for optimally handling the product.
3. Warranty
Liability is accepted according to the General Terms and Conditions of Business and
Supply.
Use original replacement parts only!
4. Important Notes
• Installation, commissioning and maintenance are to be performed only by a
qualified technician according to the instructions provided and in accordance with
legal requirements and acknowledged rules of technology.
• All technical connection regulations specified by the local water and electricity
supply utility companies must be complied with.
• All rights reserved to make technical alterations.
DN Nominal diameter in mm
SW Width A/F
EA-Nr. European Article Number
FAR-Best.-Nr. Franke-Aquarotter Order No.
Conversion 1 mm = 0.03937 inches
1 inch = 25.4 mm
All length specifications in the graphics are in mm.
[email protected] - www.hygiene-shop.eu

5
ZMI_001_2000105115-PRTR0003_#SEN_#AQU_#V1.fm
5. Application
PROTRONIC-T mains-independent, opto-electronically-controlled washbasin mixer
DN 15 with theft-proof aerator with integrated flow rate regulator, with 6 Volt battery.
For connection to hot and cold water, with temperature-selector lever
6. Technical Specifications
7. Scope of Delivery
8. Dimensions
9. Installation Example
Minimum flow pressure: 1.0 bar
Recommended flow pressure: 1–5 bar
Maximum operating pressure: 10 bar
Calculation flow rate: 0,07 l/s 0,07 l/s
Volumetric flow: 0.10 l/s for 3 bar flow pressure
Voltage supply: 6 V lithium battery (CRP2)
Type of protection: IP 67
Quantity Description
1 PROTRONIC-T pillar tap
with non-return valves and filters
1 Cleaning clip
1 6 V lithium battery
1 Fixing set
1 Installation and Operating Instructions
[email protected] - www.hygiene-shop.eu

6
ZMI_001_2000105115-PRTR0003_#SEN_#AQU_#V1.fm
10. Assembly Instructions
Warning!
Use the fitting only with non-return valves and the grit filters specified.
Failure to observe can result in an increased bacterial load in drinking water and
cause a health risk or even risk of death.
☞Important!
Before installing, flush the pipes in compliance with DIN 1988.
☞Do not shorten the connector hoses located at the fitting.
☞Only use a 6 V lithium battery type CRP2 as a power supply.
10.1 Install the fitting (a) on the washbasin (b).
☞Important!
Observe the range settings when installing on a stainless steel washbasin
Chapter 13.
☞The corner valves (c) must be provided by the customer.
10.2 Screw the connecting hose (d) on to the corner valve.
11. Function
11.1 Allow your hand to approach the sensor.
• Water flows.
11.2 Remove your hand from the sensor.
• Water flow stops automatically after a set flow duration.
☞The range of the sensor and the flow duration can be adjusted with the optional
remote control (FAR Order No. 2000101087).
☞Important!
Reflecting surfaces can influence the sensor. There is a risk of having permanent
reflections (see Chapter 13. for adjusting the sensor range).
“Auto-flush” function
Caution!
When the “Auto flush” function is used, the flow of water must be ensured.
• The "Auto-flush" function ensures that forced flushing takes place to exchange the
water in the tap lines after 24 or 72 hours of non-use.
• The “Auto-flush” function can only be switched on with the optional remote control
(FAR Order No. 2000101087).
• This function is switched off at the factory.
[email protected] - www.hygiene-shop.eu

7
ZMI_001_2000105115-PRTR0003_#SEN_#AQU_#V1.fm
12. Controlling the Temperature
12.1 Set the mixing lever (a) in the desired position.
13. Programmable Function Parameters
The optional remote control FAR Order No. 2000101087 offers the following
functions:
– Range can be set (3-20 cm)
– Turn-off delay can be set (0-10 s)
– Continuous flow can be switched to 3.5 min or 11 min.
– Switching off the fitting
– Basic settings can be restored
– Test mode for simulation without water
– Setting automatic safety switch-off (2–210 s)
– Automatic flushing can be activated
☞Important!
Reflecting surfaces can influence the sensor. There is a risk of having permanent
reflections. The range must be reduced for installations on reflecting surfaces such
as stainless steel washbasins. If this is not sufficient, an additional base/spacing ring
is available (see Chapter 21.).
14. Maintenance and Servicing
Depending on the quality of the water, the local conditions and the rules and
regulations applicable on site, the fitting must be maintained and serviced at regular
intervals.
Perform maintenance on the following components:
• Aerators (see Chapter 15.)
• Filters (see Chapter 16.)
• Non-return valves (see Chapter 17.)
14.1 Push up the cleaning clip (a) in front of the sensor.
☞The fitting is in sleep mode.
14.2 Properly use suitable cleaning agents that are not harmful to the fittings and rinse
with water after use. High-pressure cleaners must not be used for cleaning.
[email protected] - www.hygiene-shop.eu

