EPIC STRENGTH SHOULDER GZFI8073.2 User manual

CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Model No. GZFI8073.2
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal
(inside tower)
QUESTIONS?
At FreeMotion Fitness, we are
committed to providing com-
plete customer satisfaction. If
you have questions, see HOW
TO CONTACT CUSTOMER
CARE on the back cover of this
manual.
Visit our website at
www.freemotionfitness.com
OWNER’S MANUAL

2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
HOW TO CONTACT CUSTOMER CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
TABLE OF CONTENTS

3
1. Read all instructions in this manual before
using the strength machine. Use the strength
machine only as described in this manual.
2. It is the purchaser’s responsibility to ensure
that there is enough space around the
strength machine for the intended exercise.
Do not crowd the strength machine.
3. Using the anchor strap to provide maximum
stability, anchor the strength machine to the
floor where required or whenever possible.
4. Use the strength machine only on a level sur-
face. Cover the floor beneath the strength
machine to protect the floor.
5. It is the responsibility of the owner to ensure
that all users of the strength machine are
adequately informed of all precautions, have
read and understood all warning and caution
labels, and are informed of how to use the
strength machine properly.
6. Keep children under 12 and pets away from
the strength machine at all times.
7. Always wear athletic shoes for foot protec-
tion while exercising.
8. Keep hands and feet away from moving
parts. Do not lean on or rest your hands on
the strength machine when it is in use.
9. All users of the strength machine should be
instructed to report any injury or strength
machine irregularity to facility staff immedi-
ately.
10. Make sure the weight pin is completely
inserted into one of the weight plates.
11. Check all cables, cable connections, and pul-
leys before each use of the strength machine.
Make sure all parts are properly tightened.
Replace any worn parts immediately.
12. Make sure the cable remains on the pulleys
at all times. If the cable binds while you are
exercising, stop immediately and make sure
the cable is on the pulleys and nothing is
interfering with the cable or pulleys. Replace
all cables at least every two years.
13. The strength machine is designed to support
amaximum user weight of 350 lbs. (159 kg).
14. Keep the strength machine indoors, away
from moisture and dust. Do not put the
strength machine in a garage or covered
patio, or near water.
15. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
WARNING: To reduce the risk of serious injury, read the following important precautions
before using the strength machine.
IMPORTANT PRECAUTIONS

WARNING DECAL PLACEMENT
4
The decals shown below have been placed
on the strength machine in the indicated
locations. If a decal is missing or illegible,
see HOW TO CONTACT CUSTOMER CARE on
the back cover of this manual to order a free
replacement decal. Apply the decal in the
location shown.
Decal 1
Shown at 70%
GZ7003
Decal 4
Shown at 85%
Decal 2
GZ7026
Decal 2
Decal 4
Decal 1
Decal 3
Decal 3

Assembled Dimensions:
Height: 62 in. (1.57 m)
Width: 70 in. (1.78 m)
Depth: 70 in. (1.78 m)
5
Base
Cam
Anchor Strap
Arm
Counter-
weight
Weights
Weight Pin
Backrest
Seat
Tower
BEFORE YOU BEGIN
Thank you for selecting the EPIC STRENGTH™
SHOULDER strength machine. The strength
machine’s stylish ergonomic design and never-before-
seen features improve upon traditional strength train-
ing. The innovative features and quality construction
provide a reliable product for your club. And the
advanced solutions to isolating individual muscle
groups make the SHOULDER strength machine a key
tool for members to reach their goals.
For your benefit, read this manual carefully before
using the strength machine. If you have questions
after reading this manual, see HOW TO CONTACT
CUSTOMER CARE on the back cover of this manual. To
help us assist you, please note the product model
number and serial number before calling. The model
number is GZFI8073.2. The serial number can be
found on a decal attached to the strength machine
(see the front cover of this manual).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.

This section explains how to adjust the strength machine. Make sure all parts are properly tightened each time
the strength machine is used. Replace any worn parts immediately.
6
ADJUSTING THE RESISTANCE
Tochange the amount of resistance for your workout,
insert the weight pin into the desired weight. Make
sure that the weight pin is fully inserted into the
weight.
ADJUSTMENTS
Weight
Weight
Pin
ADJUSTING THE SEAT
To raise the seat, lift on the end of the seat and move
the seat to the desired position. Tolower the seat, lift
on the end of the seat and press down on the back of
the seat until the seat is at the desired height.
Lift
Press
Seat