8
ZMI_001_2000105115-PRTR0003_#SEN_#AQU_#V1.fm
15. Replacing an Aerator
15.1 Use an open-end spanner to unscrew and replace the aerator (a).
16. Replacing the Grit Filters
Filter for corner valve
16.1 Close the corner valves (c).
16.2 Trigger the valve.
16.3 Unscrew the connector hoses (a) from the corner valves.
16.4 Replace the grit filters (b).
16.5 Reassemble in the reverse order.
Filter, solenoid valve cartridge
16.6 Remove the solenoid valve cartridge (see Chapter 18.).
16.7 Use a flat nose pliers to pull the filter (d) out.
16.8 Replace the filter.
☞Important!
Ensure correct installation position. The rib of the filter must not lie on the flow-
through hole.
16.9 Reassemble in the reverse order.
17. Replacing the Non-return Valve
Warning!
All non-return valves must always be replaced as a group.
Failure to observe can result in an increased bacterial load in drinking water and
cause a health risk or even risk of death.
17.1 Close the corner valves (b).
17.2 Trigger the valve.
17.3 Unscrew the connector hoses (a) from the corner valves.
17.4 Take out the grit filters(c).
17.5 Take out the non-return valve (d).
☞Important!
Be careful to insert the non-return valves and grit filters the right way round.
17.6 Reassemble in the reverse order.
[email protected] - www.hygiene-shop.eu

9
ZMI_001_2000105115-PRTR0003_#SEN_#AQU_#V1.fm
18. Replacing the Solenoid Valve Cartridge
18.1 Close the corner valves.
18.2 Trigger the valve.
18.3 Loosen the screw (a) with an Allan key.
18.4 Pull the housing (b) from the base (d).
18.5 Pull off the hose sleeve (c).
18.6 Remove the screws (f).
18.7 Remove the battery housing (e).
18.8 Take out and replace the solenoid valve cartridge (g).
18.9 Reassemble in the reverse order.
19. Changing the Battery
19.1 Pull off the housing and the hose sleeve (see Chapter 18.).
19.2 Remove the battery (a) by swivelling it out.
Caution!
Use only 6 V lithium battery type CRP2.
☞Important!
Ensure correct battery polarity when assembling.
19.3 Reassemble in the reverse order.
[email protected] - www.hygiene-shop.eu

10
ZMI_001_2000105115-PRTR0003_#SEN_#AQU_#V1.fm
20. Fault Correction
If you are unable to correct a fault or if the fault is not described in the fault correction
section, please inform our customer service department!
21. Replacement Parts
Fault Cause Remedy
Water does not flow – Battery dead (red LED lights up) ➯Replace it
– Water-flow volume regulator closed ➯Open it
– Grit filters are clogged with dirt ➯Clean them
– Cleaning clip in front of the fitting ➯Remove
– Electronic system in sleep mode ➯Shine bright light
in front of the
sensor
– Solenoid valve faulty ➯Replace it
Water flows
continuously
– Solenoid valve faulty ➯Replace it
Water flow too weak – Corner valves not fully opened ➯Open it
– Grit filters are clogged with dirt ➯Clean them
– Aerator calcified ➯Clean them
– Supply pressure too low ➯Check it
Water is too hot – Cold water is turned off ➯Open it
– Filter in cold-water part is dirty ➯Replace it
– Non-return valve faulty ➯Replace it
Water is too cold – Hot water is turned off ➯Open it
– Filter in hot-water part is dirty ➯Replace it
– Non-return valve faulty ➯Replace it
Designation Order No.
1 Aerator with flow-
regulator (VPE 10 St.) . . . . . . . . . 2000104691
2 Lithium battery 6 V type CRP2 . . . 2000104846
3 Solenoid valve cartridge
with grit filter . . . . . . . . . . . . . . . . 2000106163
4 Cleaning clip . . . . . . . . . . . . . . . . 2000105795
5 Maintenance kit comprising:
Non-return valve
Grit filters. . . . . . . . . . . . . . . . . 2000105106
6 Hose . . . . . . . . . . . . . . . . . . . . . . 2000109491
Designation Order No.
7 Maintenance kit comprising:
O-rings
Screws
Grit filters . . . . . . . . . . . . . . . . . 2000104898
8 Mixing lever with screw . . . . . . . . . 2000105821
Accessories Order No.
9 Remote control . . . . . . . . . . . . . . . 2000101087
10 Base for installation on
stainless steel washbasin . . . . 2000105834
[email protected] - www.hygiene-shop.eu