7
MAINTENANCE
For safe and trouble-free operation of your EPIC STRENGTH strength equipment, it is important to perform
preventive maintenance on a regular basis. Make sure that all parts are properly tightened each time the strength
machine is used. Replace any worn parts immediately. The strength machine can be cleaned with a cloth damp-
ened with water and a mild, non-abrasive soap. Do not use solvents.
Note: Instruct all personnel to perform equipment inspection and maintenance requirements. Personnel must
record and report any accident. For any questions or concerns, see HOW TO CONTACT CUSTOMER CARE
on the back cover of this manual.
Use only original EPIC STRENGTH parts for repair or replacement to maintain your machine’s warranty.
FreeMotion Fitness recommends the following procedures:
SCHEDULED MAINTENANCE
DAILY
1. Upholstery—General cleaning:
•Wipe using a cloth dampened with a solution of
warm water and a mild soap.
•If necessary,use a soft bristle brush with the
cleaning solution.
•Always remove the cleaning solution using a
cloth dampened with clean water. Rinse often.
2. Upholstery—Difficult stains:
•Spray the stain with a non-abrasive household
cleaner such as FORMULA 409®cleaner,
SIMPLE GREEN®,or a similar product.
•Rub the area gently and let it sit for a few min-
utes.
•Rinse thoroughly using a cloth dampened with
clean water.
•Repeat if necessary using a soft bristle brush.
Optional method for difficult stains:
•Rub the area gently using a cloth dampened
with rubbing alcohol.
•Rinse thoroughly using a cloth dampened with
clean water to remove alcohol residue.
CAUTION: When using any cleaning product, try
it first in an inconspicuous place to ensure there
is no damage to the material. Follow directions
and adhere to safety precautions of each manu-
facturer of cleaning agent used. FreeMotion
Fitness and its vendors cannot be held liable for
damage or injuries resulting from the use or mis-
use of cleaning products.
3. Towers and Frames:
•Wipe using a cloth dampened with a solution of
warm water and a mild soap.
•Rinse and dry thoroughly.
Important: Do not use abrasive cleaners because
they may scratch the equipment. Strong cleansers
and abrasives will damage decals. Use caution
around decals. Do not use solvents such as lacquer
thinner, kerosene, gasoline, or similar liquids.
WEEKLY
1. Hardware:
•Check all nuts and bolts. Tighten them as
required.
2. Cables:
•Check all cables for proper tension.
•Check the entire length of the cable by pulling
each handle individually to its fully extended
position and inspecting the cable that is
exposed on the exterior of the machine, as well
as the cable inside of the cut stack tower.
•Run your fingers along the cable, paying close
attention at the bends and attachment points.
•Watch for the following conditions, which may
indicate a worn cable in need of replacement:
A. torn or split cable sheath that exposes the
cable
B. kinked or severely bent cable
C.curled or twisted sheath
D.stretched cable sheath, showing a thinning
cross-section
A
B
D
C

8
MONTHLY
1. Grips:
•Check and replace as needed.
YEARLY OR AS REQUIRED
1. Weight Stack Guide Rods:
•Clean and lubricate the full length by wiping
using a soft cloth containing a lightweight
motor oil, 10W-40 or 10W-30 weight. Only a
light coating over the entire length is needed.
Note: Do not use TEFLON®or silicone-
based lubricants.
CUSHION ATTACHMENT
Important: All EPIC STRENGTH cushions are fabri-
cated using dense plywood with tee-nuts installed for
bolting to the machine framework. Because these tee-
nuts are held by the plywood, they will not withstand
the torque that standard nuts and bolts will.
Therefore, when tightening the cushion bolts, turn
them only until they are snug and the cushion does
not move or feel loose. Overtightening may strip the
tee-nuts from the plywood and make it impossible to
remove the cushion in the future.
CABLE TENSION CHECK
1. Insert the weight pin into the top weight plate.
2. Slowly raise and lower the top weight by normal
machine use. The top weight should come to
rest just on top of the second weight when the
handle is returned to the resting position.
•If there is too much tension on the cable, the
top weight will not rest on the second weight,
and it may be difficult to insert the weight pin
into the weight plates.
•If there is not enough tension on the cable, the
top weight will not be lifted immediately when
one of the handles is pulled. Ideally, the han-
dle/cable should not move more than 1/2"
(1.3cm) from the resting position before the top
weight begins to be lifted.
3. If there is too much or not enough tension on the
cable, adjust the cable as described in CABLE
ADJUSTMENTS.

9
CABLE ADJUSTMENTS
CAUTION: After making any cable adjustment, pull
the handle using a light load and have someone make
sure that the cable is not derailed from a pulley or rub-
bing on a guard (see CABLE GUARDS on page 10).
INITIAL ADJUSTMENT
Top Weight Adjustment—
Tools required: Hammer, 1/8” punch, 3/16” roll pin
1. Lift the coupler cover from the top weight coupler.
2. Remove the roll pin from the top weight coupler
with an 1/8” punch and a hammer.
3. Align the hole in the cable coupling with the
appropriate adjustment hole in the top weight
coupler:
•If more slack is needed in the cable, align the
cable coupling with a higher hole.
• If less slack is needed in the cable, align the
cable coupling with a lower hole.
4. With the cable coupling aligned with the new
hole, drive a new roll pin into the top weight cou-
pler and cable coupler.
5. Lower the coupler cover over the top weight
coupler.
Adjustment Hole
Cable Coupling
Top Weight
Coupler
Coupler Cover
ADDITIONAL ADJUSTMENTS
Floating Pulley Adjustment–
Tools required: Adjustable wrench/spanner
1. Lift the top weight off the
weight stack and insert the
weight pin into the second
weight and the sixth hole
from the top of the weight
rod.
2. Rotate the cam clockwise
and disengage the cam
cable on the small cam.
3. Loosen the nut below the
“U”-bracket.
To remove slack from the
cables, turn the cam cable
clockwise into the “U”-
bracket.
Toadd slack to the cables, turn the cam cable
counterclockwise out of the “U”-bracket.
4. Retighten the nut against the “U”-bracket and re-
engage the cam cable onto the small cam.
5. Lift the top weight and remove the weight pin.
Lower the top weight onto the second weight.
6. Readjust as necessary.

10
Tower Pulley Adjustment–
Tools required: 5/16" Allen wrench/hex key, 9/16"
open end wrench/spanner
1.Lift the top weight off the
weight stack and insert the
weight pin into the second
weight and the sixth hole
from the top of the weight
rod.
CABLE GUARDS
Check for alignment periodically to ensure that cable
guards are not rubbing on the cable and that they are
performing their intended duty. If the alignment is not
proper, loosen the bolt slightly, readjust the cable
guard as necessary, and retighten the bolt.
Correct Alignment
Incorrect Alignment
Rubbing Rubbing
Out of
Alignment
Guards Guards
Cable
Cable
Pulley
2. Loosen the locknut attach-
ing the pulley to the brack-
et in the top of the tower.
3. Move the pulley to the appropriate location in the
bracket:
• If more slack is needed in the cable, move the
pulley down.
• If less slack is needed in the cable, move the
pulley up.
4. Make sure that the pulley guard is properly ori-
ented (see CABLE GUARDS) and retighten the
locknut attaching the pulley to the bracket.
5. Lift the top weight and remove the weight pin.
Lower the top weight onto the second weight.
6. Readjust as necessary.
Locknut

11
SERVICING THE WEIGHT STACK
For required parts, see HOW TO CONTACT CUS-
TOMER CARE on the back cover of this manual.
1. Remove the wingnuts under the tower cap and
remove the tower cap from the tower.
2. Remove the screw from the top of each guide
rod.
3. Lift the coupler cover and drive the roll pin from
the top weight coupler with an 1/8” punch and a
hammer—this will release the cable.
4. Lift the guide rods out of the top of the tower.
5. Lift and rotate the top weight and weight pin, and
remove them through the front opening of the
tower.
6. Servicing the weight stack involves replacing the
two guide bushings and the weight insert in the
top weight. First, use a punch to drive the two
existing guide bushings and the weight insert out
of the top weight.
7. To insert the new guide bushings and weight
insert, hold a bushing square to the face of one
of the holes in the top weight, place a protective
piece of wood on top of the bushing, and lightly
tap the bushing into place. The bushing should
be flush with the surface. Repeat with the other
guide bushing and weight insert.
8. Replace the top weight and weight pin on top of
the weight stack.
9. Reattach the cable to the top weight coupler.
10. Clean and lubricate the guide rods by wiping
them with a soft cloth containing a light weight
motor oil, 10W-40 or 10W-30 weight. Apply only a
light coating over the entire length. Note: Do not
use TEFLON®or silicone-based lubricants.
11. Reinsert the guide rods through the top of the
tower and into the weight stack.
Note: If the weight stack has shifted, use a
short bar to realign the holes in the weight
plates. Hold the weight plates while inserting
the guide rods.
12. Reattach the guide rods to the top of the frame
with the two screws.
13. Insert the weight pin in the top weight. Pull the
handle, lifting the top weight all of the way to the
top. Slowly return the handle to the resting posi-
tion. If the top weight sticks, loosen one of the
guide rod screws. Lift the top weight to the top
again. Retighten the guide rod screw. Check the
full travel again and readjust the guide rods as
necessary.
14. While slowly pulling the handle, have someone
check the top weight pulley guard to ensure that
it is not dragging or rubbing on the cable.
15. Replace the tower cap and retighten the
wingnuts onto the button bolts.
Weight
Insert
Guide
Bushings
Top Weight
Top Weight
Coupler
WARNING: Do not force the
guide rods into the weights; doing so will
damage the bushings and weight inserts.

12
CABLE DIAGRAM
The cable diagram below shows the proper route of the cables. Use the diagram to make sure that the cables
and the cable guards have been assembled correctly. If the cables have not been correctly routed, the strength
machine will not function properly and damage may occur. The numbers show the correct route of the cables.
Make sure that the cable guards do not touch or bind the cables.
1
2
Tower Cable (34)
Arm Cable (55)
Cam Cable (56)
3
45
1
2
3
1
2

13
NOTES

14
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice.
Key No. Qty. Description Key No. Qty. Description
1 1 Frame
2 1 Tower
3 1 Tower Cap
4 1 Right Arm
5 1 Left Arm
6 1 Backrest
7 1 Seat
8 1 Seat Frame
9 2 Weight Guide
10 2 Long Trim
11 19 Weight
12 1 Weight Rod
13 1 Top Weight
14 1 Long Panel Frame
15 1 Long Panel
16 1 Short Panel Frame
17 1 Short Panel
18 1 Anchor Strap
19 3 Pulley
20 4 Tower Foot
21 12 3/8" x 1/2" Button Screw
22 1 “U”-bracket
23 1 “V”-pulley
24 4 Rivet
25 1 Rod Washer
26 2 Small Weight Bumper
27 39 Weight Insert
28 1 3/16" Roll Pin
29 2 Guide Bushing
30 1 3/8" x 1 3/4" Bolt
31 1Star Washer
32 1 Rod Nut
33 1 Coupler Cover
34 1 Tower Cable
35 2 Counterweight
36 2 Large Bumper
37 1 3/8" x 2 1/2" Bolt
38 2 “V”-pulley Bearing
39 2 Bushing
40 7 Serrated Washer
41 1 Cover
42 1 Rear Name Plate
43 1 Rear Plate Frame
44 1 Weight Pin
45 2 Frame Foot
46 1 Cam
47 2 Wingnut
48 1 Bungee Cord
49 1 Short Trim
50 6 Snap Ring
51 6 1" Bearing
52 2 Short Pivot Rod
53 2 Cable Guard
54 4 3/8" x 1 1/4" Bolt
55 1 Arm Cable
56 1 Cam Cable
57 6 Pivot Washer
58 2 1/4" x 3/8" Bolt
59 1 Long Pivot Rod
60 2 1/4" x 1" Button Bolt
61 2 3/8" x 3/4" Self-tapping Screw
62 2 1/2" x 1 1/4" Bolt
63 1 3/8" x 6 1/2" Non-patch Bolt
64 5 3/8" x 1" Non-patch Bolt
65 2 3/8" x 2" Bolt
66 4 3/8" x 2 3/4" Bolt
67 2 Handle Grip
68 2 Handle Bushing
69 2 #4 x 5/8" Screw
70 2 Handle Endcap
71 21/4" x 1" Flat Head Screw
72 6 3/8" Nylon Locknut
73 1 Backrest Bracket
74 2 Wire Tie
75 1 Insignia
76 2 #4 Nut
77 1 3/8" Fine-thread Nut
78 2 Bushing
# 1 User’s Manual
PART LIST—Model No. GZFI8073.2 R0405A
If replacement parts are needed, or if parts are missing or damaged, see HOW TO CONTACT CUSTOMER
CARE on the back cover of this manual.

EXPLODED DRAWING—Model No. GZFI8073.2 R0405A
48
74
20
20
20
20
21 21
21 21
72 53
19
65
2
15
16
17
14
41
75
19
43
42
65
47
47
3
60
9
6161
61
6767
68
70
71
10
10
33
32
31
29 13
25
34
29
28
12
67
27
27
44
11
26 26
6
18
62
7
64 64
8
49
45 1
63
64
73
54
50 51
55
51 52 5
50
57
52
51
55
54
4
50
5751
66
66
35
66
66
35
57
50
51
57
37
39
38
23
38
39
72
54
36
72
72
36
46
51
57
50 56
59
51
57
50
34
45
27
72
19
56
40
30 22
40
21
21
21
21
70
71
68
58
69
76
76
40
77
24
24
24
24
58
72
53
54
40
40
78
78
40
40
15

Part No. GZ7262 R0405A Printed in USA © 2005 ICON IP, Inc.
HOW TO CONTACT CUSTOMER CARE
If you have questions after reading this manual, or if you require assistance, please contact Customer Care at
the address and phone number listed below. Please be prepared to give the following information:
•The MODEL NUMBER of the product (GZFI8073.2).
• The NAME of the product (EPIC STRENGTH SHOULDER strength machine).
• The SERIAL NUMBER of the product (see the front cover of this manual).
• When ordering replacement parts, please also give the KEY NUMBER and DESCRIPTION of the part(s) (see
the PART LIST and the EXPLODED DRAWING on pages 14 and 15 of this manual).
Customer Care: 1-800-201-2109, Monday–Friday, 8 a.m.–5 p.m. Mountain Time
FreeMotion Fitness, Inc. • 1096 Elkton, Suite 600 • Colorado Springs, CO 80907